湿蒸汽条件下空心静叶缝隙抽吸性能的试验研究

李亮 1; 薛太旭 1; 刘启凡 1; 吴晓明 2; 杨建道 1; 2

doi:10.7652/xjtuxb201411001

您当前的位置：

首页 >

文章列表页 >

湿蒸汽条件下空心静叶缝隙抽吸性能的试验研究

更新时间：2025-07-09

- 湿蒸汽条件下空心静叶缝隙抽吸性能的试验研究
- Experimental Research on Water Removal Performance of Hollow Stator Blade in Wet Steam Flow
- 西安交通大学学报 2014年48卷第11期页码：1-7
- 作者机构：
  
  西安交通大学叶轮机械研究所,西安,710049
- 作者简介：
- 基金信息：
- DOI：10.7652/xjtuxb201411001
  中图分类号： TK262
- 网络首发：2014-11-10，
  
  纸质出版：2014
- 稿件说明：
移动端阅览
李亮 1, 薛太旭 1, 刘启凡 1, 等. 湿蒸汽条件下空心静叶缝隙抽吸性能的试验研究[J]. 西安交通大学学报, 2014,48(11):1-7.

Experimental Research on Water Removal Performance of Hollow Stator Blade in Wet Steam Flow[J]. 2014, 48(11): 1-7.
李亮 1, 薛太旭 1, 刘启凡 1, 等. 湿蒸汽条件下空心静叶缝隙抽吸性能的试验研究[J]. 西安交通大学学报, 2014,48(11):1-7. DOI： 10.7652/xjtuxb201411001.

Experimental Research on Water Removal Performance of Hollow Stator Blade in Wet Steam Flow[J]. 2014, 48(11): 1-7. DOI： 10.7652/xjtuxb201411001.

摘要

为获得湿蒸汽流动条件下空心静叶缝隙除湿结构的设计依据

利用湿蒸汽试验平台、在与实际空心静叶工作湿度一致的条件下

对8组不同缝隙位置、形状和宽度的空心静叶进行了缝隙抽吸水膜性能的试验研究。结果表明:缝隙抽吸水膜的特性受到气流马赫数和抽吸差压的综合作用

当抽吸差压增大到一定程度时

缝隙尖角处发生水膜汽化是导致抽吸性能下降的重要因素; 吸力面缝隙位置从0.24倍叶宽变化到0.42倍叶宽时

缝隙抽吸的水量持续增加; 与平直缝隙相比

带台阶过渡的缝隙抽吸性能未提高

反而在马赫数大于0.7时出现显著下降

原因是引起水膜汽化的尖角数目增加; 带圆角过渡的缝隙能有效消除水膜汽化

提高缝隙抽吸水膜的性能; 0.35 mm宽度的缝隙易于使水膜跨过缝隙

2 mm宽度的缝隙不能形成有效的抽吸差压

且均导致缝隙抽吸性能降低; 0.7 mm和1 mm宽度的缝隙均具有良好的抽吸性能

1 mm宽度的缝隙受水膜汽化的影响更小。

Abstract

Aiming at providing guidelines for design of suction slots of hollow stator blade under wet steam flow condition

experiments were implemented on a wet steam test rig with eight hollow stator blades to investigate the water removal performance by varying the position

shape and width of suction slots. The wetness fraction at the inlet section of the test cascade was consistent with the real running condition. It is shown that the amount of removed water is affected by the main flow Mach number and suction pressure difference. When suction pressure difference increases to a moderate value

vaporization of water film occurs and acts as an additional important factor leading to degraded water removal performance. With the position of suction surface slot moving from 0.24 to 0.42 of axial chord

the amount of removed water is continuously increased. Compared with the straight slot

the step-shaped slot cannot improve water removal performance. On the contrary

it results in poor performance when the Mach number is beyond 0.7 due to increased number of sharp corners

which leads to water vaporization. A suction slot with arc-shaped inlet is able to eliminate vaporization of water film and improve water removal performance. A suction slot of 0.35 mm width is apt to allow water film across

a suction slot of 2 mm width cannot form an effective suction pressure difference

and both lead to degraded water removal performance. Suction slots of 0.7 mm and 1 mm width have good water removal performance

but the later is more slightly influenced by water vaporization.

关键词

Keywords

references

蔡颐年. 透平和分离器的双相流[M]. 北京: 机械工业出版社, 1983.

TANUMA T, SAKAMOTO T. The Removal of water from steam turbine stationary blades by suction slots[C]∥Proceedings of IMechE Conference on Turbomachinery. London, UK: IMechE, 1991: 179-189.

王新军, 毛靖儒, 李炎锋, 等. 汽轮机静叶缝隙去水效率的试验研究[J]. 汽轮机技术, 1999, 41(3): 164-168.

