轴承结合部动态参数识别与等效分析模型的研究

方兵; 张雷; 赵继; 曲兴田

您当前的位置：

首页 >

文章列表页 >

轴承结合部动态参数识别与等效分析模型的研究

更新时间：2025-07-09

- 轴承结合部动态参数识别与等效分析模型的研究
- Dynamic Parameter Identification and Modeling for Bearing Joint Interfaces
- 西安交通大学学报 2012年46卷第11期页码：69-74
- 作者机构：
  
  吉林大学机械科学与工程学院,长春,130022
- 作者简介：
- 基金信息：
  
  : 2012-05-07. 作者简介: 方兵(1985-),男,博士生;张雷(通信作者),男,教授. 基金项目: 国家科技重大专项课题资助项目(2009ZX0401-035)
- DOI：
  中图分类号： TH133
- 网络首发：2012-11-10，
  
  纸质出版：2012
- 稿件说明：
移动端阅览
方兵, 张雷, 赵继, 等. 轴承结合部动态参数识别与等效分析模型的研究[J]. 西安交通大学学报, 2012,46(11):69-74.

Dynamic Parameter Identification and Modeling for Bearing Joint Interfaces[J]. 2012, 46(11): 69-74.
方兵, 张雷, 赵继, 等. 轴承结合部动态参数识别与等效分析模型的研究[J]. 西安交通大学学报, 2012,46(11):69-74. DOI：

Dynamic Parameter Identification and Modeling for Bearing Joint Interfaces[J]. 2012, 46(11): 69-74. DOI：

摘要

针对轴承结合部有限元分析模型参数难以确定的问题

提出了基于模态实验数据的建模方法

分析了球轴承接触变形的特点.利用拉格朗日力学分析原理建立了球轴承装配结构3自由度的动力学方程

依据模态实验测得的固有频率和阻尼比

采用最小二乘法解得单个钢球在接触法线方向上的刚度和阻尼

进而计算得到了轴承结合部在径向、轴向以及转角等3个方向的刚度和阻尼.采用弹簧阻尼单元模拟轴承结合部的结构动力学方程

通过与由拉格朗日力学分析原理建立的动力学模型的对比

来确定弹簧阻尼单元的数值

并建立了轴承结合部有限元分析模型.研究结果表明:在对装配结构有限元进行分析计算时

结构前3阶固有频率及振型与实验测得的振型一致

对应固有频率的相对误差在5%以内.

Abstract

Aiming at the key problem in determining the parameters of finite element analysis(FEA)model of bearing joint interfaces

a new scheme according to the experimental data of modal testing is proposed. A 3-DOF dynamic equation following Lagrange theory is reported for the analysis to ball bearing vibrations

the stiffness and damping along normal of single ball is obtained by least square method

then the stiffness and damping matrix of bearing joint interfaces are identified. A new 3-DOF dynamic equation by two pairs of springs instead of the ball bearings is established

where the of spring values are calculated by substituting the stiffness and damping matrix into new equation to gain the FEA model of structure containing ball bearing. The results show that the first three modes by the FEA model coincide well with the experiments

and the error of natural frequencies gets less than 5%.

关键词

Keywords

references

张学良.机械结合面动态特性及应用 [M].北京:中国科学技术出版社,2002:1-9.

BOGRAD S, REUSS P, SCHMIDT A, et al. Modeling the dynamics of mechanical joints [J]. Mechanical Systems and Signal Processing, 2011,25(8):2801-2826.

赵宏林,丁庆新,曾鸣,等.机床结合部特性的理论解析及应用 [J].机械工程学报,2008,44(12): 208-214.

ZHAO Honglin, DING Qingxin, ZENG Ming, et al. Theoretic analysis on and application of behaviors of machine tool joints [J].Chinese Journal of Mechanical Engineering, 2008,44(12): 208-214.

HARRIS T A, KOTZALSA M N. Advanced concepts of bearing technology [M]. New York, USA: Taylor Francis, 2006:1-40.

