非均匀载荷下厚壁圆筒稳态蠕变应力的计算

王建梅; 苗克军; 徐俊良; 李璞

doi:10.7652/xjtuxb201509002

您当前的位置：

首页 >

文章列表页 >

非均匀载荷下厚壁圆筒稳态蠕变应力的计算

更新时间：2025-07-09

- 非均匀载荷下厚壁圆筒稳态蠕变应力的计算
- Steady-State Creep Stress Calculation of Thick-Walled Cylinder under Non-Uniform Load
- 西安交通大学学报 2015年49卷第9期页码：8-13+133
- 作者机构：
  
  太原科技大学教育部重型机械工程技术研究中心,太原,030024
- 作者简介：
- 基金信息：
  
  : 2015-01-14。作者简介: 王建梅(1972—),女,教授。基金项目: 国家自然科学基金资助项目(51205269);山西省自然科学基金资助项目(2012011018-2);山西省回国留学人员科研资助项目(2013-093)
- DOI：10.7652/xjtuxb201509002
  中图分类号： TH123
- 网络首发：2015-09-10，
  
  纸质出版：2015
- 稿件说明：
移动端阅览
王建梅, 苗克军, 徐俊良, 等. 非均匀载荷下厚壁圆筒稳态蠕变应力的计算[J]. 西安交通大学学报, 2015,49(9):8-13+133.

Steady-State Creep Stress Calculation of Thick-Walled Cylinder under Non-Uniform Load[J]. 2015, 49(9): 8-13+133.
王建梅, 苗克军, 徐俊良, 等. 非均匀载荷下厚壁圆筒稳态蠕变应力的计算[J]. 西安交通大学学报, 2015,49(9):8-13+133. DOI： 10.7652/xjtuxb201509002.

Steady-State Creep Stress Calculation of Thick-Walled Cylinder under Non-Uniform Load[J]. 2015, 49(9): 8-13+133. DOI： 10.7652/xjtuxb201509002.

摘要

根据多维应力下稳态蠕变的基础理论

采用应力函数法推导出一类外边界固定、内边界受非均匀载荷的厚壁圆筒稳态蠕变应力计算公式; 分析了不同外内径比K下厚壁圆筒的蠕变应力和应力分布情况

证实最大蠕变应力发生在厚壁圆筒内边界最大受力处

厚壁圆筒的最大蠕变应力随着壁厚的增加呈现出先增加后减小的规律

且当K=1.58时蠕变应力最大。应用所得计算公式

针对工程中油膜轴承衬套因承受油膜压力而发生的蠕变问题进行了蠕变应力解析求解。通过蠕变拉伸试验

得到了衬套内壁材料的诺顿稳态蠕变本构方程

并根据蠕变系数

利用有限元分析软件ANSYS计算了衬套的蠕变应力。最后

比较了上述2种方法得到的蠕变应力

表明文中给出的计算方法与有限元方法所得结果吻合

验证了该解析算法的正确性

从而可以为厚壁圆筒的结构设计和多维蠕变应力解析求解提供理论依据。

Abstract

Based on the basic theory of steady-state creep under multi-dimensional stress state

a steady-state creep stress calculation formula of thick-walled cylinder with fixed outer boundary was derived by the stress-function method under non-uniform internal pressure. The creep stress and stress distribution of several kinds of thick-walled cylinder were analyzed

which showed that the maximal creep stress occurred in the area with the largest stress on the inner boundary of the thick-walled cylinders

increased first and then decreased with the wall thickness

and the largest creep stress was produced when the ratio of outer diameter to internal diameter is 1.58. According to the formula

the steady-state creep stress of oil-film bearing bushing subject to a non-uniform oil-film pressure was analyzed

and the creep process was simulated by using the finite element software in ANSYS

where the creep parameters were obtained based on creep tensile test. Calculation results of the above two methods were analyzed

and the results obtained by the proposed method were coincident well with those by finite element method. This research may provide a theoretical guidance for the structural design of thick-walled cylinders and the analytical calculation of multi-dimensional creep stress.

