连续收缩扩张气膜孔排冷却特性的数值模拟

周骏飞; 王新军; 张峰

doi:10.7652/xjtuxb201603006

您当前的位置：

首页 >

文章列表页 >

连续收缩扩张气膜孔排冷却特性的数值模拟

更新时间：2025-07-09

- 连续收缩扩张气膜孔排冷却特性的数值模拟
- Numerical Simulation for Cooling Characteristics with Continuous Arranged Converging Slot-Hole Rows
- 西安交通大学学报 2016年50卷第3期页码：38-44
- 作者机构：
  
  西安交通大学能源与动力工程学院,西安,710049
- 作者简介：
- 基金信息：
- DOI：10.7652/xjtuxb201603006
  中图分类号： TK263
- 网络首发：2016-03-10，
  
  纸质出版：2016
- 稿件说明：
移动端阅览
周骏飞, 王新军, 张峰. 连续收缩扩张气膜孔排冷却特性的数值模拟[J]. 西安交通大学学报, 2016,50(3):38-44.

Numerical Simulation for Cooling Characteristics with Continuous Arranged Converging Slot-Hole Rows[J]. 2016, 50(3): 38-44.
周骏飞, 王新军, 张峰. 连续收缩扩张气膜孔排冷却特性的数值模拟[J]. 西安交通大学学报, 2016,50(3):38-44. DOI： 10.7652/xjtuxb201603006.

Numerical Simulation for Cooling Characteristics with Continuous Arranged Converging Slot-Hole Rows[J]. 2016, 50(3): 38-44. DOI： 10.7652/xjtuxb201603006.

摘要

为研究连续收缩扩张孔的冷却特性

在C3X静叶片上分别建立了连续收缩扩张气膜孔冷却模型、圆柱气膜孔冷却模型和展向扩张气膜孔冷却模型

连续收缩扩张气膜孔每排23个、孔间距为20 mm

展向扩张孔每排19个、孔间距为24 mm

圆柱孔每排19个、孔间距为24 mm。同时

在叶片前部开设了一个U形冷却通道

尾部开设了一个直冷却通道

冷气通过这2个内部冷却通道进入气膜孔。利用ANSYS-ICEM商用软件对上述3种模型进行了结构化网格划分

采用ANSYS-CFX商用软件和SST湍流模型进行了数值计算和分析比较

结果表明:连续收缩扩张孔的气膜冷却效率高于圆柱孔和展向扩张孔

在孔口附近和高吹风比下的优势最明显; 连续收缩扩张孔使冷气射流在相邻两孔的交汇处形成了类似反肾形涡结构

该涡的强度不大

但具有良好的延续性和较大的冷气覆盖面积; 复合冷却时冷气射流脱离壁面的现象更明显

孔口附近总冷却效率低于绝热冷却效率。在连续收缩扩张孔的实际应用中选择偏大的吹风比和更小的入射角可以提高气膜冷却效率。

Abstract

Continuously arranged converging slot-holes are set on a C3X stator

which contains a U-bend channel at the front of the airfoil and a radial channel near the trailing edge inside the airfoil by solidworks. Cylindrical hole model and fan-shaped hole model are also constructed in the same way. Each model has four rows of film cooling holes. In the slot-hole case

there are 23 holes with a pitch of 20 millimeters in one film cooling hole row. In the cylindrical and fan-shaped hole case

there are 19 holes with a pitch of 24 millimeters in one film cooling hole row. Cooling air is supplied to film cooling holes through the U-bend channel and the radial channel. These three models are meshed by structured grids with ANSYS-ICEM. ANSYS-CFX and SST turbulence model is used to calculate the turbulent flow. The adiabatic cooling performance of converging slot-holes is compared with that of cylindrical holes and fan-shaped holes in different blowing ratio

