新型智能材料微小型光学镜头致动器的设计与性能研究

王延杰; 王永泉; 陈花玲; 朱子才; 罗斌

您当前的位置：

首页 >

文章列表页 >

新型智能材料微小型光学镜头致动器的设计与性能研究

更新时间：2025-05-08

- 新型智能材料微小型光学镜头致动器的设计与性能研究
- Design and Performance Investigation for Miniature Optical Lens IPMC Actuators
- 西安交通大学学报 2012年46卷第5期页码：79-84+142
- 作者机构：
  
  西安交通大学机械工程学院,西安,710049
- 作者简介：
- 基金信息：
  
  : 2011-10-24. 作者简介: 王延杰(1985-),男,博士生;王永泉(通信作者),男,讲师. 基金项目: 教育部博士学科点专项科研基金资助项目(20090201110037);中央高校基本科研业务费专项资金资助项目
- DOI：
  中图分类号： TB381;TP212
- 网络首发：2012-05-10，
  
  纸质出版：2012
- 稿件说明：
移动端阅览
王延杰, 王永泉, 陈花玲, 等. 新型智能材料微小型光学镜头致动器的设计与性能研究[J]. 西安交通大学学报, 2012,46(5):79-84+142.

Design and Performance Investigation for Miniature Optical Lens IPMC Actuators[J]. 2012, 46(5): 79-84+142.
王延杰, 王永泉, 陈花玲, 等. 新型智能材料微小型光学镜头致动器的设计与性能研究[J]. 西安交通大学学报, 2012,46(5):79-84+142. DOI：

Design and Performance Investigation for Miniature Optical Lens IPMC Actuators[J]. 2012, 46(5): 79-84+142. DOI：

摘要

为了使微小型光学镜头驱动系统满足低能耗、高稳定性以及结构简单的要求

采用新型智能材料IPMC设计了一种微小型的光学镜头致动器

并对其输出力、位移及响应速度等性能进行了研究.根据直线驱动要求确定了瓣形和环形结构; 通过化学还原方法制备了IPMC材料

采用激光切割技术分别制作出5种形状的环形和瓣形致动器

并对其性能进行了测试.利用有限元软件

通过等效热模型分析了致动器的基本性能

结果表明:实验测试与理论分析结果一致

误差率在10%以内; 瓣形致动器的总体位移性能比环形致动器的好; 在3 V驱动电压下两者的位移均大于200 μm; 当内圆半径为2 mm、瓣数为8时

致动器的最大位移与响应速度均最佳.

Abstract

To meet the requirements of low consumption

high stability and simplicity for the optical lens driving system

ionic polymer-metal composite(IPMC)

a new kind of intelligent material is adopted to design a miniature optical lens actuator

and its output force

displacement

and response speed are investigated respectively. For the purpose of linear driving

two kinds of actuating structures

the petal-shaped and annular structures are determined. Then

IPMC is prepared by chemical reduction method and five kinds of petal-shaped and annular actuators are manufactured by laser cutting and their performances are tested. The performances of the actuators with different structure parameters are analyzed using an equivalent thermal model via software FEA. The analytical results coincide well with the experimental ones with error less than 10%

and the displacement performance of petal-shaped actuator is better than that of the annular one. Under actuation voltage of 3 V

both actuators can get displacement over 200 μm. The annular actuator with an inner radius of 2 mm and the petal-shaped actuator with 8 petals achieve better performances in both displacement and response speed.

关键词

Keywords

references

罗玉元,李朝东,张国贤.基于离子聚合物金属复合结构(IPMC)柔性致动器的研究[J].中国机械工程, 2006, 4(2): 410-413.

LUO Yuyuan, LI Chaodong, ZHANG Guoxian. Study on soft actuators based on ion-exchange polymer metal composites(IPMC)[J]. China Mechanical Engineering, 2006, 4(2): 410-413.

