实际叶片前缘冲击冷却流动和换热的数值研究

刘钊; 丰镇平; 宋立明

您当前的位置：

首页 >

文章列表页 >

实际叶片前缘冲击冷却流动和换热的数值研究

更新时间：2025-07-09

- 实际叶片前缘冲击冷却流动和换热的数值研究
- Numerical Study on Flow and Heat Transfer of Impingement Cooling on Leading Edge of Actual Turbine Blade
- 西安交通大学学报 2011年45卷第1期页码：5-9+20
- 作者机构：
  
  西安交通大学叶轮机械研究所,西安,710049
- 作者简介：
- 基金信息：
  
  : 2010-05-12. 作者简介: 刘钊(1982-),男,博士生;丰镇平(联系人),男,教授,博士生导师. 基金项目: 国家重点基础研究发展计划资助项目(2007CB210107)
- DOI：
  中图分类号： TK474.7
- 网络首发：2011-01-10，
  
  纸质出版：2011
- 稿件说明：
移动端阅览
刘钊, 丰镇平, 宋立明. 实际叶片前缘冲击冷却流动和换热的数值研究[J]. 西安交通大学学报, 2011,45(1):5-9+20.

Numerical Study on Flow and Heat Transfer of Impingement Cooling on Leading Edge of Actual Turbine Blade[J]. 2011, 45(1): 5-9+20.
刘钊, 丰镇平, 宋立明. 实际叶片前缘冲击冷却流动和换热的数值研究[J]. 西安交通大学学报, 2011,45(1):5-9+20. DOI：

Numerical Study on Flow and Heat Transfer of Impingement Cooling on Leading Edge of Actual Turbine Blade[J]. 2011, 45(1): 5-9+20. DOI：

摘要

应用数值方法研究了射流孔径对燃汽轮机透平叶片前缘内部冲击冷却流动和换热的影响

并采用商用计算流体力学软件CFX11.0求解稳态可压时均N-S方程

且SST κ-ω湍流模型的总体求解精度为二阶.以某典型燃汽轮机透平叶片前缘中截面拉伸的曲面为研究对象

同时考虑了相同射流量下的4种不同射流孔径的影响

经研究表明:在计算条件下

随着射流孔径增大

靶面上平均努塞尔数和弧长方向平均努塞尔数沿展向的分布都更为均匀

从中截面到叶顶位置的分布更是如此; 靶面上的努塞尔数和弧长方向平均努塞尔数的最小值随着射流孔径的增大而增大

这说明采用大射流孔径可以有效提高冲击冷却的换热量

减小冲击冷却引起的热应力.

Abstract

A numerical study was performed to simulate the flow and heat transfer of impingement cooling on the leading edge of a turbine blade. Calculations were done by using a commercial CFD software CFX11.0 to solve Reynolds-averaged N-S equations in conjunction with the SST κ-ω two-equation turbulence model with an overall accuracy of the second order. The influences of four jet nozzle diameters at the same mass flow rate were considered for a target surface stretched by the middle cross section of the internal leading edge of a typical modern gas turbine blade. The result shows that the Nusselt number at the turbine blade leading edge and the streamwise average Nusselt number are more even when the jet nozzle diameter is larger

especially from the middle span to the tip of the blade. The minimum values of Nusselt number of the turbine blade leading edge and streamwise average Nusselt number will increase with the jet nozzle diameter

indicating that larger jet nozzle diameters will improve the performance of impingement cooling on the leading edge of a turbine blade.

关键词

Keywords

references

HAN J C. Gas turbine heat transfer and cooling technology[M]. New York,USA: Taylor & Francis, 2000.

CHUPP R E, HELMS H E, MCFADDEN P W, et al. Evaluation of internal heat transfer coefficients for impingement cooled turbine airfoils[J]. Aircraft, 1969, 6(3): 203-208.

BUNKER R S, METZGER D E. Local heat transfer in internally cooled turbine airfoil leading edge regions: part Ⅰ impingement cooling without film coolant extraction[J]. ASME J Turbomachinery, 1990, 112(3): 451-458.

CHOI M, YOO H S, YANG G, et al. Measurements of impinging jet flow and heat transfer on a semi-circular concave surface[J]. Int J Heat Mass Transfer, 2000, 43(10): 1811-1822.

KUMA B V N R, PRASAD B V S S S. Computational flow and heat transfer of a row of circular jets impinging on a concave surface[J]. Heat Mass Transfer, 2008, 44(6): 667-678.

ALVAREZ J J, CALZADA P D L, KRULIC G. Heat transfer and flow characteristics of a leading edge impingement cooling system for low pressure turbine vanes,ASME Paper GT2008-50142 [R]. Norcross, USA: ASME International Gas Turbine Institute, 2008.

郑际睿, 王宝官. 模拟透平叶片冲击冷却的实验研究[J]. 工程热物理学报, 1980, 1(2):165-175.

ZHEN Jirui, WANG Baoguan. Experimental investigation of simulating impingement cooling of concave surfaces of turbine airfoils[J]. Journal of Engineering Thermophysics, 1980, 1(2):165-175.

苑中显, 阎小军, 王秋旺,等. 实际叶型前缘冲击冷却换热的液晶显示实验研究[J]. 西安交通大学学报, 1999, 33(11):55-59.

YUAN Zhongxian, YAN Xiaojun, WANG Qiuwang, et al. Liquid crystal thermography applied to jet impingement heat transfer for leading edge of blade[J]. Journal of Xi'an Jiaotong University, 1999, 33(11):55-59.

TIMKO L P. Energy efficient engine high pressure turbine component test performance report, NASA CR_168289 [R].Washington, DC, USA:NASA, 1984.

LIU Zhao, FENG Zhenping, SONG Liming. Numerical study of flow and heat transfer of impingement cooling on model of turbine blade leading edge, ASME Paper GT2010-23711 [R]. Norcross, USA: ASME International Gas Turbine Institute, 2010.

杨佃亮, 丰镇平. 叶顶形状对动叶顶部流动和传热的影响研究[J]. 西安交通大学学报, 2008, 42(5):537-541.

YANG Dianliang, FENG Zhenping. Effect of squealer geometry arrangements on tip leakage flow and heat transfer for turbine blade [J]. Journal of Xi'an Jiaotong University, 2008, 42(5):537-541.

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

带肋曲面双层壁偏转内流与传热冷却特性数值研究

曲面双层壁结构的内外复合流动及综合冷却特性数值研究

带肋曲面双层壁偏转内流与传热冷却特性数值研究

燃气透平冲击冷却的射流孔形状优化方法及验证

气膜抽吸作用下透平叶片冲击冷却的一维管网计算方法研究