绝缘栅双极型晶体管脉冲工作时结温特性及温度分布研究

陈明; 胡安; 唐勇; 汪波

您当前的位置：

首页 >

文章列表页 >

绝缘栅双极型晶体管脉冲工作时结温特性及温度分布研究

更新时间：2025-07-09

- 绝缘栅双极型晶体管脉冲工作时结温特性及温度分布研究
- Investigation on Junction Temperature Characteristic and Temperature Distribution Detection for Pulsed IGBT Operation
- 西安交通大学学报 2012年46卷第4期页码：70-76
- 作者机构：
  
  海军工程大学舰船综合电力技术国防科技重点实验室,武汉,430033
- 作者简介：
- 基金信息：
  
  : 2011-07-10. 作者简介: 陈明(1982-),男,博士生;胡安(通信作者),男,教授,博士生导师. 基金项目: 国家自然科学基金重点资助项目(50737004)
- DOI：
  中图分类号： TM322
- 网络首发：2012-04-10，
  
  纸质出版：2012
- 稿件说明：
移动端阅览
陈明, 胡安, 唐勇, 等. 绝缘栅双极型晶体管脉冲工作时结温特性及温度分布研究[J]. 西安交通大学学报, 2012,46(4):70-76.

Investigation on Junction Temperature Characteristic and Temperature Distribution Detection for Pulsed IGBT Operation[J]. 2012, 46(4): 70-76.
陈明, 胡安, 唐勇, 等. 绝缘栅双极型晶体管脉冲工作时结温特性及温度分布研究[J]. 西安交通大学学报, 2012,46(4):70-76. DOI：

Investigation on Junction Temperature Characteristic and Temperature Distribution Detection for Pulsed IGBT Operation[J]. 2012, 46(4): 70-76. DOI：

摘要

建立了电热耦合和损耗热场耦合计算模型

采用该模型

获得了相同外部条件下的绝缘栅双极型晶体管(IGBT)芯片结温波动特性及温度分布特征

完成了使用红外热成像实时探测短时脉冲工作方式下IGBT芯片表面温度波动及分布特性的预测.探测结果表明

在一定散热条件和占空比不大的情况时

短时脉冲间歇等非周期瞬态工作方式下芯片表面温度快速上升之后

进入一个缓慢的上升周期

实验也表明

在特殊工作场合时可突破器件手册推荐使用的最大电流值.利用建立的热分析模型

还可以实现对不同工作方式下器件结壳温差和结温波动幅度的预测.

Abstract

The junction temperature characteristic fluctuation and temperature distribution profiles of the IGBT power module under transient impulse intermittent operation with the same external operation condition is analyzed for different simulation models

which is implemented by the power loss and temperature field coupling relation. The distribution of temperature profiles on the chip surface is detected by a high-speed mid-wave infrared imaging camera. The real time detection shows that under transient pulse intermittent operation the temperature of the chip surface rises quickly and then slowly for a certain heat sink situation and little duty ratio

while the junction temperature drops quickly in the intermittent time

and it is possible to breaking the restriction of the peak operational current. The simulation models are applied to predicting junction-case temperature drop and fluctuation characteristic of junction under temperature different working conditions.

关键词

Keywords

references

LU Hua, BAILEY C, YIN Chunyan. Design for reliability of power electronics modules[J]. Microelectronics Reliability, 2009, 49(9/10/11): 1250-1255.

KHATIBI G, WROCZEWSKI W, WEISS B, et al. A fast mechanical test technique for Life time estimation of micro-joints[J]. Microelectronics Reliability, 2008, 48(11/12): 1822-1830.

LEFRANC G, MITIC G, LICHT T. Properties of solders and their fatigue in power modules[J]. Microelectronics Reliability, 2002, 42(9/10/11): 1641-1646.

BRYANT A T, MAWBY P A, PALMER P R, et al. Exploration of power device reliability using compact device models and fast electrothermal simulation[J]. IEEE Transactions on Industry Applications, 2008, 44(3): 894-903.

WEI Lixiang, LUKASZEWSKI R A, LIPO T A. Analysis of power-cycling capability of IGBT modules in a conventional matrix converter[J]. IEEE Transactions on Industry Applications, 2009, 45(4): 1443-1451.

BOUARROUDJ M, KHATIR Z, OUSTEN J P, et al. Degradation behavior of 600 V-200 A IGBT modules under power cycling and high temperature environment conditions[J]. Microelectronics Reliability, 2007, 47(9/10/11): 1719-1724.

AMRO R, LUTZ J, LINDEMANN A. Power cycling with high temperature swing of discrete components based on different technologies[C]∥Proceeding of 35th IEEE Power Electronics Specialists Conference. Piscataway, NJ, USA: IEEE, 2004: 2593-2598.