宗光华,裴旭,于靖军,等.一种新型柔性直线导向机构及其运动精度分析[J].光学精密工程, 2008, 16(4): 630-636.

ZONG Guanghua, PEI Xu, YU Jingjun et al. Novel compliant linear guiding mechanism and analysis of kinetic precision [J]. Optics and Precision Engineering, 2008, 16(4): 630-636.

EAMEX Co. トピツクス[EB/OL]. [2011-05-26]. http:∥www.eamex.co.jp.

LEE H K, CHOIA N J, JUNG S K, et al. Application of ionic polymer-metal composites for auto-focusing compact camera modules [C/OL]∥Proceedings of SPIE, 2008, Vol. 6927. [2011-05-13]. http:∥spiedigitallibrary. org/proceedings/resource/2/psisdg/6927/1/69271N_1.

KIM S J, KIM C J, PARK N C, et al. Design and position control of AF lens actuator for mobile phone using IPMC-EMIM [C/OL]∥Proceedings of SPIE, 2008, Vol. 6927. [2011-05-13]. http:∥144.206.159.178/FT/CONF/16413491/16413538.pdf.

KIM S J, KIM C J, PARK N C, et al. Design and control of 2-axis tilting actuator for endoscope using ionic polymer metal composites [C/OL]∥Proceedings of SPIE, 2009, Vol. 7290.[2011-05-21].http:∥spiedigitallibrary.org/proceedings/resource/2/psisdg/7290/1/729005_1isAuthorized=no.

SHIMIZU I, KIKUCHI K, TSUCHITANI S. Variable-focal length lens using IPMC [C/OL]∥ICROS-SICE International Joint Conference, 2009. [2011-05-21]. http:∥ieeexplore.ieee.org/xpl/freeabs_all.jsp?arnumber=533434.

ZHU Zicai, CHEN Hualing, CHANG Longfei, et al. Influence of fabrication process steps on Pd-IPMC electrode morphologies and mechano-electrical properties [C/OL]∥ Proceedings of SPIE, 2011, Vol.7976.[2011-05-13]. http:∥link.aip.org/link/?PSISDG/7976/79762T/1.

PAQUETTE J W, KIM K J, NAM J D, et al. An equivalent model for ionic polymer-metal composites and their performance improvement by a clay-based polymer nano-composite technique [J]. Journal of Intelligent Material Systems and Structures, 2003, 14(10): 633-642.

LEE S, PARK H C, KIM K J. Equivalent modeling for ionic polymer-metal composite actuators based on beam theories [J]. Smart Materials Structures, 2005, 14(6): 1363-1368.

李龙土,邬军飞,褚祥诚,等.压电双晶片的有限元分析及实验[J].光学精密工程, 2008, 16(12): 2378-2383.

LI Longtu, WU Junfei, CHU Xiangcheng, et al. Finite element analysis and experiment on piezoelectric bimorph [J]. Optics and Precision Engineering, 2008, 16(12): 2378-2383.

安逸,熊克,顾娜.采用梯度功能方法的 IPMC弹性模量改进模型[J]. 复合材料学报, 2009, 26(6): 189-193.

AN Yi, XIONG Ke, GU Na. Improved model of IPMC's elastic modulus using functionally gradient method [J]. Acta Materiae Compositae Sinica, 2009, 26(6): 189-193.

SHOJI E, HIRAYAMA D. Effects of humidity on the performance of ionic polymer-metal composite actuators: experimental study of the back-relaxation of actuators [J]. Phys Chem: B, 2007, 111(41): 11915-11920.

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

电致动聚合物致动器的动态响应研究

扇贝仿生密封腔室内超临界二氧化碳泄漏流湍动能耗散机理研究

隧道内燃料电池汽车氢气泄漏扩散特性及影响因素

多工况下离心压气机叶轮-机匣一体联合设计优化

采用机器学习的大规模并行程序I/O性能建模与预测方法