抽吸孔对旋流和冲击冷却流动传热特性的影响

杜长河; 范小军; 李亮; 丰镇平

doi:10.7652/xjtuxb201701004

您当前的位置：

首页 >

文章列表页 >

抽吸孔对旋流和冲击冷却流动传热特性的影响

更新时间：2025-07-09

- 抽吸孔对旋流和冲击冷却流动传热特性的影响
- Comparative Analysis for Bleed Hole Influences on Flow and Heat Transfer Behavior of Vortex and Impingement Cooling
- 西安交通大学学报 2017年51卷第1期页码：19-24
- 作者机构：
  
  西安交通大学叶轮机械研究所,西安,710049
- 作者简介：
- 基金信息：
- DOI：10.7652/xjtuxb201701004
  中图分类号： TK474.7
- 网络首发：2017-01-10，
  
  纸质出版：2017
- 稿件说明：
移动端阅览
杜长河, 范小军, 李亮, 等. 抽吸孔对旋流和冲击冷却流动传热特性的影响[J]. 西安交通大学学报, 2017,51(1):19-24.

Comparative Analysis for Bleed Hole Influences on Flow and Heat Transfer Behavior of Vortex and Impingement Cooling[J]. 2017, 51(1): 19-24.
杜长河, 范小军, 李亮, 等. 抽吸孔对旋流和冲击冷却流动传热特性的影响[J]. 西安交通大学学报, 2017,51(1):19-24. DOI： 10.7652/xjtuxb201701004.

Comparative Analysis for Bleed Hole Influences on Flow and Heat Transfer Behavior of Vortex and Impingement Cooling[J]. 2017, 51(1): 19-24. DOI： 10.7652/xjtuxb201701004.

摘要

针对旋流和冲击冷却流动的不同传热特性

建立了简单旋流、复合旋流、简单冲击和复合冲击冷却模型

并在相同涡轮叶片前缘几何腔体和气动条件下进行了数值研究

得到了4种模型下的流线结构以及压力和传热系数分布。研究结果表明:旋流和冲击冷却流动存在明显差别; 旋流冷却冷气通过喷嘴沿切向高速射入腔体

形成旋转流动

壁面处冷气压力高

靠近腔体中心线处压力低; 冲击冷却冷气通过冲击孔高速垂直射入腔体并冲击在靶面上

在靶面撞击点附近形成压力尖峰区域。显然

旋流和冲击冷却的传热特性存在差异。旋流冷却冷气强烈冲刷腔体壁面

减薄热边界层厚度

形成带状高传热区域; 冲击冷却冷气强烈撞击靶面

破坏撞击点附近热边界层

形成圆形的高传热区域。旋流冷却传热分布更均匀

抗横流冲击作用更强。对于旋流冷却

抽吸孔强烈扰动冷气的旋转流动

使带状高传热区域扩大

平均传热强度增大4.5%; 对于冲击冷却

抽吸孔对冷气流动结构影响较小

传热强度提升不显著。

Abstract

The simple vortex

composite vortex

simple impingement and composite impingement cooling models are established to investigate the flow and heat transfer behavior difference between vortex cooling and impingement cooling. The numerical method is carried out with the same geometrical chamber of turbine blade leading edge and under the same aerodynamic conditions to obtain the streamline structure

pressure and heat transfer intensity distributions for different models. The results show that vortex cooling obviously differs from impingement cooling in flow pattern. Vortex cooling air jets circumferentially through jet nozzles into the chamber and generates rotational flow. Hence high pressure region appears near the wall and low pressure region appears near the chamber centerline. Impingement cooling air injects through impingement holes into the chamber and impacts on the target to lead a pressure peak region near the impact point. Vortex cooling also significantly differs from impingement cooling in heat transfer. Vortex cooling air intensely scours the chamber wall

and reduces the thermal boundary layer to form a banding high heat transfer region. Impingement cooling air intensely impacts the target

destroys the thermal boundary layer to form a circular high heat transfer region. Vortex cooling makes heat transfer more uniform and resistivity stronger to restrain cross flow. For vortex cooling

bleed holes can disturb air vortex flow intensely and expand the banding high heat transfer region

leading to 4.5% heat transfer enhancement. For impingement cooling

bleed holes exert a slight effect on flow field and heat transfer intensity.