the heat transfer enhancement mechanism of converging slot-holes is analyzed

and the adiabatic cooling effectiveness and the overall cooling effectiveness are compared. The Result shows that converging slot-hole has the highest adiabatic cooling effectiveness and the advantages become more obvious at the larger blow ratio. A kind of vortex which looks like anti-kidney vortex is found downstream of continuous arranged converging slot-holes. The intensity of the vortex is not very high but maintains in a long distance and increases the coverage of the coolant film on the surface of the stator. The internal cooling has a non-ignorable influence on the numerical result. As a consequence

conjugate cooling has less resistance to jet lift-off. The overall effectiveness is lower than the adiabatic effectiveness at the exit of slot-holes. In the practical application of the continuous arranged converging slot-hole rows

large blowing ratio and small injection angle are beneficial to promote the film cooling efficiency.

关键词

Keywords

references

GOLDSTEIN R J, ECKERT E R G, BURGGRAF F. Effects of hole geometry and density on three-dimensional film cooling [J]. International Journal of Heat and Mass Transfer, 1974, 17(5): 595-607.

BUNKER R S. A review of shaped hole turbine film-cooling technology [J]. ASME Journal of Heat Transfer, 2005, 127(4): 441-453.

SARGISON J E, GUO S M, OLDFIELD M L G, et al. A converging slot-hole film-cooling geometry: part 1 Low-speed flat-plate heat transfer and loss [J]. ASME Journal of Turbomachinery, 2002, 124(3): 453-460.

SARGISON J E, GUO S M, OLDFIELD M L G, et al. A converging slot-hole film-cooling geometry: part 2 Transonic nozzle guide vane heat transfer and loss [J]. ASME Journal of Turbomachinery, 2002, 124(3): 461-471.

AZZI A, JUBRAN B A. Numerical modelling of film cooling from converging slot-hole [J]. International Journal of Heat and Mass Transfer, 2007, 43(4): 381-388.

刘存良, 朱惠人, 白江涛. 收缩-扩张形气膜孔提高气膜冷却效率的机理研究 [J]. 航空动力学报, 2008, 23(4): 598-604.

LIU Cunliang, ZHU Huiren, BAI Jiangtao. Study on the physics of film-cooling effectiveness enhancement by the converging-expanding hole [J]. Journal of Aerospace Power, 2008, 23(4): 598-604.

刘存良, 朱惠人, 白江涛, 等. 基于瞬态液晶测量技术的收缩-扩张形孔气膜冷却特 [J]. 航空学报, 2009, 30(5): 812-818.

LIU Cunliang, ZHU Huiren, BAI Jiangtao, et al. Film cooling characteristics of converging-expanding hole with transient liquid crystal measurement technique [J]. Acta Aeronautica et Astronautica Sinica, 2009, 30(5): 812-818.[8] HYLTON L D, MIHELC M S, TURNER E R, et al. Analytical and experimental evaluation of the heat transfer distribution over the surfaces of turbine vanes, NASA 168015 [R]. Washington, DC, USA: NASA 1983.

DEES J E, BOGARD D G, LEDEZMA G A, et al. Experimental measurements and computational predictions for an internally cooled simulated turbine vane [J]. ASME Journal of Turbomachinery, 2012, 134(6): 061003.

DYSON T E. Experimental and computational investigation of film cooling on a large scale C3X turbine vane including conjugate effects [D]. Texas, USA: University of Texas at Austin, 2012: 76-85.

MCCLINTIC J W, KLAVETTER S R, WINKA J R, et al. The effect of internal crossflow on the adiabatic effectiveness of compound angle film cooling holes [J]. ASME Journal of Turbomachinery, 2015, 137(7): 071006.

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

张角凹坑气膜孔对双层壁气膜冷却特性的影响

带肋曲面双层壁偏转内流与传热冷却特性数值研究

涡轮叶栅前缘区域叶片与端壁交互气膜冷却作用数值研究

面向气膜冷效提升的涡轮叶栅全端壁非轴对称造型设计优化

曲面双层壁结构的内外复合流动及综合冷却特性数值研究