涡发生器高度对气膜冷却性能影响的实验研究

张超; 宋英杰; 宋立明; 李军; 丰镇平

doi:10.7652/xjtuxb201703004

您当前的位置：

首页 >

文章列表页 >

涡发生器高度对气膜冷却性能影响的实验研究

更新时间：2025-07-09

- 涡发生器高度对气膜冷却性能影响的实验研究
- Experimental Investigation for Effects of Vortex Generator Height on Film Cooling Property
- 西安交通大学学报 2017年51卷第3期页码：20-26
- 作者机构：
  
  西安交通大学叶轮机械研究所,西安,710049
- 作者简介：
- 基金信息：
- DOI：10.7652/xjtuxb201703004
  中图分类号： TK474
- 网络首发：2017-03-10，
  
  纸质出版：2017
- 稿件说明：
移动端阅览
张超, 宋英杰, 宋立明, 等. 涡发生器高度对气膜冷却性能影响的实验研究[J]. 西安交通大学学报, 2017,51(3):20-26.

Experimental Investigation for Effects of Vortex Generator Height on Film Cooling Property[J]. 2017, 51(3): 20-26.
张超, 宋英杰, 宋立明, 等. 涡发生器高度对气膜冷却性能影响的实验研究[J]. 西安交通大学学报, 2017,51(3):20-26. DOI： 10.7652/xjtuxb201703004.

Experimental Investigation for Effects of Vortex Generator Height on Film Cooling Property[J]. 2017, 51(3): 20-26. DOI： 10.7652/xjtuxb201703004.

摘要

为了研究涡发生器高度对气膜冷却性能影响的规律

搭建了气膜冷却实验台

利用热电偶测温获得气膜有效度

采用粒子成像测速(PIV)技术拍摄了流场结构。实验中采用20°单孔射流结构

在主流湍流度为0.4%、吹风比M=1.5的条件下

完成了5种不同高度涡发生器的气膜冷却效果以及流场结构的测量。气膜有效度的测量结果表明

涡发生器能显著提高气膜冷却性能

其高度对气膜冷却性能的影响显著

该影响随着高度的增加先增大后减小

最优高度下平均气膜有效度相对不带涡发生器情况提高了81%。结合PIV流场结果分析可知:反肾形涡对将冷气卷向壁面是涡发生器提高气膜冷却性能的根本原因

但涡发生器高度过低时产生的反肾形涡对强度较弱

不能有效地将射流牵引至壁面; 当涡发生器高度过高时则会穿透射流

将部分主流卷入到反肾形涡对中

从而削弱冷却效果。

Abstract

A test rig is constructed to investigate the effects of vortex generator height on film cooling property. The thermocouples and the technology of Particle Image Velocimetry(PIV)are used to measure the wall temperature and visualize the flow distribution. The experiment is carried out in a single-jet structure with an inclination angle of 20 degrees. The scale of turbulence and the blowing ratio are set to be 0.4% and 1.5 respectively. The film cooling effectiveness and the flow structure in the vortex generators of five different heights are measured. It indicates that the film cooling performance can be significantly improved by the vortex generator

and the performance of the vortex generator is obviously affected by the height. With the increasing height of the vortex generator

the performance of the vortex generator is first enhanced and then deteriorated. At the optimal height

the average film cooling effectiveness of the plate equipped with vortex generator is increased by 81% compared with the case without vortex generator. Analyzing the PIV flow

the enhancement of film cooling is found owing to the formation of anti-kidney pair of vortices. However

in the shortest height model the anti-kidney vortices generated is too weak to effectively transport the jet toward the wall

while in the highest height model the vortex generator penetrates into the hot gas entrained into the strong anti-kidney vortices to decline the cooling effectiveness.

关键词

Keywords

references

HAN J, DUTTA S, EKKAD S. Gas turbine heat transfer and cooling technology [M]. Abingdon, UK: CRC Press, 2012: 159-160.

FRIC T F, ROSHKO A. Vortical structure in the wake of a transverse jet [J]. Journal of Fluid Mechanics, 1994, 279: 1-47.

