单螺杆压缩机增压槽道内喷液成膜特性研究

代泽宇; 邵华; 王增丽; 张建辉; 崔庆杰; 冯全科

doi:10.7652/xjtuxb202305009

您当前的位置：

首页 >

文章列表页 >

单螺杆压缩机增压槽道内喷液成膜特性研究

能源与动力 | 更新时间：2025-07-09

- 单螺杆压缩机增压槽道内喷液成膜特性研究
- Study on Film Formation Characteristics of Liquid Injected in Pressurized Channel of the Single Screw Compressor
- 西安交通大学学报 2023年57卷第5期页码：89-96
- 作者机构：
  
  1. 中国石油大学(华东)新能源学院,山东,青岛,266580
  2. 中国石油集团测井有限公司天津分公司,天津,300280
  3. 西安交通大学能源与动力工程学院,西安,710049
- 作者简介：
  
  : 2022-08-27。作者简介: 代泽宇(2000—),男,硕士生
  王增丽(通信作者),女,副教授。基金项目: 国家重点研发计划资助项目(2020YFB2010002)
- 基金信息：
  
  : 2022-08-27。作者简介: 代泽宇(2000—),男,硕士生;王增丽(通信作者),女,副教授。基金项目: 国家重点研发计划资助项目(2020YFB2010002);山东省自然科学基金资助项目(ZR2022ME114)。
- DOI：10.7652/xjtuxb202305009
  中图分类号： TH45
- 网络首发：2023-05-10，
  
  纸质出版：2023
- 稿件说明：
移动端阅览
代泽宇, 邵华, 王增丽, 等. 单螺杆压缩机增压槽道内喷液成膜特性研究[J]. 西安交通大学学报, 2023,57(5):89-96.

DAI Zeyu, SHAO Hua, WANG Zengli, et al. Study on Film Formation Characteristics of Liquid Injected in Pressurized Channel of the Single Screw Compressor[J]. 2023, 57(5): 89-96.
代泽宇, 邵华, 王增丽, 等. 单螺杆压缩机增压槽道内喷液成膜特性研究[J]. 西安交通大学学报, 2023,57(5):89-96. DOI： 10.7652/xjtuxb202305009.

DAI Zeyu, SHAO Hua, WANG Zengli, et al. Study on Film Formation Characteristics of Liquid Injected in Pressurized Channel of the Single Screw Compressor[J]. 2023, 57(5): 89-96. DOI： 10.7652/xjtuxb202305009.

摘要

为厘清单螺杆压缩机喷液压缩过程中喷入液体的运动状态、弥散分布和成膜铺展特性

实现喷液参数的合理调控

根据单螺杆压缩机基本结构和多圆柱复合包络啮合副空间啮合原理

建立了单条螺旋槽道的三维空间扭曲槽道模型

并依据螺旋槽道几何特征及啮合副相对运动关系对模型进行了简化。基于简化模型

利用计算流体动力学软件开展了喷液压缩过程中工作腔内部水气液两相流动过程的数值模拟研究

分析了变工况下喷入液体在增压槽道内的弥散分布和成膜特性以及介质压力和温度、螺杆转动速度、喷液流量和速度等关键运行参数对其影响规律。研究结果表明:喷入的液体在壁面上汇聚成膜

随着腔内压力的上升

形成液膜平均厚度呈下降趋势; 腔内温度自80 ℃上升到200 ℃

液膜平均厚度变化不大

上下波动范围在8.3%以内; 螺杆转子转速过快或者喷液速度过慢都会使得喷入液体还未接触壁面就被星轮撵出槽道

进而降低压缩过程的冷却效果; 喷液流量的增大将有效提升形成液膜的平均厚度

可以有效防止泄漏。

Abstract

This paper aims to clarify the motion state

dispersion distribution and film spreading characteristics of the liquid injected during the compression process of the single screw compressor

and realize the rational control of liquid injection parameters. A three-dimensional space-twisted groove model of a single spiral groove is established according to the basic structure of the single screw compressor and the spatial meshing principle of multicolumn envelope meshing pair. The model is simplified according to the geometric characteristics of the spiral groove and the relative motion relationship of the meshing pair. Based on the simplified model

the water-steam two-phase flow process in the working chamber is numerically simulated during the injected liquid compression process by using computational fluid dynamics software. Then

