压力侧冷却流对凹槽叶顶气膜冷却与传热性能的影响

于金杏; 叶明亮; 何坤; 晏鑫

doi:10.7652/xjtuxb202203016

您当前的位置：

首页 >

文章列表页 >

压力侧冷却流对凹槽叶顶气膜冷却与传热性能的影响

更新时间：2025-07-09

- 压力侧冷却流对凹槽叶顶气膜冷却与传热性能的影响
- Effect of Pressure-Side Cooling Flow on Film Cooling and Heat Transfer Performance at Squealer Tip
- 西安交通大学学报 2022年56卷第3期页码：160-172
- 作者机构：
  
  西安交通大学能源与动力工程学院,西安,710049
- 作者简介：
  
  晏鑫(通信作者),男,教授,博士生导师。基金项目: 国家自然科学基金资助项目(52076165)
- 基金信息：
  
  : 2021-09-05。作者简介: 于金杏(1996—),女,硕士生;晏鑫(通信作者),男,教授,博士生导师。基金项目: 国家自然科学基金资助项目(52076165)
- DOI：10.7652/xjtuxb202203016
  中图分类号： TK474.7
- 网络首发：2022-03-10，
  
  纸质出版：2022
- 稿件说明：
移动端阅览
于金杏, 叶明亮, 何坤, 等. 压力侧冷却流对凹槽叶顶气膜冷却与传热性能的影响[J]. 西安交通大学学报, 2022,56(3):160-172.

Effect of Pressure-Side Cooling Flow on Film Cooling and Heat Transfer Performance at Squealer Tip[J]. 2022, 56(3): 160-172.
于金杏, 叶明亮, 何坤, 等. 压力侧冷却流对凹槽叶顶气膜冷却与传热性能的影响[J]. 西安交通大学学报, 2022,56(3):160-172. DOI： 10.7652/xjtuxb202203016.

Effect of Pressure-Side Cooling Flow on Film Cooling and Heat Transfer Performance at Squealer Tip[J]. 2022, 56(3): 160-172. DOI： 10.7652/xjtuxb202203016.

摘要

为了降低凹槽叶顶整体热负荷并提高高传热区的气膜冷却效率

研究了压力侧冷却射流对透平级凹槽叶顶冷却传热性能的影响。通过数值计算获得了2种压力侧气膜孔形状(圆孔、扩张孔)和5种压力侧射流角(20°～40°)条件下

透平级凹槽叶顶的传热系数和气膜冷却效率分布。研究表明:前缘压力侧冷却流进入凹槽

增强了凹槽底部的冷却效果; 中部和尾缘压力侧冷却流对凹槽肩壁和叶顶尾缘进行了冷却

增强了叶顶高热负荷区域的冷却效果。在所研究的射流角范围内

射流角越小

凹槽叶顶的冷却效果越好。当采用扩张孔、射流角由20°增大到40°时

肩壁的面积平均传热系数增大了6%

面积平均气膜冷却效率减小了14.3%; 叶顶压力侧的面积平均传热系数增大了36%

面积平均气膜冷却效率减小了37.2%。在小射流角条件下

扩张孔的叶顶和压力侧冷却效果优于圆孔。射流角为20°时

与圆孔相比:扩张孔使凹槽肩壁面积平均传热系数减小了2%

面积平均气膜冷却效率增大了5.9%; 扩张孔使叶顶压力侧的面积平均传热系数减小了22.6%

面积平均气膜冷却效率增大了43.3%。

Abstract

To reduce the overall thermal load at squealer tip and improve the film cooling effectiveness in high heat transfer areas

the influence of pressure-side coolant jet flow on heat transfer and film cooling performance of squealer tip in a turbine stage was investigated. The heat transfer coefficient and film cooling effectiveness at squealer tip with two kinds of cooling hole shapes(i.e.cylindrical and fan-shaped holes)and five different jet ejection angles(20°-40°)for pressure-side cooling holes were obtained through numerical simulations. The results show that the pressure-side cooling flow enters the cavity near the leading edge

improving the cooling effect on the cavity floor. The pressure-side coolant from the middle chord and near the trailing edge holes forms the cooling film on the tip surface and at the tip trailing edge

which enhances the cooling performance in the tip's high thermal load area. In the present study

the cooling effect on squealer tip is increased with the decrease of ejection angle. For the fan-shaped holes at squealer tip

the area-averaged heat transfer coefficient is increased by 6% and the area-averaged film cooling effectiveness is decreased by 14.3% on the squealer rim

whereas the area-averaged heat transfer coefficient is increased by 36% and the area-averaged film cooling effectiveness is decreased by 37.2% in the tip pressure-side region

as the jet ejection angle increases from 20° to 40°. With small jet ejection angle

the film cooling effect on the squealer tip and pressure-side surface for the fan-shaped holes is better than that of cylindrical holes. If the jet ejection angle is fixed at 20°

the fan-shaped holes are able to decrease the heat transfer coefficient by 2% while increase the film cooling effectiveness by 5.9% on the tip surface

and decrease the heat transfer coefficient by 22.6% while increase the film cooling effectiveness by 43.3% on the pressure-side surface

as compared with the cylindrical holes.

关键词

Keywords

references

BUNKER R S. Axial turbine blade tips: function, design, and durability [J]. Journal of Propulsion and Power, 2006, 22(2): 271-285.

KIM J H, LEE S Y, CHUNG J T. Numerical analysis of the aerodynamic performance heat transfer of a transonic turbine with a partial squealer tip [J]. Applied Thermal Engineering, 2019, 152: 878-889.

