微型气浮轴承高速透平膨胀机的研制

陈汝刚; 侯予; 陈纯正

您当前的位置：

首页 >

文章列表页 >

微型气浮轴承高速透平膨胀机的研制

更新时间：2025-07-09

- 微型气浮轴承高速透平膨胀机的研制
- study of Miniature High Speed Turboexpander with Gas Lubricated Bearing
- 西安交通大学学报 2010年44卷第1期页码：61-65
- 作者机构：
  
  西安交通大学能源与动力工程学院,西安,710049
- 作者简介：
- 基金信息：
  
  : 2009-09-01. 作者简介: 陈汝刚(1970-),男,博士,讲师. 基金项目: 民用航天预先研究资助项目(C3220061314);新世纪优秀人才支持计划资助项目(NCET-05-0834);西安交通大学校长科研基金支持计划项目(08140010)
- DOI：
  中图分类号： TB653
- 网络首发：2010-01-10，
  
  纸质出版：2010
- 稿件说明：
移动端阅览
陈汝刚, 侯予, 陈纯正. 微型气浮轴承高速透平膨胀机的研制[J]. 西安交通大学学报, 2010,44(1):61-65.

study of Miniature High Speed Turboexpander with Gas Lubricated Bearing[J]. 2010, 44(1): 61-65.
陈汝刚, 侯予, 陈纯正. 微型气浮轴承高速透平膨胀机的研制[J]. 西安交通大学学报, 2010,44(1):61-65. DOI：

study of Miniature High Speed Turboexpander with Gas Lubricated Bearing[J]. 2010, 44(1): 61-65. DOI：

摘要

为了发展微型气体轴承高速透平

在优化设计的基础上

研制了国内首台轴径为6 mm、叶轮直径为9 mm、设计转速为300 000 r/min的微型气体轴承透平膨胀机.对研制样机进行了全面介绍

阐述了该研制样机的结构设计特点

并对研制样机进行了初步的机械性能和热力性能考核.通过转子起浮试验

系统机械性能、热力性能的连续运转及超速试验考核

结果显示:所研制的样机振动小、运转平稳、效率高

最高转速超过342 000 r/min

满足超速15%的要求; 在室温为23 ℃、无回热器的情况下

当进气压力从0升到0.27 MPa的45 min升速时间内

温降就达42 ℃

具有降温速度快

降温效果显著的特点.由于其机械及热力性能均达到预期要求

因此为今后进一步发展我国微型高速气体轴承透平机械奠定了坚实基础.

Abstract

A new miniature static gas bearing turboexpander with a shaft diameter of 6mm

a wheel diameter of 9mm

and a designed rotation speed of 300 000 r/min was developed on the basis of optimum design. The structure characteristics of the prototype developed were investigated. The preliminary mechanical and thermodynamic performance of the prototype was experimentally examined. The results show that the prototype has obvious features such as small vibration

stable operation and high efficiency

and the prototype can run at more than 342 000 r/min reaching 15% over-speed. Moreover

the temperature drop can be 42 ℃ within 45 minutes when the driving pressure increases from 0 to 0.27 MPa at the room temperature of 23 ℃ for the prototype without recuperators. The experimental verification shows that the mechanical and thermodynamic performance of the prototype can meet the requirement.

关键词

Keywords

references

EVANS J C, NELLIS G F. Design and test of hydrostatic gas Bearings for a hybrid cryogenic refrigerator[C]∥ ASME International Mechanical Engineering Congress. Washington, USA:ASME, 2003:67-76.

WAUMANS T, VLEUGELS P, PEIRS J, et al. Rotor dynamic behavior of a micro-turbine rotor on air bearings: modeling techniques and experimental verification [C]∥ Proceedings of International Conference on Noise and Vibration Engineering. Lenven, Belgium: Katholieke Universiteit Leuven, 2006: 181-198.

KOUSUKE I, MOTOHIDE M, SUSUMU T, et al. Experimental verification of the feasibility of a 100W class micro-scale gas turbine at an impeller diameter of 10 mm [J]. Journal of Micromechanics and Micro Engineering, 2006, 16(9):254-261.

KOUSUKE I, SHUJI T, SHINICHI T, et al. Development of high-speed micro-gas bearings for three-dimensional micro-turbo machines [J]. Journal of Micromechanics and Micro Engineering, 2005, 15(9):222-227.

SHUJI T, KOUSUKE I, SHINICHI T, et al. Turbo test rig with hydroinertia air bearings for a palmtop gas turbine [J].Journal of Micromechanics and Microengineering, 2004, 14(11):1449-1454.

EPSTEIN A H. Millimeter-scale, micro-electro-mechanical systems gas turbine engines [J].ASME Journal of Engineering for Gas Turbines and Power, 2004, 126(2):205-226.

EHRICH F F, JACOBSON S A. Development of high-speed gas bearings for high-power density microdevices [J]. ASME Journal of Engineering for Gas Turbines and Power, 2003,125(1):141-148.

小型低温余热发电系统膨胀机输出特性试验研究.2009,43(11):100-103.

培尔顿式膨胀机的实验研究.2009,43(9):95-99.

低温余热回收用涡旋膨胀机性能模拟研究.2009,43(7):95-99.

CO2滑片膨胀机热力过程的试验研究.2008,42(3):313-317.

低温透平制冷机的静压气体润滑轴承研究.2007,41(7):792-796.

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

高速透平膨胀机临界转速的计算与分析

新型箔片动压止推气体轴承承载特性的试验研究

掌上透平弹性箔片动压气体轴承的试验研究

温度影响下箔片动压止推轴承分析

箔片安装位置对气体轴承性能影响的仿真分析