analysis is carried out on the dispersion distribution and film forming characteristics of the injected liquid in the pressurizing channel under variable working conditions

as well as on the influence of key operating parameters such as the medium pressure and temperature

screw rotation speed

liquid injection flow rate and speed. The results show that the injected liquid converges on the wall to form a film

and the average thickness of the formed film decreases with the increase of pressure. When the temperature in the cavity rises from 80 ℃ to 200 ℃

the average thickness of the liquid film does not change much

i.e. fluctuating within 8.3%. If the rotating speed of the screw rotor is too high or the liquid spraying speed is too low

the injected liquid will be driven out of the channel by the star wheel before reaching the wall

thus reducing the cooling effect in the compression process. The average thickness of the liquid film can be effectively improved by increasing the spray liquid flow rate

which can effectively prevent leakage.

关键词

Keywords

references

LIU Changchun, HAN Wei, XUE Xiaodong. Experimental investigation of a high-temperature heat pump for industrial steam production [J]. Applied Energy, 2022, 312: 118719.

何永宁, 杨东方, 曹锋, 等. 补气技术应用于高温热泵的实验研究 [J]. 西安交通大学学报, 2015, 49(6): 103-108.

HE Yongning, YANG Dongfang, CAO Feng, et al. Experimental investigation on vapor injection in high temperature heat pump [J]. Journal of Xi'an Jiaotong University, 2015, 49(6): 103-108.

GAUR A S, FITIWI D Z, CURTIS J. Heat pumps and our low-carbon future: a comprehensive review [J]. Energy Research Social Science, 2021, 71: 101764.

张建军, 李帅旗, 陈永珍, 等. 蒸汽再压缩技术研究现状与发展趋势 [J]. 新能源进展, 2020, 8(3): 207-215.

ZHANG Jianjun, LI Shuaiqi, CHEN Yongzhen, et al. Overview and development tendency of steam recompression [J]. Advances in New and Renewable Energy, 2020, 8(3): 207-215.

WU Weifeng, ZHANG Zhao. Development of single screw compressor technologies and their tendency [J]. Proceedings of the Institution of Mechanical Engineers: Part E Journal of Process Mechanical Engineering, 2022, 236(2): 738-751.

彭程宇, 张瞾, 谢佳, 等. 单螺杆压缩机转子异步压缩循环的动力学分析 [J]. 西安交通大学学报, 2021, 55(1): 136-144.

PENG Chengyu, ZHANG Zhao, XIE Jia, et al. Dynamic analysis of the asynchronous compression cycle for the rotor in single screw compressor [J]. Journal of Xi'an Jiaotong University, 2021, 55(1): 136-144.

李亚南, 王景甫, 吴玉庭, 等. 水润滑单螺杆空气压缩机喷水雾化的理论分析及仿真 [J]. 北京工业大学学报, 2022, 48(5): 552-560.

LI Yanan, WANG Jingfu, WU Yuting, et al. Theoretical analysis and simulation on water injection atomization of water-lubricated single screw compressor [J]. Journal of Beijing University of Technology, 2022, 48(5): 552-560.

WEN Qiangyu, ZHI Ruiping, WU Yuting, et al. Performance optimization of a heat pump integrated with a single-screw refrigeration compressor with liquid refrigerant injection [J]. Energy, 2020, 207: 118197.

WANG Baolong, SHI Wenxing, LI Xianting, et al. Numerical research on the scroll compressor with refrigeration injection [J]. Applied Thermal Engineering, 2008, 28(5/6): 440-449.

DUTTA A K, YANAGISAWA T, FUKUTA M. A study on compression characteristic of wet vapor refrigerant [C]//International Compressor Engineering Conference. West Lafayette, IN, USA: Purdue University, 1996: 235-240.

YANG Shengmei, OUYANG Hua, WU Yadong, et al. CFD simulation for the internal pressure characteristics of an oil-injected twin-screw refrigeration compressor [J]. International Journal of Refrigeration, 2021, 126: 143-154.

吴华根, 唐昊, 王养浩, 等. 间隙对双螺杆制冷压缩机性能的影响 [J]. 西安交通大学学报, 2015, 49(2): 130-134.

WU Huagen, TANG Hao, WANG Yanghao, et al. Clearance effects on performance of twin screw refrigeration compressor [J]. Journal of Xi'an Jiaotong University, 2015, 49(2): 130-134.

