气膜抽吸与叶片前缘内部壁面射流的作用机制

邓清华; 王辉辉; 何伟; 丰镇平

doi:10.7652/xjtuxb202210016

您当前的位置：

首页 >

文章列表页 >

气膜抽吸与叶片前缘内部壁面射流的作用机制

—————————————————————— | 更新时间：2025-07-09

- 气膜抽吸与叶片前缘内部壁面射流的作用机制
- Mechanism of Action Between Film Suction and Wall Jet in Leading Edge of Blades
- 西安交通大学学报 2022年56卷第10期页码：160-169
- 作者机构：
  
  西安交通大学能源与动力工程学院,西安,710049
- 作者简介：
  
  : 2022-01-27。作者简介: 邓清华(1975—),男,博士,副教授,博士生导师。基金项目: 两机重大专项资助项目(J2019-Ⅱ-0008-0028)
- 基金信息：
  
  : 2022-01-27。作者简介: 邓清华(1975—),男,博士,副教授,博士生导师。基金项目: 两机重大专项资助项目(J2019-Ⅱ-0008-0028)
- DOI：10.7652/xjtuxb202210016
  中图分类号： TK474.7
- 网络首发：2022-10-10，
  
  纸质出版：2022
- 稿件说明：
移动端阅览
邓清华, 王辉辉, 何伟, 等. 气膜抽吸与叶片前缘内部壁面射流的作用机制[J]. 西安交通大学学报, 2022,56(10):160-169.

DENG Qinghua, WANG Huihui, HE Wei, et al. Mechanism of Action Between Film Suction and Wall Jet in Leading Edge of Blades[J]. 2022, 56(10): 160-169.
邓清华, 王辉辉, 何伟, 等. 气膜抽吸与叶片前缘内部壁面射流的作用机制[J]. 西安交通大学学报, 2022,56(10):160-169. DOI： 10.7652/xjtuxb202210016.

DENG Qinghua, WANG Huihui, HE Wei, et al. Mechanism of Action Between Film Suction and Wall Jet in Leading Edge of Blades[J]. 2022, 56(10): 160-169. DOI： 10.7652/xjtuxb202210016.

摘要

为揭示气膜抽吸对壁面射流流动与换热的干涉效应

获得壁面射流冷却通道内的流动特性与换热特性

建立了涡轮叶片前缘带气膜抽吸的单通道壁面射流冷却计算模型。采用RANS方法

结合SST k-ω湍流模型

研究了气膜抽吸、射流雷诺数、气膜孔位置和数量等因素对壁面射流内部冷却特性的影响机制。结果表明:气膜抽吸会大幅提高流动结构的稳定性

气膜孔入口的分离涡则会显著提高孔口附近的换热系数; 气膜抽吸引起壁面射流流量的降低不利于靶面下游的冷却

但滞止区和通道内的流动损失降低幅度大于气膜孔内的掺混损失

从而使整体流动损失系数降低了4.5%; 射流雷诺数的增加会提高换热强度

但对流动结构几乎没有影响; 单孔结构中

在前缘滞止线处开孔能够提供最高的气膜流量比

且对前缘内部靶面的冷却效果良好; 多孔结构中

双气膜孔结构的流动损失最大

三气膜孔结构的流动损失和换热强度最为均衡。研究结果可为壁面射流冷却结构的气膜孔布置提供依据

为进一步提高壁面射流冷却结构的冷却效果提供参考。

Abstract

The computational models of single-channel wall jet cooling with film suction are established at the leading edge of turbine blades in this paper to reveal the interference effect of film suction on the flow and heat transfer of wall jet and obtain the flow and heat transfer characteristics in the wall jet cooling channel. The RANS method with SST k-ω turbulence model is adopted to research the effects of film suction

jet Reynolds number

film hole position

number and other factors on the internal cooling characteristics of wall jet. The results show that film suction can significantly improve the stability of flow structures. The heat transfer coefficient near the inlet of film hole can be raised notably by the separation vortex. The decreased mass flow rate of the wall jet brought from the film suction is not conductive to the cooling of the downstream target. However

the decreasing level of flow loss at the stagnation area and channel is larger than the mixing loss in film hole

thereby reducing the overall flow loss coefficient by 4.5%. With the increase of the Reynolds number

the heat transfer intensity will improve

which

however

has little effect on the flow structure. Among the structures with a single film hole

the opening at the position of the leading edge stagnation line can provide the highest film flow ratio and has a good cooling effect on the target surface inside the leading edge. Among the structures with multiple holes

the structure with double film holes has the largest flow loss

and the structure with three film holes has the most balanced flow loss and heat transfer intensity. The research results provide a basis for the arrangement of film holes for the wall jet cooling structure

and provide a reference for further improvement of the cooling effect.

关键词

Keywords

references

LUAN Yigang, BU Shi, SUN Haiou, et al. Numerical investigation on flow and heat transfer in matrix cooling channels for turbine blades [C]//ASME Turbo Expo 2016: Turbomachinery Technical Conference and Exposition. New York, NY, USA: ASME, 2016: V05BT11A005.

董志国, 王鸣, 李晓欣, 等. 航空发动机涡轮叶片材料的应用与发展 [J]. 钢铁研究学报, 2011, 23(S2): 455-457.

DONG Zhiguo, WANG Ming, LI Xiaoxin, et al. Application and progress of materials for turbine blade of aeroengine [J]. Journal of Iron and Steel Research, 2011, 23(S2):455-457.

GOLDSTEIN R J, BEHBAHANI A I, HEPPELMANN K K. Streamwise distribution of the recovery factor and the local heat transfer coefficient to an impinging circular air jet [J]. International Journal of Heat and Mass Transfer, 1986, 29(8): 1227-1235.

