8字形盘密封螺旋泵啮合特性分析

史后威; 王增丽; 王宗明; 李彦; 冯全科

doi:10.7652/xjtuxb202109018

您当前的位置：

首页 >

文章列表页 >

8字形盘密封螺旋泵啮合特性分析

更新时间：2025-07-09

- 8字形盘密封螺旋泵啮合特性分析
- Analysis of Meshing Characteristics of 8-Shaped Disc Seal Screw Pump
- 西安交通大学学报 2021年55卷第9期页码：161-167
- 作者机构：
  
  中国石油大学(华东)新能源学院,山东,青岛,266580
- 作者简介：
- 基金信息：
  
  : 2021-02-14。作者简介: 史后威(1995—),男,硕士生;王增丽(通信作者),女,副教授,硕士生导师。基金项目: 国家重点研发计划资助项目(2020YFB2010002);国家自然科学基金资助项目(51706247);中央高校基本科研业务费专项资金资助项目(20CX02312A)
- DOI：10.7652/xjtuxb202109018
  中图分类号： TN23
- 网络首发：2021-09-10，
  
  纸质出版：2021
- 稿件说明：
移动端阅览
史后威, 王增丽, 王宗明, 等. 8字形盘密封螺旋泵啮合特性分析[J]. 西安交通大学学报, 2021,55(9):161-167.

Analysis of Meshing Characteristics of 8-Shaped Disc Seal Screw Pump[J]. 2021, 55(9): 161-167.
史后威, 王增丽, 王宗明, 等. 8字形盘密封螺旋泵啮合特性分析[J]. 西安交通大学学报, 2021,55(9):161-167. DOI： 10.7652/xjtuxb202109018.

Analysis of Meshing Characteristics of 8-Shaped Disc Seal Screw Pump[J]. 2021, 55(9): 161-167. DOI： 10.7652/xjtuxb202109018.

摘要

针对传统的圆盘密封单螺杆泵排量小、振动大、不能实现完全的自驱动等问题

创新性地提出了一种新型的8字形盘密封螺旋泵; 基于空间啮合原理建立了8字形密封盘-螺杆转子啮合副的型面方程

研究了8字形盘任意圆心角位置处的啮合特性

并分析了啮合副的结构参数对啮合特性的影响。研究结果表明:在8字形盘转动过程中

不同圆心角截面处啮合角的上下浮动范围不同

圆心角β越接近0

啮合点的波动程度越剧烈; 当圆心角β∈(0

π/2)时

啮合部位主要集中于中性面下方

当圆心角β∈(-π/2

0)时

啮合部位主要集中于中性面上方; 8字形盘大圆半径对啮合角变化程度的影响最大

中心距及8字形盘边缘倒角半径的影响较小。上述研究结果对8字形盘密封螺旋泵的进一步研发设计具有一定的指导意义。

Abstract

Aiming at the problems that the displacement is small and the self-driving is difficult to realize for traditional disc-seal single screw pump(DSSP)

this paper proposes a new type of 8-shaped disc seal screw pump

and the profile equation of the screw rotor-disc seal is established based on the spatial meshing theory. The profile equation is used to study the meshing characteristics of the 8-shaped disc seal

and the influence of structural parameters of the meshing pairs on meshing characteristics is analyzed. The results indicate that the fluctuation degree of the meshing angle is different at different central angle sections. The fluctuation degree of the meshing angle is the most severe when the central angle β is close to 0. The meshing parts are mainly concentrated below the neutral surface when β∈(0

π/2)

and above the neutral surface when β∈(-π/2

0). The radius of the big circle of the 8-shaped disc seal has the greatest influence on the variation degree of the meshing angle

while the center distance and the chamfering radius of the 8-shaped disc seal have little influence. This research may have certain guiding significance for the design and further development of 8-shaped disc seal screw pump.

关键词

Keywords

references

牛克胜. 单螺杆泵在污水处理厂的应用 [J]. 水泵技术, 2004(1): 44-46.

江威. 采油螺杆泵经济效益分析 [J]. 通用机械, 2011(2): 50-52.

JIANG Wei. Economic benefit analysis of oil well screw pump [J]. General Machinery, 2011(2): 50-52.

魏纪德. 螺杆泵工作特性研究及应用 [D]. 大庆: 大庆石油学院, 2007.

MILLS R A R. Progressing cavity oil well pumps: past, present and future [J]. Journal of Canadian Petroleum Technology, 1994, 33(4): 5-6.