LIU Z, SOEDEL W. An investigation of compressor slugging problems [C]//International Compressor Engineering Conference. West Lafayette, IN, USA: Purdue University, 1994: 433-440.

DUTTA A K, YANAGISAWA T, FUKUTA M. An investigation of the performance of a scroll compressor under liquid refrigerant injection [J]. International Journal of Refrigeration, 2001, 24(6): 577-587.

JEON Y, LEE S H, KIM W, et al. Numerical study on the optimal design of injection-hole geometries of a twin rotary compressor in a liquid injection heat pump [J]. Applied Thermal Engineering, 2017, 113: 1178-1188.

WANG Zengli, SHEN Yingfeng, WANG Zhenbo, et al. Theoretical research and optimization analysis for the injection process of the single screw refrigeration compressor [J]. International Journal of Refrigeration, 2018, 88: 91-101.

ZHAO Bin, SONG Haoyang, GAO Diankui, et al. Flow and heat transfer coupling analysis of oil-gas two-phase fluid in clearance of single screw compressor based on fuzzy curvelet finite element method [J]. Case Studies in Thermal Engineering, 2020, 22: 100788.

黄锐, 夏天, 陈国庆, 等. 单螺杆压缩机啮合副油膜流场数学模型研究 [J]. 西安理工大学学报, 2022, 38(2): 185-193.

HUANG Rui, XIA Tian, CHEN Guoqing, et al. Study of oil film flow field simulation models in meshing pairs for single screw compressor [J]. Journal of Xi'an University of Technology, 2022, 38(2): 185-193.[20] 宁新杰. CP型单螺杆压缩机关键技术研究及内流场模拟 [D]. 湘潭: 湘潭大学, 2012.

周雷, 金光熹. 喷液单螺杆压缩机内液滴运动规律及其对传热的影响 [J]. 流体机械, 1998, 26(6): 3-7.

ZHOU Lei, JIN Guangxi. Droplet movement and its influence on heat transfer in a liquid injection single screw compressor [J]. Fluid Machinery, 1998, 26(6): 3-7.

李红旗, 金光熹, 吴业正. 喷油单螺杆压缩机转子螺槽表面温度的测量 [J]. 流体工程, 1993, 21(12): 5-8, 63.

LI Hongqi, JIN Guangxi, WU Yezheng. Surface temperature measurement of grooves of oil-flooded single screw compressors [J]. Fluid Engineering, 1993, 21(12): 5-8, 63.

HISHIKI T, NAKAMURA S, AMANO Y, et al. Experiment and analysis of two-phase compression in a rocking type steam compressor [J]. Transactions of the Japan Society of Mechanical Engineers: Series B, 2013, 79(808): 2826-2835.

吴修闻, 李军, 陈焕新, 等. 螺杆压缩机喷油参数的理论分析与仿真研究 [J]. 压缩机技术, 2011(2): 1-4, 20.

WU Xiuwen, LI Jun, CHEN Huanxin, et al. Theoretical analysis and simulation research on oil injection parameters of screw compressor [J]. Compressor Technology, 2011(2): 1-4, 20.

林强, 樊灵, 金光喜. 单螺杆压缩机喷油雾化的理论分析和实验研究 [J]. 西安石油学院学报(自然科学版), 2000, 15(2): 41-44.

LIN Qiang, FAN Ling, JIN Guangxi. Theoretical analysis and experimental study of oil atomizing in a single screw compressor [J]. Journal of Xi'an Petroleum Institute(Natural Science Edition), 2000, 15(2): 41-44.

王增丽, 申迎峰, 王振波, 等. 单螺杆压缩机工作腔喷液过程几何特性及工作机理研究 [J]. 西安交通大学学报, 2017, 51(2): 128-134.

WANG Zengli, SHEN Yingfeng, WANG Zhenbo, et al. Geometric characteristic and working mechanism of injection process in single screw compressor with injection [J]. Journal of Xi'an Jiaotong University, 2017, 51(2): 128-134.

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

液压圆柱滑阀K-K型节流槽流量面积参数模型

吸气喷液对空气源热泵热水器性能的影响

富氧燃烧对柴油机低温燃烧反应机理影响的数值分析

水平轴潮汐透平场的数值研究

喷水推进泵压力脉动特性数值计算及分析