METZGER D E, YAMASHITA T, JENKINS C W. Impingement cooling of concave surfaces with lines of circular air jets [J]. Journal of Engineering for Power, 1969, 91(3): 149-155.

TASLIM M E, BAKHTARI K, LIU H. Experimental and numerical investigation of impingement on a rib-roughened leading-edge wall [J]. Journal of Turbomachinery, 2003, 125(4): 682-691.

刘钊, 丰镇平, 宋立明. 实际叶片前缘冲击冷却流动和换热的数值研究 [J]. 西安交通大学学报, 2011, 45(1): 5-9, 20.

LIU Zhao, FENG Zhenping, SONG Liming. Numerical study on flow and heat transfer of impingement cooling on leading edge of actual turbine blade [J]. Journal of Xi'an Jiaotong University, 2011, 45(1): 5-9, 20.

迟重然. 燃气轮机透平冷却结构作用机制与设计优化方法 [D]. 北京: 清华大学, 2014.

METZGER D E, KORSTAD R J. Effects of crossflow on impingement heat transfer [J]. Journal of Engineering for Power, 1972, 94(1): 35-41.

GOLDSTEIN R J, BEHBAHANI A I. Impingement of a circular jet with and without cross flow [J]. International Journal of Heat and Mass Transfer, 1982, 25(9): 1377-1382.

FLORSCHUETZ L W, METZGER D E, SU C C. Heat transfer characteristics for jet array impingement with initial crossflow [J]. Journal of Heat Transfer, 1984, 106(1): 34-41.

TASLIM M E, BETHKA D. Experimental and numerical impingement heat transfer in an airfoil leading-edge cooling channel with cross-flow [J]. Journal of Turbomachinery, 2009, 131(1): 011021.

XING Yunfei, SPRING S, WEIGAND B. Experimental and numerical investigation of impingement heat transfer on a flat and micro-rib roughened plate with different crossflow schemes [J]. International Journal of Thermal Sciences, 2011, 50(7): 1293-1307.

CALISKAN S, BASKAYA S. Experimental investigation of impinging jet array heat transfer from a surface with V-shaped and convergent-divergent ribs [J]. International Journal of Thermal Sciences, 2012, 59: 234-246.

CHEN Lingling, BRAKMANN R G A, WEIGAND B, et al. Experimental and numerical heat transfer investigation of an impingement jet array with V-ribs on the target plate and on the impingement plate [J]. International Journal of Heat and Fluid Flow. 2017, 68: 126-138.

GLEZER B, MOON H K, O'CONNELL T. A novel technique for the internal blade cooling [C]//ASME 1996 International Gas Turbine and Aeroengine Congress and Exhibition. New York, NY, USA: ASME, 1996: V004T09A015.

LIGRANI P M, HEDLUND C R, BABINCHAK B T, et al. Flow phenomena in swirl chambers [J]. Experiments in Fluids, 1998, 24(3): 254-264.

MOON H K. O'CONNELL T, GLEZER B. Heat transfer enhancement in a circular channel using lengthwise continuous tangential injection [C]//Proceedings of the 11th International Heat Transfer Conference. Danbury, CT, USA: Begell House, 1998: 559-564.

周源远, 范小军, 李亮, 等. 燃气轮机叶片前缘旋流冷却的热流固耦合数值研究 [J]. 西安交通大学学报, 2020, 54(1): 135-142.

ZHOU Yuanyuan, FAN Xiaojun, LI Liang, et al. Numerical research on the swirl cooling using thermal-fluid-structure coupled method for turbine blade leading edge [J]. Journal of Xi'an Jiaotong University, 2020, 54(1): 135-142.

KUSTERER K, LIN Gang, BOHN D, et al. Heat transfer enhancement for gas turbine internal cooling by application of double swirl cooling chambers [C]//ASME Turbo Expo 2013: Turbine Technical Conference and Exposition. New York, NY, USA: ASME, 2013: V03AT12A027.

KUSTERER K, LIN Gang, BOHN D, et al. Leading edge cooling of a gas turbine blade with double swirl chambers [C]//ASME Turbo Expo 2014: Turbine Technical Conference and Exposition. New York, NY, USA: ASME, 2014: V05AT12A024.

ZHANG Luzeng, YIN Juan, MOON H K. Airfoil for turbomachine and airfoil cooling method: USA 2017/0248022A1 [P]. 2017-08-31.

HE Wei, DENG Qinghua, HE Juan, et al. Effects of jetting orifice geometry parameters and channel Reynolds number on bended channel cooling for a novel internal cooling structure [C]//ASME Turbo Expo 2019: Turbomachinery Technical Conference and Exposition. New York, NY, USA: ASME, 2019: V05AT11A005.

HE Wei, DENG Qinghua, YANG Guoying, et al. Effects of turning angle and turning internal radius on channel impingement cooling for a novel internal cooling structure [J]. Journal of Turbomachinery, 2021, 143(9): 091005.

XING Yunfei, SPRING S, WEIGAND B. Experimental and numerical investigation of heat transfer characteristics of inline and staggered arrays of impinging jets [J]. Journal of Heat Transfer, 2010, 132(9): 53-58.

LING J P C W, IRELAND P T, HARVEY N W. Measurement of heat transfer coefficient distributions and flow field in a model of a turbine blade cooling passage with tangential injection [C]//ASME Turbo Expo 2006: Power for Land, Sea, and Air. New York, NY, USA: ASME, 2006: 325-340.

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

张角凹坑气膜孔对双层壁气膜冷却特性的影响

液氢管路输运中静电积聚机理与电流密度分布特征研究

X射线辐照下聚酰亚胺材料空间电荷分布特性的数值模拟

异质裂隙内超临界CO2地热提取特性数值模拟研究

带锥形孔的矩阵冷却通道流动换热多目标优化