单螺杆压缩机工作腔喷液过程几何特性及工作机理研究

王增丽 1; 申迎峰 1; 王振波 1; 王君 1; 冯全科 2

doi:10.7652/xjtuxb201702020

您当前的位置：

首页 >

文章列表页 >

单螺杆压缩机工作腔喷液过程几何特性及工作机理研究

更新时间：2025-07-09

- 单螺杆压缩机工作腔喷液过程几何特性及工作机理研究
- Geometric Characteristic and Working Mechanism of Injection Process in Single Screw Compressor with Injection
- 西安交通大学学报 2017年51卷第2期页码：128-134
- 作者机构：
  
  中国石油大学(华东)化学工程学院,山东,青岛,266580
- 作者简介：
- 基金信息：
  
  : 2016-07-29。作者简介: 王增丽(1987—),女,博士,讲师。基金项目: 山东省自然科学基金资助项目(ZR 2015EL032);中国博士后科学基金资助项目(2015M572094);青岛市博士后基金资助项目(2015232)
- DOI：10.7652/xjtuxb201702020
  中图分类号： TH45
- 网络首发：2017-02-10，
  
  纸质出版：2017
- 稿件说明：
移动端阅览
王增丽 1, 申迎峰 1, 王振波 1, 等. 单螺杆压缩机工作腔喷液过程几何特性及工作机理研究[J]. 西安交通大学学报, 2017,51(2):128-134.

Geometric Characteristic and Working Mechanism of Injection Process in Single Screw Compressor with Injection[J]. 2017, 51(2): 128-134.
王增丽 1, 申迎峰 1, 王振波 1, 等. 单螺杆压缩机工作腔喷液过程几何特性及工作机理研究[J]. 西安交通大学学报, 2017,51(2):128-134. DOI： 10.7652/xjtuxb201702020.

Geometric Characteristic and Working Mechanism of Injection Process in Single Screw Compressor with Injection[J]. 2017, 51(2): 128-134. DOI： 10.7652/xjtuxb201702020.

摘要

为了分析工作腔喷液单螺杆压缩机喷液过程的几何特性及喷液机理

基于单螺杆压缩机的工作特性

确定了螺槽与喷液孔连通时的特征角度

在此基础上

建立了工作腔喷液的几何模型

得到了任意星轮转角位置处的有效喷液面积

分析了不同喷液孔初始位置及喷液孔径对有效喷液面积的影响。基于工作腔喷液的几何模型提出了喷液过程理论计算方法

对单螺杆压缩机工作腔喷液的机理进行了研究

结果表明:压缩机工作过程中

喷液孔面积随星轮转角呈现先增大后减小的趋势; 喷液孔初始位置和喷液孔径两者共同影响喷液开始角度和喷液持续时间

喷液量受喷液面积和喷液孔前后压差这两个因素共同影响

且在喷液孔面积最大的起始位置存在一个最大单位角度喷液量。通过对工作腔喷液机理进行分析

可为以后单螺杆压缩机工作腔喷液过程的优化设计提供理论基础。

Abstract

To analyze the working cavity injection mechanism and geometric characteristic of the injection process in single screw compressor(SSC)

the critical angles as the injection hole connecting with the screw groove are determined according to the working properties of SSC. Analyzing the critical angles

a geometry model of working cavity injection is established

and the effective injection area at a certain rotation angle of the star-wheel is evaluated. A influences of the initial position and the diameter of the injection hole on the effective injection area are discussed with this model. A theoretical calculating model of the injection process is also presented to reveal the working cavity injection mechanism in SSC. The analysis shows that the injection area increases firstly and then decreases with the star-wheel angle. The starting injection angle and the injection duration time are commonly affected by the initial position and diameter of injection hole

and the injection amount is affected by both the injection area and pressure difference before and after injection hole. There exists a biggest injection quantity per angle at the original position of the largest injection area.

关键词

Keywords

references

UMEZU K, SUMA S. Heat pump room air-conditioner using variable capacity compressor [J]. ASHRAE Transactions, 1984, 90(1a): 335-349.

HOLTZAPPLE M T. Reducing energy costs in vapor-compression refrigeration and air conditioning using liquid recycle: part 2 Performance [J]. ASHRAE Transactions, 1989, 95(1): 179-205.

HIRANO T, HAGINOTO K, MATSUDA S. Study on scroll compressor behavior in case of liquid refrigerant injection [J]. Transactions of Japanese Association of Refrigeration, 1993, 10: 227-238.

李强, 李涛, 郝亮, 等. 喷液在制冷系统中的应用 [J]. 制冷与空调, 2005, 5(3): 31-34.

LI Qiang, LI Tao, HAO Liang, et al. Application of the liquid injection in refrigeration system [J]. Refrigeration and Air-Conditioning, 2005, 5(3): 31-34.

AFJEI T H, SUTER P, FAVRAT D. Experimental analysis of an inverter-driven scroll compressor with liquid injection [C]∥Proceedings of International Compressor Engineering Conference at Purdue. West Lafayette, Indiana, USA: Purdue University, 1992: 541-550.

