多通道测力仪动态信号反向滤波补偿方法

朱明; 毛宽民

doi:10.7652/xjtuxb201502020

您当前的位置：

首页 >

文章列表页 >

多通道测力仪动态信号反向滤波补偿方法

更新时间：2025-07-09

- 多通道测力仪动态信号反向滤波补偿方法
- Multi-Channel Dynamic Force Measurement and Compensation with Inverse Filter
- 西安交通大学学报 2015年49卷第2期页码：117-123
- 作者机构：
  
  华中科技大学机械科学与工程学院,武汉,430074
- 作者简介：
- 基金信息：
  
  : 2014-06-12。作者简介: 朱明(1985—),男,博士生;毛宽民(通信作者),男,教授,博士生导师。基金项目: 国家科技支撑计划资助项目(2014BAF08B01);国家“863计划”资助项目(2012AA040703)
- DOI：10.7652/xjtuxb201502020
  中图分类号： TN713;TH113.1
- 网络首发：2015-02-10，
  
  纸质出版：2015
- 稿件说明：
移动端阅览
朱明, 毛宽民. 多通道测力仪动态信号反向滤波补偿方法[J]. 西安交通大学学报, 2015,49(2):117-123.

Multi-Channel Dynamic Force Measurement and Compensation with Inverse Filter[J]. 2015, 49(2): 117-123.
朱明, 毛宽民. 多通道测力仪动态信号反向滤波补偿方法[J]. 西安交通大学学报, 2015,49(2):117-123. DOI： 10.7652/xjtuxb201502020.

Multi-Channel Dynamic Force Measurement and Compensation with Inverse Filter[J]. 2015, 49(2): 117-123. DOI： 10.7652/xjtuxb201502020.

摘要

为了消除动态测力仪的结构动态特性对测试结果的干扰

采用反向滤波的方法对动态力测试信号进行修正。根据最小相位系统理论设计反向数字滤波器

由单输入单输出反向数字滤波器的设计原理

提出了多输入多输出反向数字滤波器的设计方法。根据测力系统激励力与测试值之间的频响函数矩阵

建立测力系统传递函数模型

并进行最小相位转化

将最小相位动态力传递函数模型反转

得到反向滤波器。实验结果表明:经过反向滤波处理的动态力测试值与实际动态力具有相同的幅值; 运用零相位滤波方法

消除了测试信号与实际动态力之间的相位差; 测试结果与动态力实际输入幅值误差小于6%。

Abstract

To eliminate the influence of structural dynamics of dynamometer on measurement accuracy of dynamic force

an inverse filter method is considered to modify dynamic signals of the measurement system. Following the theory of the minimum-phase system

an inverse filter with multi-input and multi-output is designed

and an inverse filter matrix is established to compensate the cross-interference between dynamic forces in different directions. The frequency response matrix of the excitation force and measured one is used to model the system dynamics and to transfer into a minimum-phase system. Inverting the minimum-phase transfer function matrix

the inverse filter matrix is obtained. The simulation and experiment show that the magnitude of the measured dynamic force matches well with that of the actual dynamic force. Zero-phase filtering effectively eliminates the phase delay and the relative errors are controlled within 6%.

关键词

Keywords

references

PARK S S, ALTINTAS Y. Dynamic compensation of spindle integrated force sensors with Kalman filter [J]. Journal of Dynamic Systems, Measurement and Control, 2004, 126(3): 443-452.

ALBRECHT A, PARK S S, ALTINTAS Y, et al. High frequency bandwidth cutting force measurement in milling using capacitance displacement sensors [J]. International Journal of Machine Tools and Manufacture, 2005, 45(9): 993-1008.

田红亮, 赵春华, 朱大林, 等. 整个螺栓结合部的法向连接动刚度及试验验证 [J]. 西安交通大学学报, 2012, 46(9): 31-36.

TIAN Hongliang, ZHAO Chunhua, ZHU Dalin, et al. Analysis and validation on normal connection dynamic stiffness of bolted joint interface ensemble [J]. Journal of Xi'an Jiaotong University, 2012, 46(9): 31-36.