ONUKI J, KOIZUMI M, SUWA M. Reliability of thick Al wire bonds in IGBT modules for traction motor drives[J]. IEEE Transactions on Advanced Packaging, 2000, 23(1): 108-112.

MAURO C. Selected failure mechanisms of modern power modules[J]. Microelectronics Reliability, 2002, 42(4/5): 653-667.

SOLOMALALA P, SAIZ J, MERMET-GUYENNET M, et al. Virtual reliability assessment of integrated power switches based on multi-domain simulation approach[J]. Microelectronics Reliability, 2007, 47(9/10/11): 1343-1348.

FELLER L, HARTMANN S, SCHNEIDER D. Lifetime analysis of solder joints in high power IGBT modules for increasing the reliability for operation at 150℃[J]. Microelectronics Reliability, 2008, 48(9): 1161-1166.

HEFNER A J. A dynamic electro-thermal model for the IGBT[J]. IEEE Transactions on Industry Applications, 1994, 30(2): 394-405.

FABIS P M, SHUM D, WINDISCHMANN H. Thermal modeling of diamond-based power electronics packaging[C]∥Proceeding of Fifteenth IEEE Semiconductor Thermal Measurement and Management Symposium. Piscataway, NJ, USA: IEEE, 1999: 98-104.

LIM D J, PULKO S H. Characterisation of heat spreader materials for pulsed IGBT operation[J]. IET Circuits, Devices and Systems, 2007, 1(2): 126-136.

FAIR H D. Electric launch science and technology in the United States[J]. IEEE Transactions on Magnetics, 2003, 39(1): 11-17.

KAYE R J. Operational requirements and issues for coilgun EM launchers[J]. IEEE Transactions on Magnetics, 2005, 41(1): 194-199.

COVA P, FANTINI F. On the effect of power cycling stress on IGBT modules[J]. Microelectronics Reliability, 1998, 38(6/7/8): 1347-1352.

SANKARAN V A, CHEN C, AVANT C S, et al. Power cycling reliability of IGBT power modules[C]∥Conference Record of Thirty-Second IEEE Industry Applications Society Annual Meeting. Piscataway, NJ, USA: IEEE, 1997: 1222-1227.

CLEMENTE S. Transient thermal response of power semiconductors to short power pulses[J]. IEEE Transactions on Power Electronics, 1993, 8(4): 337-341.

YUN Chansu, MALBERTI P, CIAPPA M, et al. Thermal component model for electrothermal analysis of IGBT module systems[J]. IEEE Transactions on Advanced Packaging, 2001, 24(3): 401-406.

陈明,胡安,唐勇,等.绝缘栅双极型晶体管传热模型建模分析[J].高电压技术,2011, 37(2):453-459.

CHEN Ming, HU An, TANG Yong, et al. Modeling analysis of IGBT thermal model[J]. High Voltage Engineering, 2011, 37(2): 453-459.

华伟,周文定.现代电力电子器件及其应用[M].北京:北方交通大学出版社,2002:175-176.

KRAUS R, MATTAUSCH H J. Status and trends of power semiconductor device models for circuit simulation[J]. IEEE Transactions on Power Electronics, 1998, 13(3): 452-465.

SOFIA J W. Electrical temperature measurement using semiconductors[J]. Electronics Cooling, 1997, 3(1): 22-25.

唐勇,陈明,汪波.电力电子器件短时脉冲工作的结温特性研究[J].电力电子技术,2010, 44(3):88-90.

TANG Yong, CHEN Ming, WANG Bo. Research on junction temperature characteristic of power electronics devices under short pulse operation[J]. Power Electronic, 2010, 44(3): 88-90.

陈明,胡安,刘宾礼.绝缘栅双极型晶体管失效机理与寿命预测模型分析[J].西安交通大学学报, 2011, 45(10): 65-71.

CHEN Ming, HU An, LIU Binli. Investigation on failure mechanism and lifetime prediction modeling of IGBT power electronic devices[J].Journal of Xi'an Jiaotong University,2011,45(10):65-71.

绝缘栅双极型晶体管失效机理与寿命预测模型分析. 2011,45(10):65-71.

等离子活化烧结过程的温度分布研究. 2011,45(1):122-126.

电压反转极性对温度梯度场下聚乙烯内空间电荷的影响. 2011,45(10):54-58.

移动数字电视调谐器中低噪声模拟滤波器的设计. 2009,43(2):72-76.

有机电致发光器件的热传导特性研究. 2009,43(4):70-74.

局部放电脉冲群的实用快速分类技术及应用. 2008,42(8):1021-1025.

环氧及其复合材料气固界面快脉冲闪络特性. 2008,42(6):703-707.

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

考虑轴颈同步涡动的转子-轴承系统热效应分析

等离子活化烧结过程的温度分布研究

扇形射流的空气动力学特性

绝缘栅双极型晶体管失效机理与寿命预测模型分析

高温功率循环下绝缘栅双极型晶体管失效特征及机理分析