AYUB S, BUSH W J, HALLER K D. Liquid refrigerant injection in scroll compressors operating at high compression ratios [C]∥Proceedings of International Compressor Engineering Conference at Purdue. West Lafayette, Indiana, USA: Purdue University, 1992: 561-567.

DUTTA A K, YANAGISAWA T, FUKUTA M. A study on compression characteristics of wet vapor refrigerant [C]∥Proceedings of International Compressor Engineering Conference at Purdue. West Lafayette, Indiana, USA: Purdue University, 1996: 235-240.

WINANDY E L, LEBRUN J. Scroll compressors using gas and liquid injection: experimental analysis and modeling [J]. International Journal of Refrigeration, 2002, 25: 1143-1156.

HUNDY G. The development of the single screw compressor and oil reduced operation [C]∥Proceedings of International Compressor Engineering Conference at Purdue. West Lafayette, Indiana, USA: Purdue University, 1982: 222-228.

BLAISE J, DUTTO T. Influence of oil injection and pressure ratio on single screw performances at high temperatures [C]∥Proceedings of International Compressor Engineering Conference at Purdue. West Lafayette, Indiana, USA: Purdue University, 1988: 338-345.

周瑞秋, 朱雪忠. 螺杆式压缩机喷油参数对气体温度影响的计算机模拟 [J]. 流体工程, 1987(11): 13-17.

ZHOU Ruiqiu, ZHU Xuezhong. Computer simulation of the effects of oil injection parameters on gas temperature in screw compressor [J]. Fluid Engineering, 1987(11): 13-17.

DE PAEPE M, BOGAERT W, MERTENS D. Cooling of oil injected screw compressors by oil atomization [J]. Applied Thermal Engineering, 2005, 25(17/18): 2764-2779.

李红旗, 冯俊鸿, 金光熹. 润滑油雾化及其对单螺杆压缩机排气温度影响的研究 [J]. 流体工程, 1992(8): 14-16.

LI Hongqi, FENG Junhong, JIN Guangxi. Research on the effects of lubricating oil atomization on the sin-gle screw compressor exhaust temperature [J]. Fluid Engineering, 1992(8): 14-16.

周雷, 金光熹. 喷液单螺杆压缩机内液滴运动规律及其对传热的影响 [J]. 流体机械, 1998(6): 3-7.

ZHOU Lei, JIN Guangxi. The law of the droplet motion and its influence on heat transfer of the single screw compressor with liquid injection [J]. Fluid Machinery, 1998(6): 3-7.

林强, 樊灵, 金光喜. 单螺杆压缩机喷油雾化的理论分析和实验研究 [J]. 西安石油学院学报(自然科学版), 2000, 15(2): 41-44.

LIN Qiang, FAN Ling, JIN Guangxi. Theoretical analysis and experimental study of oil atomizing in a single screw compressor [J]. Journal of Xi'an Petroleum Institute(Nature Science Edition), 2000, 15(2): 41-44.

吴修闻, 李军, 陈焕新, 等. 螺杆压缩机喷油参数的理论分析与仿真研究 [J]. 压缩机技术, 2011(2): 1-4.

WU Xiuwen, LI Jun, CHEN Huanxin, et al. Theoretical analysis and simulation research on oil injection parameters of screw compressor [J]. Compressor Technology, 2011(2): 1-4.

吴伟烽. 单螺杆压缩机啮合副的多圆柱包络啮合理论及加工技术的研究 [D]. 西安: 西安交通大学, 2010: 75-77.

焦玉龙,殷翔,王驿凯,等.多领域统一建模仿真下压缩机测试系统的PI参数整定.2016,50(8):137-142.[doi:10.7652/xjtuxb201608022]

宋明毅,吴伟烽,李直.汽车空调压缩机气阀运动规律模拟.2015,49(12):144-150.[doi:10.7652/xjtuxb201512023]

孙晔晨,田玉宝,席光,等.三元叶片型面造型对离心压缩机叶轮气动性能影响的数值研究.2015,49(11):135-141.[doi:10.7652/xjtuxb201511022]

周俊安,刘立军,肖萍,等.带叶片扩压器离心压缩机模型级内流研究.2015,49(9):30-35.[doi:10.7652/xjtuxb201509 006]

吴华根,唐昊,王养浩,等.间隙对双螺杆制冷压缩机性能的影响.2015,49(2):130-134.[doi:10.7652/xjtuxb201502022]

王增丽,刘飞龙,程军明,等.单螺杆制冷压缩机单滑阀能量调节机构的几何特性分析.2014,48(7):117-123.[doi:10.7652/xjtuxb201407020]

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

多工况下离心压气机叶轮-机匣一体联合设计优化

扇贝仿生密封腔室内超临界二氧化碳泄漏流湍动能耗散机理研究

水蒸气掺混对氨裂解气旋流燃烧与排放特性的影响研究

采用机器学习的大规模并行程序I/O性能建模与预测方法

语义区分和子图整合驱动的知识图谱表示学习方法