考虑确定性表面形貌的O形圈密封性能分析

和建森; 翟黎明; 饶聪; 黄毅杰; 郭飞

doi:10.7652/xjtuxb202212005

您当前的位置：

首页 >

文章列表页 >

考虑确定性表面形貌的O形圈密封性能分析

专题 ICFPMCE 2022国际会议(续) | 更新时间：2025-07-09

- 考虑确定性表面形貌的O形圈密封性能分析
- Analysis of O-Ring Sealing Performance Considering Deterministic Surface Topography
- 西安交通大学学报 2022年56卷第12期页码：46-55
- 作者机构：
  
  1. 中国民航大学航空工程学院,天津,300300
  2. 清华大学摩擦学国家重点实验室,北京,100084
  3. 一汽解放汽车有限公司发动机事业部,江苏,无锡,214000
- 作者简介：
  
  : 2022-03-10。作者简介: 和建森(1998—),男,硕士生
  郭飞(通信作者),男,助理研究员。基金项目: 国家自然科学基金资助项目(U1937602)
- 基金信息：
  
  : 2022-03-10。作者简介: 和建森(1998—),男,硕士生;郭飞(通信作者),男,助理研究员。基金项目: 国家自然科学基金资助项目(U1937602);航空科学基金资助项目(201907058001)
- DOI：10.7652/xjtuxb202212005
  中图分类号： TB42
- 网络首发：2022-12-10，
  
  纸质出版：2022
- 稿件说明：
移动端阅览
和建森, 翟黎明, 饶聪, 等. 考虑确定性表面形貌的O形圈密封性能分析[J]. 西安交通大学学报, 2022,56(12):46-55.

HE Jiansen, ZHAI Liming, RAO Cong, et al. Analysis of O-Ring Sealing Performance Considering Deterministic Surface Topography[J]. 2022, 56(12): 46-55.
和建森, 翟黎明, 饶聪, 等. 考虑确定性表面形貌的O形圈密封性能分析[J]. 西安交通大学学报, 2022,56(12):46-55. DOI： 10.7652/xjtuxb202212005.

HE Jiansen, ZHAI Liming, RAO Cong, et al. Analysis of O-Ring Sealing Performance Considering Deterministic Surface Topography[J]. 2022, 56(12): 46-55. DOI： 10.7652/xjtuxb202212005.

摘要

为测量O形密封圈应用在负压油介质环境中的密封泄漏率

构建了一套求解O形密封圈泄漏率的数值仿真算法

并辅以实验进行验证。利用真实表面形貌进行分区处理用于匹配接触压力分布

进而利用接触状态矩阵生成泄漏通道来模拟真实泄漏状况

通过观察泄漏通道的有无来判定密封是否泄漏

同时对平行平板泄漏模型进行改进使其适用于不同通道截面形状的泄漏率计算。对不同油压下的O形圈密封泄漏率进行计算

结果表明:当流体介质压力为0.07 MPa时

仿真所得密封泄漏率为1.717×10

-12

/s; 当介质压力增大至0.09 MPa时

仿真所得密封泄漏率下降为1.525×10

-12

/s。比较不同介质压力下的接触应力分布

结果表明:随流体介质压力增加

密封接触区域接触应力分布增大

形成贯穿密封接触区域的泄漏通道范围减小

泄漏率减小。为验证仿真结果的合理性

将仿真结果与实验结果进行对比

结果表明:两者相对误差在10%左右

实验结果与仿真结果相符程度较好。

Abstract

This paper proposes a set of numerical simulation algorithms to measure the leakage rate of O-ring in negative pressure oil medium. To be specific

a partition algorithm based on real surface topography is first used to match the contact pressure distribution. Then a contact state matrix is used to generate leak paths to simulate real conditions and determine seal leakage. Moreover

the parallel plate leak model is improved to make it applicable to the calculation of leakage rate of channel cross sections in different shapes. The leakage

rates of the O-ring under different oil pressures are calculated. According to the results

when the fluid medium pressure is 0.07 MPa

the seal leakage rate obtained by simulation is 1.717×10

-12

/s; when the fluid medium pressure increases to 0.09 MPa

the seal leakage rate obtained by simulation decreases to 1.525×10

-12

/s. The contact stress distributions under different medium pressures are compared. According to the results

with the increase of fluid medium pressure

the contact stress distribution in the seal contact area increases

the leakage paths formed through the sealing contact area decreases and the leakage rate drops. Finally

the simulation results are compared with the experimental results to verify their rationality. The results show that the relative error is about 10%

and the experimental results are in good agreement with the simulation results.

关键词

Keywords

references

蔡仁良. 流体密封技术 [M]. 北京: 化学工业出版社, 2013.

陈志, 高钰, 董蓉, 等. 机械密封橡胶O形圈密封性能的有限元分析 [J]. 四川大学学报(工程科学版), 2011, 43(5): 234-239.

CHEN Zhi, GAO Yu, DONG Rong, et al. Finite element analysis of sealing characteristics of the rubber O-ring for a mechanical seal [J]. Journal of Sichuan University(Engineering Science Edition), 2011, 43(5): 234-239.

关文锦, 杜群贵, 刘丕群. 橡胶O形圈密封性能的有限元分析 [J]. 润滑与密封, 2012, 37(6): 60-64.

GUAN Wenjin, DU Qungui, LIU Piqun. Finite element analysis of the sealing performance of rubber O-ring [J]. Lubrication Engineering, 2012, 37(6): 60-64.

郭志强, 门日秀, 闫柯, 等. 涡轮增压器甩油环密封性能研究 [J]. 西安交通大学学报, 2019, 53(10): 143-150.

