40Cr圆棒低应力剪切的激光旋切环形槽理论与试验研究

董渊哲; 赵升吨; 崔敏超; 霍权; 任芋见

doi:10.7652/xjtuxb201611019

您当前的位置：

首页 >

文章列表页 >

40Cr圆棒低应力剪切的激光旋切环形槽理论与试验研究

更新时间：2025-07-09

- 40Cr圆棒低应力剪切的激光旋切环形槽理论与试验研究
- Theoretical and Experimental Study on Laser Rotary Grooving for 40Cr Bar Low-Stress Shearing
- 西安交通大学学报 2016年50卷第11期页码：121-128
- 作者机构：
  
  西安交通大学机械工程学院,西安,710049
- 作者简介：
- 基金信息：
  
  : 2016-03-29。作者简介: 董渊哲(1989—),男,博士生;赵升吨(通信作者),男,教授,博士生导师。基金项目: 国家自然科学基金重点资助项目(51335009);国家04科技重大专项资助项目(2009ZX04005-031);陕西省科技统筹创新工程计划资助项目(2011KTCQ01-04)
- DOI：10.7652/xjtuxb201611019
  中图分类号： TG485
- 网络首发：2016-11-10，
  
  纸质出版：2016
- 稿件说明：
移动端阅览
董渊哲, 赵升吨, 崔敏超, 等. 40Cr圆棒低应力剪切的激光旋切环形槽理论与试验研究[J]. 西安交通大学学报, 2016,50(11):121-128.

Theoretical and Experimental Study on Laser Rotary Grooving for 40Cr Bar Low-Stress Shearing[J]. 2016, 50(11): 121-128.
董渊哲, 赵升吨, 崔敏超, 等. 40Cr圆棒低应力剪切的激光旋切环形槽理论与试验研究[J]. 西安交通大学学报, 2016,50(11):121-128. DOI： 10.7652/xjtuxb201611019.

Theoretical and Experimental Study on Laser Rotary Grooving for 40Cr Bar Low-Stress Shearing[J]. 2016, 50(11): 121-128. DOI： 10.7652/xjtuxb201611019.

摘要

针对传统剪切工艺存在的断面质量差、精度低等问题

提出了一种用于金属圆棒低应力剪切的激光旋切环形槽方法

并以40Cr圆棒为例

建立了40Cr圆棒激光旋切环形槽的数学模型; 利用L

)正交试验对激光器参数(峰值功率P

、脉宽τ、脉冲频率f)和加工参数(加工转速n、离焦量s、重复圈数N)等影响因素进行了研究

通过方差及槽型分析得到了各影响因素的主次关系及最优工艺参数范围

并对采用最优工艺参数旋切环形槽的40Cr棒料进行了剪切试验。研究结果表明:影响40Cr圆棒激光旋切环形槽深度h的各因素的主次顺序为N、s、P

、f、τ、n

其中N和s的F值分别为11.925和5.268

大于F的临界值4.11

具有显著影响; 最优工艺参数范围为峰值功率P

≥9.6 kW

脉宽τ≥0.3 ms

重复圈数3≤N≤10

加工转速10 r/min≤n≤25 r/min

离焦量s=0 mm; 40Cr圆棒激光旋切环形槽的理论深度和试验深度的误差平方和为0.112 mm

表明理论槽深的计算公式误差小、准确度高; 应用该技术的40Cr圆棒剪切断面平整

断面倾斜度仅为0.3°

比传统剪切工艺的精度提高了12倍以上

剪切质量公差仅为0.35%

比传统剪切工艺的精度提高了6倍以上。

Abstract

A laser rotary grooving method on metal bar for low-stress shearing was developed to improve the precision of billets. A mathematical model was established through theoretical analysis on the laser rotary grooving process of 40Cr bars

and then L

)orthogonal tests were conducted to study the influence of factors including the laser parameters such as peak power(P

)

pulse width(τ)and pulse frequency(f)

and the processing parameters such as processing speed(n)

defoc

using amount(s)and repeat turns(N). The influence order and optimum range of these factors were obtained by means of ANOVA analysis

and further shearing experiment was carried out on 40Cr bars. The results indicate that the influence order of the factors is N>s>P

