双金属复合管直角法兰双辊夹持旋压起皱分析

范淑琴; 王琪; 华毅; 赵升吨; 赵永强

doi:10.7652/xjtuxb201809002

您当前的位置：

首页 >

文章列表页 >

双金属复合管直角法兰双辊夹持旋压起皱分析

更新时间：2025-05-01

- 双金属复合管直角法兰双辊夹持旋压起皱分析
- Analysis on Wrinkling in Double-Roller Clamping Spinning of Right-Angle Flange of Bimetal Composite Tube
- 西安交通大学学报 2018年52卷第9期页码：10-18
- 作者机构：
  
  西安交通大学机械工程学院,西安,710049
- 作者简介：
- 基金信息：
  
  : 2018-03-21。作者简介: 范淑琴(1977—),女,讲师。基金项目: 国家自然科学基金重点资助项目(51335009);陕西省科技统筹创新工程计划资助项目(2011KTCQ01-04)
- DOI：10.7652/xjtuxb201809002
  中图分类号： TG306
- 网络首发：2018-09-10，
  
  纸质出版：2018
- 稿件说明：
移动端阅览
范淑琴, 王琪, 华毅, 等. 双金属复合管直角法兰双辊夹持旋压起皱分析[J]. 西安交通大学学报, 2018,52(9):10-18.

FAN Shuqin, WANG Qi, HUA Yi, et al. Analysis on Wrinkling in Double-Roller Clamping Spinning of Right-Angle Flange of Bimetal Composite Tube[J]. 2018, 52(9): 10-18.
范淑琴, 王琪, 华毅, 等. 双金属复合管直角法兰双辊夹持旋压起皱分析[J]. 西安交通大学学报, 2018,52(9):10-18. DOI： 10.7652/xjtuxb201809002.

FAN Shuqin, WANG Qi, HUA Yi, et al. Analysis on Wrinkling in Double-Roller Clamping Spinning of Right-Angle Flange of Bimetal Composite Tube[J]. 2018, 52(9): 10-18. DOI： 10.7652/xjtuxb201809002.

摘要

为了将双辊夹持旋压成形技术应用于双金属复合管直角法兰成形

对Q235普通钢/304不锈钢双金属复合管管端的直角法兰双辊夹持旋压成形机理进行了研究。采用有限元分析软件建立了内层为304不锈钢、外层为Q235普通钢的双金属复合管的双辊夹持旋压成形有限元模型

通过有限元仿真模拟

分析了双辊夹持旋压成形过程易产生的起皱缺陷形式及其影响因素。研究结果表明

旋辊进给率和坯料的径厚比是起皱的主要影响因素:旋辊进给率越大则所需的成形转矩越大

在一定范围内工件的成形质量也越好

但旋辊进给率过大会出现不同程度的起皱现象; 坯料径厚比越大

所需要的成形转矩就越小

而成形过程中旋辊接触部位存在切向压应力

使得在一定径厚比条件下可成形的法兰宽度存在极限值

大于极限值则会发生起皱现象。对起皱情况下的成形力进行了分析

发现可以利用旋压力曲线的突然波动来确定起皱发生的时刻。

Abstract

To apply the double-roller clamping spinning(DRCS)process to forming right-angle flange of bimetal composite tube end

the forming mechanism of DRCS process for right-angle flange of ordinary Q235 steel/304 stainless steel bimetal composite tube is investigated

and a finite element model of DRCS for the right-angle flange of bimetal composite tube end is constructed. The inner layer of the bimetal composite tube is 304 stainless steel

and the outer layer is ordinary Q235 steel. Finite element simulation is conducted to analyze both the wrinkling form and its influence factors in the DRCS process of right-angle flange of the ordinary Q235 steel/304 stainless steel bimetal composite tube. The results show that the roller feed rate and the diameter-to-thickness ratio are the key factors influencing wrinkling in DRCS process. When the roller feed rate rises

the forming moment increases

and better forming quality of flange can be achieved within a certain range of roller feed rate. If the roller feed rate is too high

wrinkling occurs to different degrees. When the diameter-to-thickness ratio increases

the forming moment decreases. The tangential compressive stress exists in the roller contact area during the forming process

so the formed flange width has a limit value for a certain diameter-to-thickness ratio. If the flange width is greater than the limit value

the wrinkling occurs. The analysis of the forming forces in the wrinkling case shows that sudden fluctuation of the forming force can indicate the moment of wrinkling occurrence.

关键词

Keywords

references

孙育禄, 白真权, 张国超, 等. 油气田防腐用双金属复合管研究现状 [J]. 全面腐蚀控制, 2011, 25(5): 10-12, 16.SUN Yulu, BAI Zhenquan, ZHANG Guochao, et al. Research status on anticorrosion properties of bimetallic composite tubes in oil and gas field [J]. Total Corrosion Control, 2011, 25(5): 10-12, 16

GS-Hydro Group. GS-90° flare flange system [EB/OL]. [2017-06-10]. http: ∥www.gshydro.com/gs-hydro-produc ts

刘建敏. 非焊接管连接扩口法兰旋压机设计 [D]. 天津: 天津大学, 2007: 1-9

范淑琴, 赵升吨, 张琦, 等. 直角法兰双辊夹持扩径旋压有限元模型确定 [J]. 西安交通大学学报, 2010, 44(5): 66-70.FAN Shuqin, ZHAO Shengdun, ZHANG Qi, et al. Finite element model determination of double rollers clamping expanding spinning for right-angle flange [J]. Journal of Xi'an Jiaotong University, 2010, 44(5): 66-70