GUO Zhiqiang, MEN Rixiu, YAN Ke, et al. Sealing performance of turbocharger oil slinger [J]. Journal of Xi'an Jiaotong University, 2019, 53(10): 143-150.

陆婷婷, 王维民, 陈立芳. 橡胶黏弹性对橡胶O形圈密封性能的影响 [J]. 北京化工大学学报(自然科学版), 2014, 41(6): 93-97.

LU Tingting, WANG Weimin, CHEN Lifang. A study of the performance of an O-ring seal with viscoelasticity [J]. Journal of Beijing University of Chemical Technology(Natural Science Edition), 2014, 41(6): 93-97.

张镇国, 沙宝林, 王才, 等. 基于Abaqus的往复运动中双道O型圈密封性能分析 [J]. 固体火箭技术, 2019, 42(1): 85-91.

ZHANG Zhenguo, SHA Baolin, WANG Cai, et al. Analysis of the double-sealing performance of O-ring in reciprocating movement based on Abaqus [J]. Journal of Solid Rocket Technology, 2019, 42(1): 85-91.

AKULICHEV A G, ECHTERMEYER A T, PERSSON B N J. Interfacial leakage of elastomer seals at low temperatures [J]. International Journal of Pressure Vessels and Piping, 2018, 160: 14-23.

ALBRECHT D, ACHENBACH M. Seals for high-pressure tank systems in fuel cell cars [J]. KGK Rubberpoint, 2014, 67(2): 12-17.

王广振, 季林红, 温诗铸, 等. 空间O型圈密封泄漏率实验研究 [J]. 空间科学学报, 2001, 21(4): 363-369.

WANG Guangzhen, JI Linhong, WEN Shizhu, et al. Experimental research on leakage rate of space seal with O-ring [J]. Chinese Journal of Space Science, 2001, 21(4): 363-369.

GEORGE A F, STROZZI A, RICH J I. Stress fields in a compressed unconstrained elastomeric O-ring seal and a comparison of computer predictions and experimental results [J]. Tribology International, 1987, 20(5): 237-247.

PERSSON B N J, ALBOHR O, CRETON C, et al. Contact area between a viscoelastic solid and a hard, randomly rough, substrate [J]. The Journal of Chemical Physics, 2004, 120(18): 8779-8793.

PERSSON B N J, ALBOHR O, TARTAGLINO U, et al. On the nature of surface roughness with application to contact mechanics, sealing, rubber friction and adhesion [J]. Journal of Physics: Condensed Matter, 2005, 17(1): R1-R62.

PERSSON B N J, YANG C. Theory of the leak-rate of seals [J]. Journal of Physics: Condensed Matter, 2008, 20(31): 315011.

LORENZ B, PERSSON B N J. Leak rate of seals: comparison of theory with experiment [J]. Europhysics Letters, 2009, 86(4): 44006.

LORENZ B, PERSSON B N J. On the dependence of the leak rate of seals on the skewness of the surface height probability distribution [J]. Europhysics Letters, 2010, 90(3): 38002.

张元桥, 李军, 马登骞, 等. 螺旋篦齿-刷式密封泄漏特性实验和数值研究 [J]. 西安交通大学学报, 2020, 54(11): 1-9.

ZHANG Yuanqiao, LI Jun, MA Dengqian, et al. Experimental and numerical investigations on the leakage flow characteristics of helical-labyrinth-brush seals [J]. Journal of Xi'an Jiaotong University, 2020, 54(11): 1-9.

BOTTIGLIONE F, CARBONE G, MANTRIOTA G. Fluid leakage in seals: an approach based on percolation theory [J]. Tribology International, 2009, 42(5): 731-737.

BOTTIGLIONE F, CARBONE G, MANGIALARDI L, et al. Leakage mechanism in flat seals [J]. Journal of Applied Physics, 2009, 106(10): 104902.

DAPP W B, LÜCKE A, PERSSON B N J, et al. Self-affine elastic contacts: percolation and leakage [J]. Physical Review Letters, 2012, 108(24): 244301.

WEBSTER M N, SAYLES R S. A numerical model for the elastic frictionless contact of real rough surfaces [J]. Journal of Tribology, 1986, 108(3): 314-320.

JU Yongqing, ZHENG Linqing. A full numerical solution for the elastic contact of three-dimensional real rough surfaces [J]. Wear, 1992, 157(1): 151-161.

STANLEY H M, KATO T. An FFT-based method for rough surface contact [J]. Journal of Tribology, 1997, 119(3): 481-485.

WESTERGAARD H M. Bearing pressures and cracks: bearing pressures through a slightly waved surface or through a nearly flat part of a cylinder, and related problems of cracks [J]. Journal of Applied Mechanics, 1939, 6(2): A49-A53.

JOHNSON K L, GREENWOOD J A, HIGGINSON J G. The contact of elastic regular wavy surfaces [J]. International Journal of Mechanical Sciences, 1985, 27(6): 383-396.

史建成. 基于逾渗理论的静密封建模方法与泄漏机理研究 [D]. 北京: 北京理工大学, 2015.

XU Yang. An analysis of elastic rough contact models [D]. Auburn: Auburn University, 2012.

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

电动车辆间接热系统快速除湿响应迟滞机理及优化控制策略

张角凹坑气膜孔对双层壁气膜冷却特性的影响

采用试验设计方法的第三代CO2气体箔轴承箔片几何参数敏感性分析

扇贝仿生密封腔室内超临界二氧化碳泄漏流湍动能耗散机理研究

不同板叠材料热声热机能量转换过程数值模拟研究