GOLDSTEIN R J, ECKERT E, BURGGRAF F. Effects of hole geometry and density on three-dimensional film cooling [J]. International Journal of Heat and Mass Transfer, 1974, 17(5): 595-607.

HEIDMANN J D, EKKAD S. A novel antivortex turbine film-cooling hole concept [J]. ASME Journal of Turbomachinery, 2008, 130(3): 31020.

DHUNGEL S, PHILLIPS A, EKKAD S V, et al. Experimental investigation of a novel anti-vortex film cooling hole design: GT2007-27419 [R]. New York, USA: ASME, 2007.

NA S, SHIH T I. Increasing adiabatic film-cooling effectiveness by using an upstream ramp [J]. ASME Journal of Heat Transfer, 2007, 129(4): 464-471.

BARIGOZZI G, FRANCHINI G, PERDICHIZZI A. The effect of an upstream ramp on cylindrical and fan-shaped hole film cooling: part I Aerodynamic results [C]∥ASME Turbo Expo 2007. New York, USA: ASME, 2007: 105-113.

SAKAI E, TAKAHASHI T, AGATA Y. Experimental Study on effects of internal ribs and rear bumps on film cooling effectiveness [J]. ASME Journal of Turbomachinery, 2013, 135(3): 031025.

KFYS H K. Improvement of turbine vane film cooling performance by double flow control devices [J]. ASME Journal of Turbomachinery, 2016, 138(11): 111005.

RIGBY D L, HEIDMANN J D. Improved film cooling effectiveness by placing a vortex generator downstream of each hole [C]∥ASME Turbo Expo 2008: Power for Land, Sea, and Air. New York, USA: ASME, 2008: 1161-1174.

ZAMAN K B M Q, RIGBY D L, HEIDMANN J D. Experimental study of an inclined jet-in-cross-flow interacting with a vortex generator [C]∥48th AIAA Aerospace Sciences Meeting. Reston, VA, USA: AIAA, 2010: 4-7.

SHINN A F, VANKA S P. Large eddy simulations of film-cooling flows with a micro-ramp vortex generator [J]. ASME Journal of Turbomachinery, 2013, 135: 0110041.

宋英杰, 郭振东, 宋立明, 等. 基于代理模型的带微涡发生器强化换热结构的气膜冷却优化设计 [C]∥2015年工程热物理学会热机气动热力学学术会议论文集. 北京: 工程热物理学会, 2015: 152082.

杜长河,范小军,李亮,等.抽吸孔对旋流和冲击冷却流动传热特性的影响.2017,51(1):19-24.[doi:10.7652/xjtuxb 201701004]

范小军,李亮,李森,等.平板和静叶表面气流-水膜耦合流动特性的数值研究.2016,50(11):7-13.[doi:10.7652/xjtuxb 201611002]

范小军,杜长河,李亮,等.气膜孔几何位置对旋流冷却流动与传热特性的影响.2016,50(7):32-38.[doi:10.7652/xjtuxb201607006]

高炎,晏鑫,李军.燃气透平叶片尾缘开缝结构冷却性能的数值研究.2016,50(3):29-37.[doi:10.7652/xjtuxb201603 005]

周骏飞,王新军,张峰.连续收缩扩张气膜孔排冷却特性的数值模拟.2016,50(3):38-44.[doi:10.7652/xjtuxb201603006]

李志刚,李军,丰镇平.进口防旋板对孔型密封非定常气流激振特性的影响.2016,50(1):16-21.[doi:10.7652/xjtuxb 201601003]

周俊安,刘立军,肖萍,等.带叶片扩压器离心压缩机模型级内流研究.2015,49(9):30-35.[doi:10.7652/xjtuxb201509 006]

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

张角凹坑气膜孔对双层壁气膜冷却特性的影响

带肋曲面双层壁偏转内流与传热冷却特性数值研究

涡轮叶栅前缘区域叶片与端壁交互气膜冷却作用数值研究

面向气膜冷效提升的涡轮叶栅全端壁非轴对称造型设计优化

曲面双层壁结构的内外复合流动及综合冷却特性数值研究