EHMANN K F, KAPOOR S G, DEVOR R E, et al. Machining process modeling: a review [J]. Journal of Manufacturing Science and Engineering, 1997, 119(4B): 655-663.

TOTIS G, WIRTZ G, SORTINO M, et al. Development of a dynamometer for measuring individual cutting edge forces in face milling [J]. Mechanical Systems and Signal Processing, 2010, 24(6): 1844-1857.

TOTIS G, SORTINO M. Development of a modular dynamometer for triaxial cutting force measurement in turning [J]. International Journal of Machine Tools Manufacture, 2011, 51(1): 34-42.

TRANSCHEL R, STIRNIMANN J, BLATTNER M, et al. Effective dynamometer for measuring high dynamic process force signals in micro machining operations [C]∥5th CIRP Conference on High Performance Cutting. Amsterdam, Holland: Elsevier Science BV, 2012: 558-562.

TLUSTY J, JANG D Y, TARNG Y S. Measurement of the milling force over the wide approved dynamic response [C]∥15th North American Manufacturing Research Conference. Bethlehem, Pennsylvania, USA: Society of Manufacturing Engineers, 1987: 273-280.

CHUNG Y L, SPIEWAK S A. A model of high performance dynamometer [J]. Journal of Manufacturing Science and Engineering, 1994, 116(3): 279-288.

MAGNEVALL M, LUNDBLAD M, AHLIN K, et al. High frequency measurements of cutting forces in milling by inverse filtering [J]. Machining Science and Technology, 2012, 16(4): 487-500.

田红亮, 刘芙蓉, 方子帆, 等. 引入各向同性虚拟材料的固定结合部模型 [J]. 振动工程学报, 2013, 26(4): 561-573.

TIAN Hongliang, LIU Furong, FANG Zifan, et al. Immovable joint surface's model using isotropic virtual material [J]. Journal of Vibration Engineering, 2013, 26(4): 561-573.

PANDIT S M, WU S M. Time series and system analysis with applications [M]. New York: John Wiley and Sons, 1983.

陈淑珍, 杨涛. 零相移滤波器的改进及实现方法 [J]. 武汉大学学报: 理学版, 2001, 47(3): 373-376.

CHEN Shuzhen, YANG Tao. Improvement and realization of the zero-phase filter [J]. Journal of Wuhan University: Natural Science, 2001, 47(3): 373-376.

韦兆碧,杨银堂,马志瀛,等.聚磁式光学电流互感器饱和特征的记忆效应补偿研究.2013,47(6):97-102.[doi:10.7652/xjtuxb201306017]

梁新合,梁晋,郭成,等.散乱点云的补偿滤波.2011,45(11):91-94.[doi:10.7652/xjtuxb201111017]

何英杰,刘进军,王兆安,等.三电平有源电力滤波器谐波电流跟踪无差控制方法.2009,43(8):90-94.[doi:10.7652/xjtuxb200908019]

袁敞,刘进军,王晓钰,等.一种新型串联型有源电力滤波器无谐波检测控制方法.2009,43(2):86-89.[doi:10.7652/xjtuxb200902019]

王小龙,水鹏朗,孙晓云.近似完全重构交替离散傅里叶变换调制滤波器组.2008,42(8):1001-1005.[doi:10.7652/xjtuxb200808016]

任品毅,权良辉.多输入多输出系统中基于多级维纳滤波的均衡算法.2008,42(2):218-221.[doi:10.7652/xjtuxb2008 02020]

王风华,韩九强.一种Log-Gabor滤波结合特征融合的虹膜识别方法.2007,41(8):889-893.[doi:10.7652/xjtuxb2007 08003]

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

采用试验设计方法的第三代CO2气体箔轴承箔片几何参数敏感性分析

扇贝仿生密封腔室内超临界二氧化碳泄漏流湍动能耗散机理研究

不同板叠材料热声热机能量转换过程数值模拟研究

采用机器学习的大规模并行程序I/O性能建模与预测方法

超临界二氧化碳向心透平轮背间隙内风阻损失及流动特性研究