>f>τ>n

and the F values of N and s are 11.925 and 5.268 respectively

both of which have remarkable effects. The optimum ranges of these influencing factors are: P

≥9.6 kW

τ≥0.3 ms

3≤N≤10

10 r/min≤n≤25 r/min

and s=0 mm. The sum of squares of errors(ε)between theoretical depth and real depth is 0.112 mm

which proves that the calculation formula of theoretical groove depth h is accurate. Compared with the 40Cr billets processed by traditional shearing

the sheared surface inclination is 0.3°

and the weight tolerance is only 0.35%

resulting in an accuracy improvement of more than 13 times and 8 times

respectively.

关键词

Keywords

references

马广英, 郎福元, 龚俊. 裂纹技术在应力下料中的研究与应用 [J]. 甘肃科学学报, 2003, 15(3): 86-90.

MA Guangying, LANG Fuyuan, GONG Jun. Research and application of crack technology in stress blanking [J]. Journal of Gansu Sciences, 2003, 15(3): 86-90.

李有堂. 裂纹技术理论与应用 [M]. 兰州: 甘肃科学技术出版社, 2007: 22-23.

ZHAO Renfeng, ZHAO Shengdun, ZHONG Bin. Experimental study on novel precision cropping machinery using rotary striking action [J]. Applied Mechanics and Materials, 2013, 281(1): 287-292.

付建华, 李永堂, 雷步芳, 等. 金属棒料高速精密剪切试验研究 [J]. 机械工程学报, 2005, 41(5): 154-156.

FU Jianhua, LI Yongtang, LEI Bufang, et al. Experiment research on the high-speed precision shearing of metal bar [J]. Journal of Mechanical Engineering, 2005, 41(5): 154-156.

ZHONG Bin, ZHAO Shengdun, ZHAO Renfeng, et al. Investigation on the influences of clearance and notch-sensitivity on a new type of metal-bar non-chip fine-cropping system [J]. International Journal of Mechanical Sciences, 2013, 76(6): 144-151.

SAHIN A Z, AYAR T, YILBAS B S. First and second law analyses of laser cutting process in relation to the end product quality [J]. International Journal of Energy Research, 2008, 32(8): 689-697.

孟庆轩, 王续跃, 徐文骥, 等. 薄板激光切割气熔比数学建模及试验验证 [J]. 机械工程学报, 2011, 47(17): 172-178.

MENG Qingxuan, WANG Xuyue, XU Wenji, et al. Vaporization-melt ratio mathematical model and experiments of laser cutting sheet metal [J]. Journal of Mechanical Engineering, 2011, 47(17): 172-178.

BRUGMANN M H, THOMAS F. Comparative theoretical analysis of continuous wave laser cutting of metals at 1 and 10 μm wavelength [J]. Applied Physics: A, 2013, 116(3): 1353-1364.

KHELOUFI K, AMARA E H. Numerical investigation of the effect of some parameters on temperature field and kerf width in laser cutting process [J]. Physics Procedia, 2012, 39(7): 872-880.

BAZYLEVA I O, GALUSHKIN M G, GOLUBEV V S, et al. Thermal losses in the process of gas-assisted laser cutting of metals [J]. Proceedings of SPIE, 2002, 4644(4): 73-82.

GOLNABI H, BAHAR M. Investigation of optimum condition in oxygen gas-assisted laser cutting [J]. Optics Laser Technology, 2009, 41(4): 454-460.

丁升, 王建国, 刘峰, 等. 激光辐照转动充压圆柱壳体热力学效应 [J]. 强激光与粒子束, 2006, 18(11): 1787-1792.

DING Sheng, WANG Jianguo, LIU Feng, et al. Thermal-mechanical effects on rotating internally pressured cylindrical shell irradiated by laser beam [J]. High Power Laser and Particle Beams, 2006, 18(11): 1787-1792.

段文强, 王恪典, 董霞, 等. 激光旋切法加工高质量微小孔工艺与理论研究 [J]. 西安交通大学学报, 2015, 49(3): 95-103.