关键词

Keywords

references

LIANG Yaping, WANG Huizhen, REN Xingmin. Analytical solution for spatially axisymmetric problem of thick-walled cylinder subjected to different linearly varying pressures along the axis and uniform pressures at two ends [J]. Science in China: Series G Physics, Mechanics and Astronomy, 2008, 51(1): 98-104.

ALTENBACH H, GORASH Y, NAUMENKO K. Steady-state creep of a pressurized thick cylinder in both the linear and the power law ranges [J]. Acta Mechanica, 2008, 195(1/2/3/4): 263-274.

NAUMENKO K, ALTENBACH H, GORASH Y. Creep analysis with a stress range dependent constitutive model [J]. Archive of Applied Mechanics, 2009, 79(6/7): 619-630.

BOYLE J T. The creep behavior of simple structures with a stress range-dependent constitutive model [J]. Archive of Applied Mechanics, 2012, 82(4): 495-514.

WU Qingliang, LÜ Aizhong, GAO Yongtao, et al. Stress analytical solution for plane problem of a double-layered thick-walled cylinder subjected to a type of non-uniform distributed pressure [J]. Journal of Central South University, 2014, 21(5): 2074-2082.

吴庆良, 吕爱钟. 一类非均布荷载作用下厚壁圆筒平面问题的应力解析解 [J]. 工程力学, 2011, 28(6): 6-10, 18.

WU Qingliang, LÜ Aizhong. Stress analytical solution for plane problem of a thick-walled cylinder subjected to a type of non-uniform distributed pressures [J]. Engineering Mechanics, 2011, 28(6): 6-10, 18.

郑俊德, 张艳秋, 王文军, 等. 非均匀载荷下套管强度的计算 [J]. 石油学报, 1998, 19(1): 119-123.

ZHENG Junde, ZHANG Yanqiu, WANG Wenjun, et al. Calculation of casing strength under nonuniform loading [J]. Acta Petrolei Sinica, 1998, 19(1): 119-123.

穆霞英. 蠕变力学 [M]. 西安: 西安交通大学出版社, 1989: 60-83.

徐芝纶. 弹性力学 [M]. 北京: 高等教育出版社, 2006: 55-63.

平修二. 金属材料的高温强度理论设计 [M]. 郭廷玮, 李安定, 徐介平, 译. 北京: 科学出版社, 1983: 259-265.

机械设计手册编委会. 机械设计手册: 第5卷 [M]. 3版. 北京: 机械工业出版社, 2004: 31-33.

SIMMONS T E, CONTARINI A, GIANNI N. 油膜轴承变形和压力分析 [J]. 钢铁, 2009, 44(3): 93-96.

SIMMONS T E, CONTARINI A, GIANNI N, et al. Deflection and pressure analysis of oil film bearings [J]. Iron and Steel, 2009, 44(3): 93-96.

王建梅, 薛亚文, 马立新, 等. 蠕变对巴氏合金ZChSnSb11-6力学性能和显微组织的影响 [J]. 中国有色金属学报, 2014, 24(10): 2513-2518.

WANG Jianmei, XUE Yawen, MA Lixin, et al. Influence of creep on mechanical properties and microstructures of Babbitt alloy ZChSnSb11-6 [J]. The Chinese Journal of Nonferrous Metals, 2014, 24(10): 2513-2518.

GLADIUS L, SHAW K M. Creep constitutive model and component lifetime estimation: the case of niobium-modified 9Cr-1Mo steel weldments [J]. Journal of Materials Engineering and Performance, 2011, 20(7): 1310-1314.

中国钢铁工业协会. GB/T 2039—2012 金属材料单轴拉伸蠕变试验方法 [S]. 北京: 中国标准出版社, 2012.

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

物理气相传输（PVT)法生长碳化硅的晶体形态热应力分析

参数曲面三角网格生成的改进波前法

谱元法应用于涡声传播问题的研究

采用非匹配网格离散的快速边界元-有限元宽频声振耦合分析

输电铁塔单变双拼角钢转换节点承载力研究