直角法兰双辊夹持扩旋成形有限元模型的确定

范淑琴; 赵升吨; 张琦; 王春辉

您当前的位置：

首页 >

文章列表页 >

直角法兰双辊夹持扩旋成形有限元模型的确定

更新时间：2025-07-09

- 直角法兰双辊夹持扩旋成形有限元模型的确定
- Finite Element Model Determination of Double Rollers Clamping Expanding Spinning for Right-Angle Flange
- 西安交通大学学报 2010年44卷第5期页码：66-70
- 作者机构：
  
  西安交通大学机械工程学院,西安,710049
- 作者简介：
- 基金信息：
  
  : 2009-09-02. 作者简介: 范淑琴(1977-),女,博士生;赵升吨(联系人),男,教授,博士生导师. 基金项目:国家自然科学基金资助项目(50905137);科技部科技人员服务企业行动项目(2009GJG00029)
- DOI：
  中图分类号： TG306
- 网络首发：2010-05-10，
  
  纸质出版：2010
- 稿件说明：
移动端阅览
范淑琴, 赵升吨, 张琦, 等. 直角法兰双辊夹持扩旋成形有限元模型的确定[J]. 西安交通大学学报, 2010,44(5):66-70.

Finite Element Model Determination of Double Rollers Clamping Expanding Spinning for Right-Angle Flange[J]. 2010, 44(5): 66-70.
范淑琴, 赵升吨, 张琦, 等. 直角法兰双辊夹持扩旋成形有限元模型的确定[J]. 西安交通大学学报, 2010,44(5):66-70. DOI：

Finite Element Model Determination of Double Rollers Clamping Expanding Spinning for Right-Angle Flange[J]. 2010, 44(5): 66-70. DOI：

摘要

为了得到适合于直角法兰双棍夹持扩旋成形模拟的有限元模型

基于ABAQUS/Explicit平台

针对常用的工件转动与不转动的建模方法

建立了2种直角法兰双辊夹持扩旋成形有限元模型.利用这2种模型对旋压成形过程分别进行了数值模拟

从旋辊轨迹、动态效应、计算时间、计算结果等方面比较分析了2种模型对双棍夹持扩旋成形模拟的影响.数值模拟结果表明

工件转动模型得到的最大等效应力应变偏大

而采用工件不转动模型不仅可以提高计算精度

而且可有效地降低计算时间

因此最终确定工件不转动模型为所研究的最佳有限元模型.

Abstract

To obtain the reasonable model of double rollers clamping expanding spinning

based on ABAQUS/Explicit

two models are established in case of unrotating rotating workpiece. Following the two models

the forming process for right-angle flange is analyzed. And then the effects of two models on simulation are investigated in terms of roller path

dynamic effects

computing time and computing results. Compared with the model for rotating workpiece

the model for unrotating workpiece enables to improve the calculation accuracy and shorten computing period. Although stress and stain distributions of the two models are similar at the same place of the workpiece

the equivalent stress and strain values obtained from the model for rotating workpiece get greater. It is verified that the model for unrotating workpiece is the optimal one to simulate double rollers clamping expanding spinning process with finite element method.

关键词

Keywords

references

LIU Jianhua, YANG He, LI Y Q. A study of stress and strain distributions of first-pass conventional spinning under different roller traces [J]. Journal of Materials Processing Technology, 2002, 129(1/3): 326-329.

QUIGLEY E, MONAGHAN J. The finite element modeling of conventional spinning using multi-domain models [J]. Journal of Materials Processing Technology, 2002,124(3): 360-365.

XIA Qinxiang, XIE Shiwei, HUO Y L, et al. Numerical simulation and experimental research on the multi-pass neck-spinning of non-axisymmetric offset tube [J]. Journal of Materials Processing Technology, 2008, 206(1/3): 500-508.

LIU Chunho. The simulation of the multi-pass and die-less spinning process [J]. Journal of Materials Processing Technology, 2007,192/193:518-524.

SEBASTIANI G, BROSIUS A, EWERS R, et al. Numerical investigation on dynamic effects during sheet metal spinning by explicit finite-element-analysis [J]. Journal of Materials Processing Technology, 2006, 177(1/3): 401-403.

ZHAN Mei, YANG He, ZHANG Jinhui, et al. 3D FEM analysis of influence of roller feed rate on forming force and quality of cone spinning [J]. Journal of Materials Processing Technology, 2007, 187/188: 486-491.

BAI Qian, YANG He, ZHAN Mei. Finite element modeling of power spinning of thin-walled shell with hoop inner rib [J]. Transactions of Nonferrous Metals Society of China, 2008, 18(1): 6-13.

孙丽丽,聂爱琴,胡小建,等.汽车轮毂旋压成形过程的有限元数值模拟 [J]. 合肥工业大学学报,2008, 31(4):552-555.

SUN Lili, NIE Aiqin, HU Xiaojian,et al. FE numerical simulation of automobile hub spinning forming process [J]. Journal of Hefei University of Technology, 2008, 31(4):552-555.

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

21-6-9高强不锈钢管数控弯曲回弹对材料参数的敏感性

直埋供热管道直角弯管热-力耦合分析

双金属复合管直角法兰双辊夹持旋压起皱分析

电子级超纯氮深冷空分流程节能优化研究

采用试验设计方法的第三代CO2气体箔轴承箔片几何参数敏感性分析