范淑琴, 赵升吨, 张琦, 等. 双辊夹持板料旋压成形过程塑性变形行为的研究 [J]. 精密成形工程, 2010, 2(1): 1-4.FAN Shuqin, ZHAO Shengdun, ZHANG Qi, et al. Research on plastic deformation behavior of double rollers clamping sheet metal spinning process [J]. Journal of Netshape Forming Engineering, 2010, 2(1): 1-4

FAN Shuqin, ZHAO Shengdun, ZHANG Qi, et al. Finite-element modeling of a novel flanging process on a cylinder with a large diameter-thickness ratio [J]. Proceedings of the Institution of Mechanical Engineers: Part B Journal of Engineering Manufacture, 2011, 225(7): 1117-1127

范淑琴, 赵升吨, 张琦. 旋辊参数对双辊夹持旋压成形的影响规律 [J]. 机械工程学报, 2012, 48(18): 60-66.FAN Shuqin, ZHAO Shengdun, ZHANG Qi. Research on effects of roller parameters on double rollers clamping spinning [J]. Journal of Mechanical Engineering, 2012, 48(18): 60-66

FAN Shuqin, ZHAO Shengdun, ZHANG Qi, et al. Plastic mechanism of multi-pass double-roller clamping spinning for arc-shaped surface flange [J]. Chinese Journal of Mechanical Engineering, 2013, 26(6): 1127 -1137

王成和, 刘克璋, 周路. 旋压技术 [M]. 福州: 福建科学技术出版社, 2017: 9-36

赵云豪, 李彦利. 旋压技术与应用 [M]. 北京: 机械工业出版社, 2008: 1-12

WONG C C, DEAN T A, LIN J. A review of spinning, shear forming and flow forming processes [J]. International Journal of Machine Tools and Manufacture, 2003, 43(14): 1419-1435

MUSIC O, ALLWOOD J M, KAWAI K. A review of the mechanics of metal spinning [J]. Journal of Materials Processing Technology, 2010, 210(1): 3-23

夏琴香, 熊盛勇, 潘兴毅, 等. 不锈钢/铝/不锈钢复合板拉深工艺及有限元数值模拟 [J]. 精密成形工程, 2016, 8(2): 37-42.XIA Qinxiang, XIONG Shengyong, PAN Xingyi, et al. Deep-drawing process and finite element numerical simulation for stainless steel/aluminum/stainless steel composite sheet [J]. Journal of Netshape Forming Engineering, 2016, 8(2): 37-42

WANG L, LONG H, ASHLEY D, et al. Effects of the roller feed ratio on wrinkling failure in conventional spinning of a cylindrical cup [J]. Proceedings of the Institution of Mechanical Engineers: Part B Journal of Engineering Manufacture, 2011, 225(1): 1991-2006

金利英,赵升吨.混合测量子空间聚类算法的研究.2018,52(3):139-144

张立军,马东辰,赵昕辉,等.小型H型垂直轴风力机变桨机构的优化设计与试验.2018,52(3):132-138

董渊哲,赵升吨,崔敏超,等.40Cr圆棒低应力剪切的激光旋切环形槽理论与试验研究.2016,50(11):121-128

赵永强,赵升吨,魏伟锋,等.螺杆转子磨削及计算机数控砂轮修整.2016,50(8):6-14

陈超,赵升吨,崔敏超,等.铆压重塑形工艺的铆钉优化与试验研究.2016,50(3):94-100

张琦,贲宁宇,王聚存,等.花键轴振动挤压成形试验研究.2015,49(11):110-115

李泳峄,赵升吨,范淑琴,等.花键轴增量式滚轧成形工艺的分流方式及温度效应研究.2012,46(9):60-65

谢嘉,赵升吨,梁锦涛,等.压力机杆系优化求解的变量循序组合响应面法.2012,46(5):57-62

尚万峰,赵升吨.伺服压力机加工工艺的Bezier模型及其优化研究.2012,46(3):31-35

张琦,陈余秋,方建儒.盒形件压铸模具冷却流道排布的研究.2011,45(7):38-44

范淑琴,赵升吨,张琦,等.直角法兰双辊夹持扩旋成形有限元模型的确定.2010,44(5):66-70

魏树国,赵升吨,张立军,等.直驱泵控式液压机液压系统的动态特性仿真及优化.2009,43(7):79-82

张立军,赵升吨,唐勇.热应力对金属棒料内部损伤的机理研究.2009,43(1):99-102

赵升吨,申亚京,尚万峰.轧机机架参数敏感性分析及顺序优化的研究.2008,42(1):1-4

尚万峰,赵升吨,申亚京,等.变容差遗传算法求解多约束问题的研究.2007,41(11):1267-1270

赵升吨,张志远,林军,等.圆筒形件拉深工艺的有效压边力研究.2007,41(9):1012-1016

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

圆筒形件拉深工艺的有效压边力研究

钛合金网板多点成形起皱缺陷的数值模拟

直角法兰双辊夹持扩旋成形有限元模型的确定

混合电解槽阵列协同的风光耦合制氢系统双层多目标优化

采用机器学习的大规模并行程序I/O性能建模与预测方法