关键词

Keywords

references

KREITH F, MARGOLIS D. Heat transfer and friction in turbulent vortex flow [J]. Applied Scientific Research: Section A, 1959, 8(1): 457-473.

HAY N, WEST P D. Heat transfer in free swirling flow in a pipe [J]. Journal of Heat Transfer, 1975, 97(3): 411-416.

GLEZER B, MOON H K, O'CONNELL T. A novel technique for the internal blade cooling [C]∥Proceedings of ASME Turbo Expo 1996. New York, USA: ASME, 1996: V004T09A015.

LING J P C W, IRELAND P T, HARVEY N W. Measurement of heat transfer coefficient distributions and flow field in a model of a turbine blade cooling passage with tangential injection [C]∥Proceedings of ASME Turbo Expo 2006. New York, USA: ASME, 2006: 325-340.

KUSTERER K, LIN G, BOHN D, et al. Heat transfer enhancement for gas turbine internal cooling by application of double swirl cooling chambers [C]∥Proceedings of ASME Turbo Expo 2013. New York, USA: ASME, 2013: V03AT12A027.

DU Changhe, LI Liang, LI Sen, et al. Effects of aerodynamic parameters on steam vortex cooling behavior for gas turbine blade leading edge [J]. Proceedings of the Institution of Mechanical Engineers: Part A Journal of Power and Energy, 2016, 230(4): 354-365.

DU Change, LI Liang, WU Xin, et al. Effect of jet nozzle geometry on flow and heat transfer performance of vortex cooling for gas turbine blade leading edge [J]. Applied Thermal Engineering, 2016, 93: 1020-1032.

杜长河, 范小军, 李亮, 等. 喷射角度和喷嘴数对旋流冷却流动与传热特性的影响 [J]. 西安交通大学学报, 2016, 50(4): 76-80.

DU Changhe, FAN Xiaojun, LI Liang, et al. Influences of jet angle and jet nozzle number on flow and heat transfer characteristics of swirl cooling [J]. Journal of Xi'an Jiaotong University, 2016, 50(4): 76-80.

LIU Z, LI J, FENG Z. Numerical study on the effect of jet slot height on flow and heat transfer of swirl cooling in leading edge model for gas turbine blade [C]∥Proceedings of ASME Turbo Expo 2011. New York, USA: ASME, 2011: 1495-1504.

刘高文, 薛彪, 彭力, 等. 叶片前缘旋流和常规冲击对比数值研究 [J]. 推进技术, 2011, 32(4): 576-580.

LIU Gaowen, XUE Biao, PENG Li, et al. Numerical investigation on difference between blade leading edge vortex and normal impingement cooling [J]. Journal of Propulsion and Technology, 2011, 32(4): 576-580.

范小军, 杜长河, 李亮. 气膜孔几何位置对旋流冷却流动与传热特性的影响 [J]. 西安交通大学学报, 2016, 50(7): 32-38.

FAN Xiaojun, DU Changhe, LI Liang. Effect of bleed hole location on vortex cooling flow and heat transfer performance [J]. Journal of Xi'an Jiaotong University, 2016, 50(7): 32-38.

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

旋转半径和叶片安装角对动叶旋流冷却流动和传热特性的影响

4种冷却结构对叶片前缘流动换热影响的比较研究

带肋曲面双层壁偏转内流与传热冷却特性数值研究

曲面双层壁结构的内外复合流动及综合冷却特性数值研究

带肋曲面双层壁偏转内流与传热冷却特性数值研究