LIM T C, SINGH R. Vibration transmission through rolling element bearings: Part I Bearing stiffness formulation [J]. Journal of Sound and Vibration, 1990, 139(2): 179-199.

LIM T C, SINGH R. Vibration transmission through rolling element bearings: Part IV Statistical energy analysis [J]. Journal of Sound and Vibration, 1992, 153(1): 37-50.

谢涛,刘品宽,陈在礼.转台轴系轴承刚度矩阵的理论推导与数值计算 [J]. 哈尔滨工业大学学报,2003,35(3): 329-333.

XIE Tao, LIU Pinkuan, CHEN Zaili. Theoretical analysis and numerical estimation of stiffness matrix of angular contact ball bearing in a spindle-bearing system[J]. Journal of Harbin Institute of Technology, 2003,35(3): 329-333.

刘卫群,罗继伟,吴长春,等.滚动轴承刚度分析程序[J].计算力学学报,2001,18(3): 375-378.

LIU Weiqun, LUO Jiwei, WU Changchun, et al. Program for the stiffness analysis of rolling bearing[J].Chinese Journal of Computational Mechanics, 2001,18(3):375-378.

刘显军,洪军,朱永生,等.多支承轴系轴承受力与刚度的有限元迭代计算方法 [J].西安交通大学学报,2011,44(11): 41-45.

LIU Xianjun, HONG Jun, ZHU Yongsheng, et al. Iterative method to solve bearing's force and stiffness for a multi-support spindle system based on finite element analysis [J].Journal of Xi'an Jiaotong University, 2011,44(11):41-45.

ROYSTON T J, BASDOGAN I. Vibration transmission through self-aligning(spherical)rolling element bearings: theory and experiment [J]. Journal of Sound and Vibration, 1998, 215(5): 997-1014.

ROOK T E, SINGH R. Structural intensity calculations for compliant plate-beam structures connected by bearings [J]. Journal of Sound and Vibration, 1998, 211(3): 365-387.

LYNAGH N, RAHNEJAT H, EBRAHIMI M, et al. Bearing induced vibration in precision high speed routing spindles [J]. International Journal of Machine Tools and Manufacture, 2000,40(4): 561-577.

CHEN Y S, CHENG Y D, YANG T, et al. Accurate identification of the frequency response functions for the rotor bearing foundation system using the modified pseudo mode shape method [J]. Journal of Sound and Vibration, 2009, 329(6): 644-658.

PATEL V N, TANDON N, PANDEY R K. A dynamic model for vibration studies of deep groove ball bearings considering single and multiple defects in races [J]. Journal of Tribology, 2010, 132(4):1-10.

罗继伟,罗天宇.滚动轴承分析计算与应用 [M].北京:机械工业出版社,2009:205-207.

海伦.模态分析理论与实验 [M]. 白化同,郭继忠,译.北京:北京理工大学出版社,2001:143-180.

王福生,包钢.新型静压气体球轴承的超声速现象研究.2011,45(5):59-63.

宋学宾, 刘恒,易均,等.推力轴承对柔性转子系统的非线性动力影响.2011,45(9):108-113.

王福生,包钢.新型静压气体球轴承的超声速现象研究.2011,45(5):59-63.

马石磊,马求山,王琳,等.高速动静压轴承支承主轴系统动特性测试研究. 2011,45(5):52-58.

刘显军,洪军,朱永生,等.多支承轴系轴承受力与刚度的有限元迭代计算方法.2010,44(11):41-45.

范淑琴,赵升吨,张琦.直角法兰双辊夹持扩旋成形有限元模型的确定.2010,44(5):66-70.

孙振锋,齐乐华,舒扬,等.有限元方法的小管径单壁碳纳米管杨氏模量预测.2007,41(9):1066-1069.

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

往复式冰箱压缩机曲轴动态特性与轴承润滑计算分析

一种改进的局部倒频谱分析方法

采用符号时间序列分析的轴承早期微弱故障预警

多工况下离心压气机叶轮-机匣一体联合设计优化

融合物理信息与深度算子网络的变压器绕组热-流场快速计算方法