WANG Xinjun, MAO Jingru, LI Yanfeng, et al. Experimental investigation on the water removal efficiency from steam turbine stationary blades by suction slot[J]. Turbine Technology, 1999, 41(3): 164-168.

王新军, 李炎锋, 徐廷相. 缝隙宽度对汽轮机空心静叶去水效率影响的实验研究[J]. 西安交通大学学报, 2000, 34(5): 24-27.

WANG Xinjun, LI Yanfeng, XU Tingxiang. Effect of suction slot width on water removal efficiency for steam turbine hollow stationary blades[J]. Journal of Xi'an Jiaotong University, 2000, 34(5): 24-27.

李国春, 王新军, 关盼龙, 等. 汽轮机静叶表面水膜缝隙抽吸的试验研究[J]. 西安交通大学学报, 2009, 43(1): 20-23,33.

LI Guochun, WANG Xinjun, GUAN Panlong, et al. Experimental study on removal of water film from steam turbine stator blade surfaces by suction slots[J]. Journal of Xi'an Jiaotong University, 2009, 43(1): 20-23,33.

徐亮, 颜培刚, 黄洪雁, 等. 汽轮机空心静叶开缝抽吸除湿的数值模拟[J]. 汽轮机技术, 2009, 51(2): 97-99.

XU Liang, YAN Peigang, HUANG Hongyan, et al. Numerical simulation on the suction slot of hollow stationary blade for moisture removal in steam turbine[J]. Turbine Technology, 2009, 51(2): 97-99.

LI L, YANG J, YOU W, et al. Investigation of the vapour-liquid two-phase flow in the low-pressure cylinder of a 1 000 MW nuclear power steam turbine[J]. Proceedings of the Institution of Mechanical: Part A Journal of Power and Energy, 2014, 228(2): 178-185.[本刊相关文献链接]

李瑜,宁德亮,李亮,等.汽轮机中湿汽损失的定量计算.2014,48(1):25-30.[doi:DOI:10.7652/xjtuxb201401005]

程鹏,王新军,张峰,等.核电汽轮机弯管式汽水分离器的改进结构及其除湿性能.2014,48(5):61-66, 77.[doi:10.7652/xjtuxb201405011]

张超,徐自力,刘石,等.采用热固双向耦合模型的转子热应力计算方法研究.2014,48(4):68-72.[doi:10.7652/xjtuxb 201404012]

霍文浩,晏鑫,李军,等.超超临界汽轮机高压缸旁路冷却系统流动特性的研究.2013,47(3):42-47.[doi:10.7652/xjtuxb201303008]

霍文浩,晏鑫,李军,等.超超临界汽轮机高压缸旁路冷却系统冷却特性研究.2013,47(5):24-30.[doi:10.7652/xjtuxb 201305005]

邵帅,邓清华,时和双,等.不同容积流量下汽轮机低压缸末三级定常流动数值研究.2013,47(1):15-20.[doi:10.7652/xjtuxb201301004]

李瑜,李亮,钟刚云,等.末级透平对低压缸气动和凝结特性的影响.2012,46(7):16-20.[doi:10.7652/xjtuxb201207004]

潘家成,徐亮,高建民,等.轴向间距对二次水滴运动特性及沉积规律的影响.2012,46(7):1-6.[doi:10.7652/xjtuxb 201207001]

吴晓明,李国君,丰镇平,等.SST k-ω-kp两相湍流模型及其在湿蒸汽凝结流动数值模拟中的应用.2007,41(5):526-529.[doi:10.7652/xjtuxb200705005]

霍文浩,祁明旭,李军,等.超临界汽轮机中压透平级流动传热特性研究.2011,45(7):9-14.[doi:10.7652/xjtuxb2011 07003]

黄晓明,TARIK Kaya.蒸发毛细弯液面热质传输特征及其稳定性分析.2010,44(3):21-25.[doi:10.7652/xjtuxb2010 03005]

李春国,王新军,关盼龙,等.汽轮机静叶表面水膜缝隙抽吸的试验研究.2009,43(1):20-23.[doi:10.7652/xjtuxb2009 01005]

王新军,卢澄,李振光,等.缝隙吹扫对静叶出口二次水滴直径影响的试验研究.2007,41(7):764-767.[doi:10.7652/xjtuxb200707002]

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

汽轮机静叶表面水膜缝隙抽吸的试验研究

-120 ℃小型逆布雷顿空气制冷机的性能试验研究

SST k-ω-kp两相湍流模型及其在湿蒸汽凝结流动数值模拟中的应用

不同冷却工况下90°带肋通道中蒸汽的强化换热特性研究

玻璃纤维增强复合材料输电塔节点承载力试验研究及有限元分析