饱和氢气加注过程中低温贮箱降温特性及热应力分布的数值研究

朱康 1; 厉彦忠 1; 2; 王磊 1; 文键 1; 李翠 1

doi:10.7652/xjtuxb201405001

您当前的位置：

首页 >

文章列表页 >

饱和氢气加注过程中低温贮箱降温特性及热应力分布的数值研究

更新时间：2025-07-09

- 饱和氢气加注过程中低温贮箱降温特性及热应力分布的数值研究
- Investigation on Cool-Down Behavior and Thermal Stress of Cryogenic Tank During Saturated Hydrogen Gas Filling Process
- 西安交通大学学报 2014年48卷第5期页码：1-7
- 作者机构：
  
  西安交通大学能源与动力工程学院,西安,710049
- 作者简介：
- 基金信息：
  
  : 2013-11-21。作者简介: 朱康(1990—),男,博士生;厉彦忠(通信作者),男,教授,博士生导师。基金项目: 国家自然科学基金资助项目(51376142);教育部高等学校博士学科点专项科研基金资助项目(20100201110012);航天低温推进剂技术国家重点实验室基金资助项目(SKLTSCP1213);中国博士后科学基金资助项目(2013M532041)
- DOI：10.7652/xjtuxb201405001
  中图分类号： TK121
- 网络首发：2014-05-10，
  
  纸质出版：2014
- 稿件说明：
移动端阅览
朱康 1, 厉彦忠 1, 2, 等. 饱和氢气加注过程中低温贮箱降温特性及热应力分布的数值研究[J]. 西安交通大学学报, 2014,48(5):1-7.

Investigation on Cool-Down Behavior and Thermal Stress of Cryogenic Tank During Saturated Hydrogen Gas Filling Process[J]. 2014, 48(5): 1-7.
朱康 1, 厉彦忠 1, 2, 等. 饱和氢气加注过程中低温贮箱降温特性及热应力分布的数值研究[J]. 西安交通大学学报, 2014,48(5):1-7. DOI： 10.7652/xjtuxb201405001.

Investigation on Cool-Down Behavior and Thermal Stress of Cryogenic Tank During Saturated Hydrogen Gas Filling Process[J]. 2014, 48(5): 1-7. DOI： 10.7652/xjtuxb201405001.

摘要

为了获得低温贮箱在饱和氢气加注过程中的降温特性以及箱体壁面的热应力分布

通过计算流体力学软件FLUENT计算了一定加注流量下贮箱内部流体区域的流场、温度场和壁面内的温度场变化

分析了加注过程中贮箱内的流动特性和降温特性; 采用单向流固耦合方法进行壁面热应力分析

得到了3种不同进、出口约束条件下热应力在壁面中的分布以及最大热应力随时间的变化情况

并分析了进、出口弹性支撑约束条件设置的合理性; 考虑贮箱内的压力变化

进行了箱体壁面的综合应力分析。计算结果表明:加注过程可以分为3个阶段

前2个阶段贮箱内部的流场、温度场和壁面温度分布特性依次由入口强制对流和壁面自然对流单独决定

第3阶段由入口强制对流及壁面自然对流共同决定; 在3种不同的约束条件下

箱体壁面中的最大热应力均出现在贮箱加注口和排气口处

在进、出口弹性支撑条件下

壁面最大热应力随时间先增大而后趋于稳定

在稳定应力状态下

热应力的存在使箱体壁面总应力增加了15%左右。

Abstract

A numerical study is performed on the cool-down behavior and thermal stress of a cryogenic tank during the saturated hydrogen gas filling process. CFD simulation is carried out to obtain the flow and temperature distributions inside the tank and the temperature distribution of the tank wall under a specific filling rate. Then the flow and cooling characteristics of the tank during the filling process are analyzed. The thermal stress in the tank wall under three different constraints of the inlet and outlet is calculated with unidirectional fluid-solid coupling method

and the spatial distribution and transient behavior of the thermal stress are revealed. In addition

the rationality of applying elastic supports to the inlet and outlet is demonstrated

and the integrated stress in the tank wall is calculated with the pressure variation in the tank taken into account. Numerical results show that the filling process can be divided into three steps

where the flow and temperature distributions inside the tank are governed by the forced convection from the inlet or the natural convection near the wall in the first and second steps

and by both of them in the third step. The maximum thermal stress appears at the inlet and outlet of the tank under any of the three constraints. For radial elastic support on the inlet and outlet

the maximum thermal stress increases gradually to a steady value and takes up about 15% of the maximum integrated stress in steady state.

关键词

Keywords

references

丁昌, 汪荣顺. ANSYS在低温压力容器应力分析与优化设计中的应用[J]. 低温与超导, 2007, 35(6): 455-457.

DING Chang, WANG Rongshun. Application of ANSYS in stress analysis and optimization design of cryogenic pressure vessels[J]. Cryogenics and Superconductivity, 2007, 35(6): 455-457.

刘占生, 顾卫东, 朱自民, 等. 超临界汽轮机高压缸有限元热应力分析[J]. 汽轮机技术, 2002(2): 23-25.

LIU Zhansheng, GU Weidong, ZHU Zimin, et al. Thermal stress analysis of finite element method of high pressure cylinder of supercritical 600 MW turbine[J]. Turbine Technology, 2002(2): 23-25.

朱鸿梅, 徐烈, 孙恒, 等. 低温粘接技术的应用及热应力分析[J]. 低温与超导, 2004, 32(2): 29-30.

ZHU Hongmei, XU Lie, SUN Heng, et al. The application and thermal stress analysis of cryogenic adhesive bonding technology[J]. Cryogenics and Superconductivity, 2004, 32(2): 29-30.

ZHU Hongmei, SUN Heng, XU Lie, et al. Transient thermal stress analysis of threaded-adhesive joints applied in non-magnetic Dewar[J]. International Journal of Adhesion Adhesives, 2007, 27(8): 621-628.

KIM M G, KANG S G, KIM C G, et al. Thermally induced stress analysis of composite/aluminum ring specimens at cryogenic temperature[J]. Composites Science and Technology, 2008, 68(3): 1080-1087.

KANG S G, KIM M G, KIM C G, et al. Thermo elastic analysis of a type 3 cryogenic tank considering curing temperature and autofrettage pressure[J]. Journal of Reinforced Plastics and Composites, 2008, 27(5): 459-471.

杨世铭, 陶文铨. 传热学[M]. 北京: 高等教育出版社, 2006: 269-270.

HATCH J E. Aluminum: properties and physical metallurgy[M]. Metals Park, Ohio, USA: American Society for Metals, 1984: 6.

DAVIS J R. Aluminum and aluminum alloys[M]. Geauga County, Ohio, USA: ASM International, 1993: 69.

秦叔经. 应力分类概念在压力容器设计中的应用[J]. 化工设备与管道, 2001, 38(5): 5-11.

QIN Shujing. The application of stress classification in the design of pressure vessels[J]. Process Equipment and Piping, 2001, 38(5): 5-11.

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

时序卷积网络在转子热固耦合应力预测及寿命评估中的应用

热-结构耦合作用下压电式力传感器热应力分析

热应力对金属棒料内部损伤的机理研究

火箭发动机液氢预冷回路非稳态传热特性研究

物理气相传输（PVT)法生长碳化硅的晶体形态热应力分析