分形特征表面接触磨损模拟

宿月文 1; 陈渭 2; 朱爱斌 2; 范天峰 1; 郭彩霞 1

doi:10.7652/xjtuxb201307010

您当前的位置：

首页 >

文章列表页 >

分形特征表面接触磨损模拟

更新时间：2025-07-09

- 分形特征表面接触磨损模拟
- Contact and Wear Simulation Between Fractal Surfaces
- 西安交通大学学报 2013年47卷第7期页码：52-56
- 作者机构：
  
  西北机电工程研究所,陕西,咸阳,712000
- 作者简介：
- 基金信息：
  
  : 2012-12-16。作者简介: 宿月文(1979—),男,工程师。基金项目: 国家自然科学基金资助项目(51175409-E050504)
- DOI：10.7652/xjtuxb201307010
  中图分类号： TH117.1
- 网络首发：2013-07-10，
  
  纸质出版：2013
- 稿件说明：
移动端阅览
宿月文 1, 陈渭 2, 朱爱斌 2, 等. 分形特征表面接触磨损模拟[J]. 西安交通大学学报, 2013,47(7):52-56.

Contact and Wear Simulation Between Fractal Surfaces[J]. 2013, 47(7): 52-56.
宿月文 1, 陈渭 2, 朱爱斌 2, 等. 分形特征表面接触磨损模拟[J]. 西安交通大学学报, 2013,47(7):52-56. DOI： 10.7652/xjtuxb201307010.

Contact and Wear Simulation Between Fractal Surfaces[J]. 2013, 47(7): 52-56. DOI： 10.7652/xjtuxb201307010.

摘要

为实现粗糙表面微观接触磨损的精确预测

根据分形理论对传统的只考虑弹性-塑性两状态的二维分形接触模型进行了修正

并构建了包含弹性-弹塑性-塑性完全状态的三维粗糙表面分形接触模型。通过去除塑性接触微凸体在截断平面作用下形成的球台方法来模拟微观磨损

磨损系数由被去除的球台体积与总接触微凸体体积之比来表征

采用数值仿真分析了磨损系数与分形参数、载荷和材料等因素间的依赖关系。计算结果表明

磨损系数随表面粗糙程度的增大而增大

随接触载荷的增大而减小并趋于相对稳定。接触副材料属性决定了微凸体临界接触面积

进而影响了磨损系数。该模型给出了微观磨损机理的数学描述

为界面接触磨损研究提供了新思路。

Abstract

The traditional 2D fractal contact theory only takes elastic and plastic contact of asperities into account. To predict contact and wear microscopically

a novel model was proposed which includes all of the elastic

elastic-plastic and fully plastic deformation regimes for asperity of fractal surface. A generalized adhesive wear analysis was developed for 3D fractal surfaces in normal contact. Worn particles can be modeled by the removal of material from the spherical cap for fully-plastic asperity truncated by a rigid plane. Wear progress was discretized into several incremental steps

and characterized as wear rate to define as the total volume of wear particles divided by the total volume of all contacting asperities. Contact and wear problem were examined numerically to illustrate the dependence of wear rate on fractal parameters

loads and material properties. The numerical results indicate that wear rate increases with the increasing surface roughness. As the normal load is increased

wear rate decreases and tends relatively static. Material properties have influences on the critical truncated contact area and wear rate.

关键词

Keywords

references

MAJUMDAR A, BHUSHAN B. Fractal model of elastic-plastic contact between rough surfaces [J]. ASME Journal of Tribology, 1991, 113(1): 1-11.

YAN W, KOMVOPOULOS K. Contact analysis of elastic-plastic fractal surfaces [J]. Journal of Applied Physics, 1998, 84(7): 3617-3624.

尤晋闽, 陈天宁. 结合面法向动态参数的分形模型 [J]. 西安交通大学学报, 2009, 43(9): 91-94.

YOU Jinmin, CHEN Tianning. Fractal model for normal dynamic parameters of joint surfaces [J]. Journal of Xi'an Jiaotong University, 2009, 43(9): 91-94.

张学良, 温淑花, 兰国生, 等. 平面结合面切向接触阻尼分形模型及其仿真 [J]. 西安交通大学学报, 2011, 45(5): 74-77.

ZHANG Xueliang, WEN Shuhua, LAN Guosheng, et al. Fractal model for tangential contact damping of plane joint interfaces with simulation [J]. Journal of Xi'an Jiaotong University, 2011, 45(5): 74-77.

ZHOU G Y, LEU M C, BLACKMORE D. Fractal geometry model for wear prediction [J]. Wear, 1993, 170(1): 1-14.

葛世荣, 朱华. 摩擦学的分形 [M]. 北京: 机械工业出版社, 2005: 249-260.

GREENWOOD J A, WILLIAMSON J B P. Contact of nominally flat surfaces [J]. Proceedings of the Royal Society of London Series A: Mathematical and Physical Sciences, 1966, 295(1442): 300-319.

KOGUT L, ETSION I. Elastic-plastic contact analysis of a sphere and a rigid flat [J]. ASME Journal of Applied Mechanics, 2002, 69(5): 657-662.

SUH N P. Tribophysics [M]. Englewood Cliffs, NJ, USA: Prentice-Hall, 1986: 66-69.

YANG J, KOMVOPOULOS K. A mechanics approach to static friction of elastic-plastic fractal surfaces [J]. ASME Journal of Tribology, 2005, 127(2): 315-324.

RABINOWICZ E. Friction and wear of materials [M]. New York, USA: John Wiley Sons, 1966: 145-170.

阎维平, 马凯, 高正阳, 董静兰.增压富氧燃煤锅炉省煤器管束磨损研究.2013,47(3): 53-59.

吕正,陈昊,陈峰.一种ARM存储模型的快速检测方法.2013,47(6):68-72.

高庆,陶加银,宋立明,李军.涡轮轮缘密封封严效率的数值研究.2013,47(5):12-17.

霍文浩,晏鑫,李军,丰镇平.超超临界汽轮机高压缸旁路冷却系统冷却特性研究.2013,47(5):24-30.

张东亚, 林平, 董光能, 曾群锋, 毛军红.性能可调的自润滑叠层复合材料的摩擦学行为研究。2012,46(11):53-57.

赵明露, 刘炳, 高填.Al-2.15%Mn合金的组织及摩擦学特性.2012,46(9):119-124.

金台, 罗坤, 杨建胜, 樊建人.采用内嵌边界方法模拟错列管束的磨损.2012,46(7):122-127.

侯书增, 鲍崇高, 付青然, 张志云, 严靖博.硬质合金/高铬铸铁基复合材料的界面特性及磨损性能研究.2012,46(5):73-78.

杨旭,屈宗长,吴裕远,于漠南.同步回转式混输泵端面的相对运动及摩擦分析.2011,45(9):90-93.

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

随机抽样在粗糙表面接触力学行为分析中的应用

重载下滚动直线导轨副的接触特性

碳/ 碳复合材料表面聚四氟乙烯复合涂层的摩擦学性能

尺蠖型压电旋转驱动器钳位特性分析

纳米流道内液体特性的分子动力学研究