DUAN Wenqiang, WANG Kedian, DONG Xia, et al. Study on machining of high-quality micro-holes by laser trepan drilling [J]. Journal of Xi'an Jiaotong University, 2015, 49(3): 95-103.

陈聪, 高明, 顾云泽, 等. 光纤激光切割铝合金薄板工艺特性研究 [J]. 中国激光, 2014, 41(6): 73-79.

CHEN Cong, GAO Ming, GU Yunze, et al. Study on fiber laser cutting of aluminum alloy sheet [J]. Chinese Journal of Lasers, 2015, 49(3): 95-103.

杨慎华, 张志强, 窦淑清. 连杆预制裂纹槽激光加工工艺参数 [J]. 哈尔滨工业大学学报, 2009, 41(1): 126-129.

YANG Shenhua, ZHANG Zhiqiang, DOU Shuqing. Influence of starting notch processing methods on fracture splitting quality of connecting rod [J]. Journal of Harbin Institute of Technology, 2009, 41(1): 126-129.

郑祺峰. 发动机连杆裂解槽激光加工技术及自动化设备研究 [D]. 长春: 吉林大学, 2010.

韩艳凯, 陈连生, 宋进英, 等. 空冷奥氏体相变过程中的相变潜热 [J]. 河北理工大学学报(自然科学版), 2011, 33(3): 46-49.

HAN Yankai, CHEN Liansheng, SONG Jinying, et al. The transition latent heat of austenite phase transition in air-cooled conditions [J]. Journal of Hebei Polytechnic University(Natural Science Edition), 2011, 33(3): 46-49.

林继辉. 40Cr钢和60Si2Mn钢顶端淬火过程的数值模拟 [D]. 辽宁大连: 大连交通大学, 2010.

干勇, 田志凌, 董瀚, 等. 钢铁材料手册 [M]. 北京: 化学工业出版社, 2009: 264-265.

步明繁,刘志刚,张为波,等.采用F-P光学腔的外腔半导体激光器锁相稳频方法.2016,50(10):125-131.[doi:10.7652/xjtuxb201610019]

齐静雅,王昭,黄军辉,等.机床导轨滚转角测量误差分析.2016,50(9):31-35.[doi:10.7652/xjtuxb201609005]

郝维娜,令锋超,刘志刚,等.轴承滚珠面型误差激光干涉测量系统的研究.2016,50(6):83-89.[doi:10.7652/xjtuxb 201606013]

余宝,王昭,黄军辉,等.机床滚转角高精度测量中的频偏现象研究.2016,50(3):101-105.[doi:10.7652/xjtuxb201603 016]

吴继琸,朱刚贤,陆斌,等.自愈合效应对光内送粉激光变斑熔覆成形薄壁件的影响.2016,50(1):145-150.[doi:10.7652/xjtuxb201601022]

白浩,王伊卿,董霞,等.Ti6Al4V钛合金脉冲激光抛光微裂纹产生机理与尺寸特征研究.2015,49(12):117-123.[doi:10.7652/xjtuxb201512019]

王新孟,杨军,梅雪松,等.精密坐标镗床进给系统热误差分析与预测.2015,49(10):22-28.[doi:10.7652/xjtuxb201510 004]

张为波,刘志刚,周扬理,等.采用同步调谐方法的Littman型可调谐半导体激光器.2015,49(10):29-33.[doi:10.7652/xjtuxb201510005]

段文强,王恪典,董霞,等.激光旋切法加工高质量微小孔工艺与理论研究.2015,49(3):95-103.[doi:10.7652/xjtuxb 201503016]

郑卜祥,姜歌东,王文君,等.超快脉冲激光对钛合金的烧蚀特性与作用机理.2014,48(12):21-28.[doi:10.7652/xjtuxb 201412004]

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

离子液体改性燃料的电流体动力学效应研究

不同板叠材料热声热机能量转换过程数值模拟研究

结构-语义-残差协同的图像压缩框架：面向隐私保护与高保真重建

超临界二氧化碳向心透平轮背间隙内风阻损失及流动特性研究

隧道内燃料电池汽车氢气泄漏扩散特性及影响因素