槽缝射流对静叶端壁冷却性能的影响

杜昆; 李军; 晏鑫

doi:10.7652/xjtuxb201501004

您当前的位置：

首页 >

文章列表页 >

槽缝射流对静叶端壁冷却性能的影响

更新时间：2025-07-09

- 槽缝射流对静叶端壁冷却性能的影响
- Effect of the Slot Jet Impingement on the Cooling Performance of the Vane Endwall
- 西安交通大学学报 2015年49卷第1期页码：21-26
- 作者机构：
  
  西安交通大学叶轮机械研究所,西安,710049
- 作者简介：
- 基金信息：
  
  : 2014-04-12。作者简介: 杜昆(1990—),男,博士生;李军(通信作者),男,教授,博士生导师。基金项目: 国家自然科学基金资助项目(51376144);中央高校基本科研业务费专项资金资助项目
- DOI：10.7652/xjtuxb201501004
  中图分类号： TK474.7
- 网络首发：2015-01-10，
  
  纸质出版：2015
- 稿件说明：
移动端阅览
杜昆, 李军, 晏鑫. 槽缝射流对静叶端壁冷却性能的影响[J]. 西安交通大学学报, 2015,49(1):21-26.

Effect of the Slot Jet Impingement on the Cooling Performance of the Vane Endwall[J]. 2015, 49(1): 21-26.
杜昆, 李军, 晏鑫. 槽缝射流对静叶端壁冷却性能的影响[J]. 西安交通大学学报, 2015,49(1):21-26. DOI： 10.7652/xjtuxb201501004.

Effect of the Slot Jet Impingement on the Cooling Performance of the Vane Endwall[J]. 2015, 49(1): 21-26. DOI： 10.7652/xjtuxb201501004.

摘要

采用数值求解三维RANS方程和k-ω湍流模型

研究了槽缝射流对涡轮静叶端壁冷却性能的影响; 通过对4种湍流模型数值结果与实验数据的比较

验证了标准k-ω湍流模型可以有效模拟静叶前缘端壁的冷却性能

揭示了槽缝宽度、入射段结构和端壁边界型线对静叶端壁冷却性能的影响规律。研究结果表明:在一定的槽缝射流流量下

减小槽缝宽度能够增大冷却射流的覆盖面积

提高静叶前缘气膜孔排附近区域的冷却效率; 过渡相切圆弧的槽缝入射段结构具有最佳的静叶端壁冷却效果。端壁边界型线可改变节距方向上的槽缝冷却射流的流量分配

影响下游端壁的冷却效果

当端壁相对型线幅值为0.75、相位角为30°时

槽缝射流具有最佳的静叶端壁冷却效果。

Abstract

Effect of the slot jet impingement on the cooling performance of the vane endwall was numerically investigated using three-dimensional Reynolds-averaged Navier-Stokes(RANS)equations and k-ω turbulent model. The film cooling effectiveness of the experimental vane endwall was analyzed using four turbulent models. The accuracy of the utilized k-ω turbulent model for the cooling performance of the vane endwall was demonstrated by comparison of the experimental data and numerical results with four used turbulent models. The different slot widths

angles and geometrical profiles

as well as the leading contours of the vane endwall were utilized to analyze their effects on the cooling characteristics of the vane endwall. The numerical results show that slot width has great influence on the cooling characteristics of downstream endwall surface

and it achieves better cooling performance on the downstream endwall surface with the decrease of slot width when the slot flowrate ranges within a certain scope. The angle and structure between slot entrance and downstream endwall surface can significantly affect the cooling characteristics of downstream surface. Smaller angle of slot entrance and downstream endwall surface and smoother structure obtain better cooling performance. The optimized slot downstream endwall profile achieves better cooling performance compared with conventional endwall profile because the optimized slot downstream endwall profile can adjust flow rate distribution via changing the geometry along the pitchwise orientation. The endwall geometry profile with non-dimensional amplitude of 0.75 and phase angle of 30° achieves optimal cooling performance.

关键词

Keywords

references

BOGARD D G, THOLE K A. Gas turbine film cooling [J]. Journal of Propulsion and Power, 2006, 22(2): 249-270.

刘高文, 刘松龄, 朱慧人, 等. 涡轮叶栅前缘上游端壁气膜冷却的传热实验研究 [J]. 航空动力学报, 2001, 16(3): 249-255.

LIU Gaowen, LIU Songling, ZHU Huiren, et al. Endwall heat transfer and film cooling measurement in a turbine cascade with injection upstream of leading edge [J]. Journal of Aerospace Power, 2001, 16(3): 249-235.

SUNDARAM N, THOLE K A. Bump and trench modifications to film cooling holes at the vane-endwall junction [J]. ASME Journal of Turbomachinery, 2008, 130: 041013.

LYNCH S P, THOLE K A. The effect of combustor-turbine interface gap leakage on the endwall heat transfer for a nozzle guide vane [J]. ASME Journal of Turbomachinery, 2008, 130: 041019.

LYNCH S P, KAREN A, THOLE K A. The effect of the combustor-turbine slot and midpassage gap on vane endwall heat transfer [J]. ASME Journal of Turbomachinery, 2011, 133: 041002.

THRIFT A A, THOLE K A, HADA S. Effects of orientation and position of the combustor-turbine interface on the cooling of a vane endwall [J]. ASME Journal of Turbomachinery, 2012, 134: 061019.

张扬, 齐士博, 袁新. 涡轮流场影响端壁气膜冷却的实验研究 [J]. 工程热物理学报, 2011, 32(6): 941-944.

ZHANG Yang, QI Shibo, YUAN Xin. Experimental investigation on the turbine blade platform film cooling effected by the flow field [J]. Journal of Engineering Thermophysics, 2011, 32(6): 941-944.

戴斌, 陈榴, 戴韧. 叶栅端壁气膜孔布局与冷却效果数值分析 [J]. 工程热物理学报, 2013, 34(8): 1429-1433.

DAI Bin, CHEN Liu, DAI Ren. Numerical study on the endwall cooling effects of film-hole allocations [J]. Journal of Engineering Thermophysics, 2013, 34(8): 1429-1433.

高庆, 陶加银, 宋立明, 等. 涡轮轮缘密封封严效率的数值研究 [J]. 西安交通大学学报, 2013, 47(5): 12-17.

GAO Qing, TAO Jiayin, SONG Liming, et al. Numerical investigation on the sealing efficiency of the turbine rim seal [J]. Journal of Xi'an Jiaotong University, 2013, 47(5): 12-17.

MENSCH A, THOLE K A. Overall effectiveness of a blade endwall with jet impingement and film cooling [J]. ASME Journal of Engineering for Gas Turbines and Power, 2014, 136(3): 031901.

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

液氢管路输运中静电积聚机理与电流密度分布特征研究

X射线辐照下聚酰亚胺材料空间电荷分布特性的数值模拟

异质裂隙内超临界CO2地热提取特性数值模拟研究

工质与叶轮传热对超临界二氧化碳向心透平气动性能与流动特性的作用机制

机翼近场尾流流动特性的附着涡模型分析