杜秀华. 采油螺杆泵螺杆套副力学特性及磨损失效研究 [D]. 大庆: 大庆石油学院, 2010.

林顺德. 单螺杆泵的力学分析与磨损研究 [D]. 西安: 西安石油大学, 2014.

史建强, 房景奎, 郭颖. 采油螺杆泵磨损机理试验性研究 [J]. 科学技术与工程, 2012, 12(5): 1151-1154.

SHI Jianqiang, FANG Jingkui, GUO Ying, et al. Test research on oil screw pumps wear mechanism [J]. Science Technology and Engineering, 2012, 12(5): 1151-1154.

王哲, 王世杰, 吕晓仁. 潜油螺杆泵定子橡胶摩擦磨损行为研究 [J]. 机械设计与制造, 2014(2): 163-166.

WANG Zhe, WANG Shijie, LÜ Xiaoren. Research of friction and wear for stator rubber of oil extraction progressing cavity pump [J]. Machinery Design Manufacture, 2014(2): 163-166.

LIN B C, WANG J, HUANG Q X, et al. Effects of potassium hydroxide on the catalytic pyrolysis of oily sludge for high-quality oil product [J]. Fuel, 2017, 200: 124-133.

JUBLEE J, SUPARNA M. Characterization of oily sludge from a refinery and biodegradability assessment using various hydrocarbon degrading strains and reconstituted consortia [J]. Journal of Environmental Management, 2015, 149: 118-125.

王玉珍, 王树众, 李艳辉, 等. 超临界CO2萃取油泥砂中柴油的可行性及经济性分析 [J]. 西安交通大学学报, 2015, 49(5): 128-133.

WANG Yuzhen, WANG Shuzhong, LI Yanhui, et al. Feasibility and economic analysis of diesel oil extraction from oiled-sand by supercritical CO2 process [J]. Journal of Xi'an Jiaotong University, 2015, 49(5): 128-133.

马洁, 李博. 关于污油泥处理技术的研究 [J]. 化工管理, 2018(18): 174.

JOHANSSON A. Screw pump: WO 91/14869 [P]. 1991-10-03.

申迎峰. 圆盘密封单螺杆泵啮合特性及工作机理研究 [D]. 青岛: 中国石油大学(华东), 2018.

王增丽, 申迎峰, 王宗明, 等. 圆盘密封单螺杆泵啮合特性研究 [J]. 西安交通大学学报, 2018, 52(5): 69-74.

WANG Zengli, SHEN Yingfeng, WANG Zongming, et al. Research on the meshing characteristics of disc-seal single screw pump [J]. Journal of Xi'an Jiaotong University, 2018, 52(5): 69-74.

WANG Zengli, WANG Hao, WANG Zongming, et al. Study on the suction capacity of disc-seal single screw pump used in energy recovery systems [J]. International Journal of Refrigeration, 2020, 112: 333-340.

WANG Zengli, SHI Houwei, WANG Shuyu, et al. Study on the operating characteristic of disc seal single screw pump used in energy recovery systems [J]. International Journal of Refrigeration, 2020, 118: 336-344.

吴伟烽, 冯全科, 徐健. 单螺杆压缩机齿型的多圆柱包络原理 [J]. 西安交通大学学报, 2007, 41(11): 1271-1274.

WU Weifeng, FENG Quanke, XU Jian. Principle of multi-column envelope couple of single screw compressor [J]. Journal of Xi'an Jiaotong University, 2007, 41(11): 1271-1274.

李增亮, 石白妮, 鲁佳琪, 等. 全金属单螺杆泵结构优化设计 [J]. 石油机械, 2013, 41(12): 97-101.

LI Zengliang, SHI Baini, LU Jiaqi, et al. Optimum design of all-metal screw pump [J]. China Petroleum Machinery, 2013, 41(12): 97-101.

赵斌, 王可. 单螺杆压缩机啮合副啮合特性的主要影响因素研究 [J]. 压缩机技术, 2013(4): 40-42.

ZHAO Bin, WANG Ke. Study on main affecting factors of meshing property of meshing pair for single screw compressor [J]. Compressor Technology, 2013(4): 40-42.

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

圆盘密封单螺杆泵啮合特性研究

人形机器人关节用新型行星滚柱丝杠副加工误差作用机理

平行轴渐开线变厚齿轮传动的几何设计与啮合特性分析

电子级超纯氮深冷空分流程节能优化研究

混合电解槽阵列协同的风光耦合制氢系统双层多目标优化