隔膜压缩机二指数母线膜腔型面设计及实验验证

李霁阳 1; 赵晓华 2; 贾晓晗 1; 彭学院 1

doi:10.7652/xjtuxb201404022

您当前的位置：

首页 >

文章列表页 >

隔膜压缩机二指数母线膜腔型面设计及实验验证

更新时间：2025-04-29

- 隔膜压缩机二指数母线膜腔型面设计及实验验证
- Design and Experimental Verification for Diaphragm Compressor Cavity Profile by Two Exponential Terms Generatrix
- 西安交通大学学报 2014年48卷第4期页码：127-132
- 作者机构：
  
  西安交通大学能源与动力工程学院,西安,710049
- 作者简介：
- 基金信息：
  
  : 2013-07-17。作者简介: 李霁阳(1990—),男,硕士生;贾晓晗(通信作者),男,博士,讲师。基金项目: 国家科技重大专项资助项目(2012ZX06903012)
- DOI：10.7652/xjtuxb201404022
  中图分类号： TH456
- 网络首发：2014-04-10，
  
  纸质出版：2014
- 稿件说明：
移动端阅览
李霁阳 1, 赵晓华 2, 贾晓晗 1, 等. 隔膜压缩机二指数母线膜腔型面设计及实验验证[J]. 西安交通大学学报, 2014,48(4):127-132.

Design and Experimental Verification for Diaphragm Compressor Cavity Profile by Two Exponential Terms Generatrix[J]. 2014, 48(4): 127-132.
李霁阳 1, 赵晓华 2, 贾晓晗 1, 等. 隔膜压缩机二指数母线膜腔型面设计及实验验证[J]. 西安交通大学学报, 2014,48(4):127-132. DOI： 10.7652/xjtuxb201404022.

Design and Experimental Verification for Diaphragm Compressor Cavity Profile by Two Exponential Terms Generatrix[J]. 2014, 48(4): 127-132. DOI： 10.7652/xjtuxb201404022.

摘要

针对广泛使用的单指数母线膜腔型面进行了优化计算

分析了该型面的特点和不足

同时以增大膜腔容积、降低膜片应力为目标

提出了二指数母线膜腔型面。该二指数母线膜腔型面下的膜片径向应力峰值在膜片半径的中间及边缘处

这样可以避开与膜片中心区域附加应力叠加

使得膜片中心区域油侧和气侧面上的径向应力相同且均处于一个较低的水平。对比研究结果表明:在相同膜腔半径、相同膜片材料及膜片内应力均达到许用应力条件下

二指数母线膜腔容积相比单指数增大6.6%; 在相同膜腔半径、相同膜腔容积及相同膜片材料情况下

二指数母线膜腔下膜片最大径向应力相比单指数降低10.0%

膜片中心区域最大径向应力降低11.8%。

Abstract

The traditional generatrix of cavity profile is optimized and the characteristics of the traditional generatrix are discussed. A new generatrix of cavity profile of diaphragm compressor is presented for increasing cavity volume and decreasing diaphragm radial stress. With the new generatrix

the peak values of the diaphragm radial stresses occur in the middle of radius and edge

thus the radial stress in the diaphragm center gets lower. To verify the design theory for cavity profile

the radial stresses of the diaphragm oil side in the cavities with the new and traditional generatrices were tested

and the experimental radial stresses agree well with the theoretical ones. Additionally

the volumes of the cavities with different generatrices and the radial stress distribution of the diaphragm are theoretically analyzed. The results show that the cavity volume with the new generatrix is enlarged by 6.6% than that with the traditional generatrix under the same design conditions. The maximal radial stress in the cavity with the new generatrix decreases by 10.0% and the maximal radial stress in the centric region decreases by 11.8%.

关键词

Keywords

references

MANFRED D. Hofer diaphragm compressors[DB/OL].[2013-03-08]. http:∥www.andreas-hofer.de/E/downloads/diaphragmcompressor10-02.pdf.

郁永章, 刘勇. 特种压缩机[M]. 北京: 机械工业出版社, 1989: 35-37.

徐文强. 隔膜压缩机在HCNG站的运用[J]. 产业与科技论坛, 2012, 11(6): 98-99.

XU Wenqiang. Application of diaphragm compressor in HCNG station[J]. Industrial Science Tribune, 2012, 11(6): 98-99.

王迪生, 冯海芃. 隔膜压缩机双函数构造膜腔曲面[J]. 西安交通大学学报, 1989, 23(3): 25-32.

WANG Disheng, FENG Haipeng. Design of diaphragm chamber curve surface shape with double function of a diaphragm compressor[J]. Journal of Xi'an Jiaotong University, 1989, 23(3): 25-32.

班立兵. 隔膜式压缩机膜腔曲面的优化研究[D]. 北京: 中国科学院力学研究所, 1998.

吴波, 吴立志, 王兴国, 等. 隔膜压缩机膜腔型线的分析研究[J]. 压缩机技术, 2008(4): 1-4.

WU Bo, WU Lizhi, WANG Xingguo, et al. Analysis and study on the diaphragm cavity profile of diaphragm compressors[J]. Compressor Technology, 2008(4): 1-4.

吴立志, 王兴国, 肖云锋. 基于ABAQUS的隔膜压缩机膜片有限元分析[J]. 北京石油化工学院学报, 2008, 16(4): 13-16.

WU Lizhi, WANG Xingguo, XIAO Yunfeng. FEM analysis with ABAQUS on the diaphragm in a diaphragm compressor[J]. Journal of Beijing Institute of Petro-chemical Technology, 2008, 16(4): 13-16.

ALTUKHOV S M, ZHUKOV A V. Determining the geometric parameters of the compression chamber of a diaphragm compressor with a hydraulic drive[J]. Chemical and Petroleum Engineering, 1986, 22(7): 309-312.

KALSHNIKOV V F, KUZNETSOV V D, ANTONOVA L I. Calculation of the reliability of a compressor diaphragm under variable loading[J]. Chemical and Petroleum Engineering, 1987, 23(4): 168-170.

IVANOV B A, NARKUNSKII S E, PLESHAKOV V F. Selection of materials for high pressure oxygen diaphragm compressors[J]. Chemical and Petroleum Engineering, 1981, 17(6): 306-308.

薛大为. 板壳理论[M]. 北京: 北京工业学院出版社, 1988: 81-91.

顾惠君. 隔膜压缩机典型故障分析[J]. 煤炭技术, 2009, 28(10): 26-27.

GU Huijun. Typical fracture analysis of diaphragm compressor[J]. Coal Technology, 2009, 28(10): 26-27.

唐学敏. 隔膜压缩机金属隔膜故障原因分析及对策[J]. 机械, 2010, 37(S1): 77-78.

TANG Xuming. Analysis and treatment on the fracture of the diaphragm in the diaphragm compressor[J]. Machinery, 2010, 37(S1): 77-78.

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

微透镜阵列热压印应力与脱模温度研究

直埋供热管道直角弯管热-力耦合分析

燃气轮机周向拉杆转子拉杆应力分析和改进设计

隧道内燃料电池汽车氢气泄漏扩散特性及影响因素

EBSILON软件在热电联产系统优化中的应用综述