YAN Xin, YE Mingliang, HE Kun. Investigations into heat transfer and aerodynamic performance of a worn squealer tipped turbine stage [J]. Journal of Turbomachinery, 2020, 142(9): 091012.

KWAK J S, HAN J C. Heat transfer coefficients on the squealer tip and near squealer tip regions of a gas turbine blade [J]. Journal of Heat Transfer, 2003, 125(4): 669-677.

ZHU D, LU S, MA H, et al. Rotating effect on transonic squealer tip cooling performance [C]∥ASME Turbo Expo 2017: Turbomachinery Technical Conference and Exposition. New York, USA: ASME, 2017: V05AT12A014.

CHENG Fengna, ZHANG Jingzhou, CHANG Haiping, et al. Investigations of film-cooling effectiveness on the squealer tip with various film-hole configurations in a linear cascade [J]. International Journal of Heat and Mass Transfer, 2018, 117: 344-357.

肖东, 李琛玺, 宋立明, 等. 凹槽深度及吹风比的不确定性对动叶叶顶冷却特性影响研究 [J]. 工程热物理学报, 2020, 41(7): 1627-1634.

XIAO Dong, LI Chenxi, SONG Liming, et al. Influence of uncertainties arising from squealer depth and blowing ratio on cooling characteristics of rotor tips [J]. Journal of Engineering Thermophysics, 2020, 41(7): 1627-1634.

张玲, 董宇航, 李婷婷. 燃气轮机涡轮动叶顶部气动与传热特性的数值研究 [J]. 燃气涡轮试验与研究, 2017, 30(6): 12-18, 42.

ZHANG Ling, DONG Yuhang, LI Tingting. Numerical investigation on aerodynamic performance and heat transfer of rotor tip in gas turbine [J]. Gas Turbine Experiment and Research, 2017, 30(6): 12-18, 42.

黄琰, 晏鑫, 何坤, 等. 气膜孔分布对凹槽叶顶传热和冷却性能的影响 [J]. 西安交通大学学报, 2016, 50(5): 101-107.

HUANG Yan, YAN Xin, HE Kun, et al. Effect of cooling-hole distributions on heat transfer and cooling effectiveness on turbine blade tip [J]. Journal of Xi'an Jiaotong University, 2016, 50(5): 101-107.

KIM Y W, DOWNS J P, SOECHTING F O, et al. Darryl E. Metzger Memorial Session Paper: a summary of the cooled turbine blade tip heat transfer and film effectiveness investigations performed by Dr. D. E. Metzger [J]. Journal of Turbomachinery, 1995, 117(1): 1-11.

NASIR H, EKKAD S V, BUNKER R S. Effect of tip and pressure side coolant injection on heat transfer distributions for a plane and recessed tip [J]. Journal of Turbomachinery, 2007, 129(1): 151-163.

REZASOLTANI M, LU Kun, SCHOBEIRI M T, et al. A combined experimental and numerical study of the turbine blade tip film cooling effectiveness under rotation condition [J]. Journal of Turbomachinery, 2015, 137(5): 051009.

ZHOU Zhihua, WANG Songtao, CHEN Shaowen. Numerical study of blade tip cooling at high speed with tip and pressure-side coolant injections [C]∥ASME Turbo Expo 2018: Turbomachinery Technical Conference and Exposition. New York, USA: ASME, 2018: V05AT12A012.

HALILA E E, LENAHAN D T, THOMAS T T. Energy efficient engine high pressure turbine test hardware detailed design report [EB/OL].(1982-06-01)[2021-08-05]. https: ∥ntrs.nasa.gov/citations/1985 0002687.

KIM J, SEO W, BANG M, et al. Effect of shelf squealer tip configurations on film cooling effectiveness [C]∥ASME Turbo Expo 2018: Turbomachinery Technical Conference and Exposition. New York, USA: ASME, 2018: V05CT19A006.

KWAK J S, HAN J C. Heat transfer coefficients and film cooling effectiveness on the squealer tip of a gas turbine blade [J]. Journal of Turbomachinery, 2003, 125(4): 648-657.

陶文铨. 计算传热学的近代进展 [M]. 北京: 科学出版社, 2000: 362-363.

LIU Zhansheng, YANG Kefeng, YANG Xing, et al. Optimization of fan-shaped film cooling holes for enhancing cooling effectiveness under variable coolant inlet pressure ratios [C]∥ASME Turbo Expo 2020: Turbomachinery Technical Conference and Exposition. New York, USA: ASME, 2020: V07BT12A 039.

张子寒, 何坤, 晏鑫. 带造型凹坑孔的平板气膜冷却特性研究 [J]. 西安交通大学学报, 2020, 54(7): 84-93.

ZHANG Zihan, HE Kun, YAN Xin. Investigation on the film cooling efficiency on a plain surface with hole embedded in contoured crater [J]. Journal of Xi'an Jiaotong University, 2020, 54(7): 84-93.

AGA V, ABHARI R S. Influence of flow structure on compound angled film cooling effectiveness and heat transfer [J]. Journal of Turbomachinery, 2011, 133(3): 031029.

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

隔板位置对凹槽叶顶传热和冷却性能的影响

压力面侧小翼结构对凹槽叶顶冷却传热性能的影响

射流角对带小翼凹槽叶顶冷却传热性能的影响

透平级带压力侧小翼凹槽叶顶的传热与气膜冷却性能研究

气膜孔堵塞对凹槽叶顶冷却传热性能的影响