熔滴喷射沉积制造中重熔过程的研究

杨毅; 齐乐华; 曾祥辉; 罗俊; 杨方

您当前的位置：

首页 >

文章列表页 >

熔滴喷射沉积制造中重熔过程的研究

更新时间：2025-07-09

- 熔滴喷射沉积制造中重熔过程的研究
- Study of Remelting During Droplet Spray Depositing Process
- 西安交通大学学报 2010年44卷第8期页码：117-121
- 作者机构：
  
  西北工业大学机电学院,西安,710072
- 作者简介：
- 基金信息：
  
  : 2010-01-04. 作者简介: 杨毅(1985-),男,硕士生;齐乐华(联系人),女,教授,博士生导师. 基金项目: 国家“863计划”资助项目(2008AA03A238);高等学校博士学科点专项科研基金资助项目(20070699076);全国优秀博士学位论文作者专项基金资助项目(2007B3)
- DOI：
  中图分类号： O242;TG455
- 网络首发：2010-08-10，
  
  纸质出版：2010
- 稿件说明：
移动端阅览
杨毅, 齐乐华, 曾祥辉, 等. 熔滴喷射沉积制造中重熔过程的研究[J]. 西安交通大学学报, 2010,44(8):117-121.

Study of Remelting During Droplet Spray Depositing Process[J]. 2010, 44(8): 117-121.
杨毅, 齐乐华, 曾祥辉, 等. 熔滴喷射沉积制造中重熔过程的研究[J]. 西安交通大学学报, 2010,44(8):117-121. DOI：

Study of Remelting During Droplet Spray Depositing Process[J]. 2010, 44(8): 117-121. DOI：

摘要

为使熔滴喷射增材制造过程中熔滴颗粒间能够获得较好的融合

分析了熔滴温度和基体温度对颗粒间重熔过程的影响

建立了基于Stefan条件的熔滴融合时界面重熔过程的一维热传导模型; 利用有限元方法对模型进行求解

得到了熔滴喷射沉积过程中液固界面的移动规律和最大重熔深度

并以此预测了沉积熔滴间的结合效果.在自行研制的熔滴沉积实验系统中进行了柱状制件沉积实验

结果表明:提高基板温度或熔滴温度可有效增加重熔深度

进而改善熔滴间的结合状态; 所建模型可以正确预测颗粒间的结合效果.

Abstract

To determine the conditions for fine metallurgical bonding

a one-dimensional heat transfer model based on Stefan boundary condition was established to investigate the effects of droplets and substrate temperature on remelting. The liquid-solid interface movement and remelting depth were calculated

and the bonding of droplets in pillar component was predicted via numerical simulation. Following the simulation results

a droplet spray experiment device was designed

and some pillar components were deposited. Both experimental and simulation results demonstrate that increasing either droplet temperature or substrate temperature facilitates the bonding between deposited droplets.

关键词

Keywords

references

SUDARSHAM S T, SUDARSHAN S T. Rapid solidification technology: an engineering guide [M]. Labcaster, Pennsylvania, USA: Technomic Publising Company, Inc., 1993:3-10.

胥光申, 赵万华, 卢秉恒. 高分辨率快速成型系统的光固化实验研究[J]. 西安交通大学学报, 2005,39(1):66-69.

XU Guangshen, ZHAO Wanhua, LU Bingheng. Experimental investigation on high-resolution stereolithography system [J]. Journal of Xi'an Jiaotong University, 2005,39(1):66-69.

LUO Jun, QI Lehua, JIANG Xiaoshan, et al. Research on lateral instability of the uniform-charged droplet stream during droplet-based freeform fabrication [J]. International Journal of Machine Tools and Manufacture, 2008,48(3/4):289-294.

AMON C H, SCHMALTZ K S, MERZ R, et al. Numerical and experimental investigation of interface bonding via substrate remelting of an impinging molten metal droplet [J]. ASME Journal of Heat Transfer, 1996, 118(1):164-172.

NEAGU M. Study of remelting process during the droplet-based solid freeform fabrication [J]. The Annals Dunarea de Jos University of Galati, Fascicle V: Technologies in Mechanical Engineering, 2004,5:35-39.

FANG M, CHANDRA S, PARK C B. Building three-dimensional objects by deposition of molten metal droplets [J]. Rapid Prototyping Journal, 2008,14(1): 44-52.

SIQUEIRA C A, CHEUNG N, GARCIA A. The columnar to equiaxed transition during solidification of Sn-Pb alloys [J]. Journal of Alloys and Compounds, 2003, 351(1/2):126-134.

ZENG Xianghui, QI Lehua, HUANG Hua. Experimental research of pneumatic drop-on-demand high temperature droplet deposition for rapid prototyping [C]∥SU Daizhong. Advanced Design and Manufacture: II. Zurich, Switzerland: Trans Tech Publications Ltd., 2009:405-408.

MAHESH N S, MENDANCA J, MURALIDHARA M K, et al. Modeling of droplet dynamic and thermal behaviour during spray deposition [J]. Bulletin of Materials Science, 2003,26(3):355-364.

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

金属熔滴气动按需喷射特性试验研究

隧道内燃料电池汽车氢气泄漏扩散特性及影响因素

扇贝仿生密封腔室内超临界二氧化碳泄漏流湍动能耗散机理研究

不同板叠材料热声热机能量转换过程数值模拟研究

面向高海拔空冷发电机防晕性能演化规律的电热耦合研究