花键轴增量式滚轧成形工艺的分流方式及温度效应研究

李泳峄; 赵升吨; 范淑琴; 孙振宇

您当前的位置：

首页 >

文章列表页 >

花键轴增量式滚轧成形工艺的分流方式及温度效应研究

更新时间：2025-07-09

- 花键轴增量式滚轧成形工艺的分流方式及温度效应研究
- Research on Divided Flow Method and Temperature Effect of the Incremental Rolling Forming Process for Spline Shaft
- 西安交通大学学报 2012年46卷第9期页码：60-65
- 作者机构：
  
  西安交通大学机械工程学院,西安,710049
- 作者简介：
- 基金信息：
  
  : 2012-02-15. 作者简介: 李泳峄(1986-),男,博士生;赵升吨(通信作者),男,教授,博士生导师. 基金项目: 国家自然科学基金资助项目(50975222)
- DOI：
  中图分类号： TG302;TG306
- 网络首发：2012-09-10，
  
  纸质出版：2012
- 稿件说明：
移动端阅览
李泳峄, 赵升吨, 范淑琴, 等. 花键轴增量式滚轧成形工艺的分流方式及温度效应研究[J]. 西安交通大学学报, 2012,46(9):60-65.

Research on Divided Flow Method and Temperature Effect of the Incremental Rolling Forming Process for Spline Shaft[J]. 2012, 46(9): 60-65.
李泳峄, 赵升吨, 范淑琴, 等. 花键轴增量式滚轧成形工艺的分流方式及温度效应研究[J]. 西安交通大学学报, 2012,46(9):60-65. DOI：

Research on Divided Flow Method and Temperature Effect of the Incremental Rolling Forming Process for Spline Shaft[J]. 2012, 46(9): 60-65. DOI：

摘要

为了降低花键轴增量式滚轧成形工艺中工件初始直径对滚轧载荷和齿形填充质量的负面影响

根据分流锻造思想提出了一种齿顶分流方式

分析了温度效应对滚轧载荷和齿形填充质量的影响

并通过DEFORM-3D有限元软件对该分流方式进行了数值分析验证.研究结果表明:在校正滚轧阶段

齿顶分流方式的应用使得花键轴增量式滚轧成形工艺中滚轧载荷最大值平均下降了约60%

并降低了工件初始直径对花键轴齿形填充质量和齿距累计误差的影响.工件材料在400、800、1 000 ℃(相对室温20 ℃)时

温度效应使得最大滚轧载荷分别平均下降了约20%、67%、80%

并且明显提高了齿形处工件材料的填充质量.

Abstract

To reduce the negative effect of initial workpiece diameter on the rolling load and tooth filling quality

a tooth divided flow method is put forward according to the thought of divided flow forging

and the relevant numerical analysis and verification are conducted with DEFORM-3D. Furthermore

the temperature effect on the rolling load and tooth filling quality is investigated. The results show that after the tooth divided flow method is applied

the maximum rolling load during calibrating phase can be lowered by 60% averagely

the tooth filling quality and pitch cumulative error can be improved obviously. Due to the temperature effect

the maximum rolling load is reduced by 20%

67% and 80% respectively under 400 ℃

800 ℃ and 1 000 ℃ compared with the case under material temperature of 20 ℃

and also the tooth filling quality is improved.

关键词

Keywords

references

关文达.汽车构造 [M]. 3版. 北京: 机械工业出版社, 2010: 224-427.

CHILDS P R N. Mechanical Design [M]. 2nd ed. Oxford, UK: Elsevier Butterworth-Heinemann, 2004: 79-101.

KLEPIKOV V V, BODROV A N. Precise shaping of splined shafts in automobile manufacturing [J]. Russian Engineering Research, 2003, 23(12): 37-40.

崔凤奎,李言,李春梅.渐开线花键加工方法进展 [J]. 矿山机械, 2007, 35(2): 116-119.

CUI Fengkui, LI Yan, LI Chunmei. The fabricating methods of cold rolling for involute spline shafts [J]. Mining Processing Equipment, 2007, 35(2): 116-119.

ZHANG Dawei, LI Yongtang, FU Jianhua, et al. Mechanics analysis on precise forming process of external spline cold rolling [J]. Chinese Journal of Mechanical Engineering, 2007, 20(3): 54-58.

王明福,付建华,刘志奇,等.花键冷滚压成形过程有限元分析 [J].锻压技术, 2010, 35(4): 155-159.

WANG Mingfu, FU Jianhua, LIU Zhiqi, et al. Finite element analysis of spline cold roll forming process [J]. Forging Stamping Technology, 2010, 35(4): 155-159.

刘志奇,宋建丽,李永堂,等.渐开线花键冷滚压精密成形工艺分析及试验研究 [J]. 机械工程学报, 2011,47(14): 32-38.

LIU Zhiqi, SONG Jianli, LI Yongtang, et al. Analysis and experimental study on the precision cold rolling process of involute spline [J]. Journal of Mechanical Engineering, 2011, 47(14):32-38.

顾科建,彭晓南,刘飞.基于ANSYS渐开线花键冷搓成形的数值模拟 [J]. 河南科技大学学报: 自然科学版, 2008, 29(2): 20-24.

GU Kejian, PENG Xiaonan, LIU Fei. Numerical simulation of cold roll forming of involute spline by ANSYS [J]. Journal of Henan University of Science and Technology: Natural Science, 2008, 29(2): 20-24.

NEUGEBAUER R, PUTZ M, HELLFRITZSCH U. Improved process design and quality for gear manufacturing with flat and round rolling [J]. Annals of the CIRP, 2007, 56(1): 307-312.

KONDO K, OHGA K. Precision cold die forging of a ring gear by divided flow method [J]. International Journal of Machine Tools and Manufacture, 1995, 35(8): 1105-1113.

寇淑清,杨慎华,黄良驹,等.用约束分流法冷锻成形高精度直齿圆柱齿轮 [J]. 吉林工业大学学报:自然科学版, 2004, 30(2): 19-23.

KOU Shuqing, YANG Shenhua, HUANG Liangju, et al. The applications of constrained divided-flow technique to cold precision forging spur gears [J]. Journal of Jilin University of Technology: Natural Science, 2004, 30(2): 19-23.

FLUHRER J. DEFORMTM-3D version 6.0 user's manual [M]. Columbus, USA: Scientific Forming Technologies Corporation, 2006.

LIN Yongcheng, CHEN Mingsong, ZHONG Jue. Effect of temperature and strain rate on the compressive deformation behavior of 42CrMo steel [J]. Journal of Materials Processing Technology, 2008, 205(1/3):308-315.

WARRINGTON C, KAPOOR S, DEVOR R. Finite element modeling for tap design improvement in form tapping [J]. ASME Journal of Manufacturing Science and Engineering, 2006, 128(1):65-73.

内啮合摆线转子压缩机型线连续性条件研究. 2009,43(1): 34-37.

气压熔融挤压快速成形材料及成形工艺研究. 2010,44(1): 100-104.

不同压力下Ti3SiC2陶瓷的干摩擦磨损性能研究. 2011,45(2): 121-124.

43″汽轮机叶片材料热变形行为及制坯工艺参数优化. 2011,45(1): 94-98.

自润滑活塞环的热胀失效研究. 2011,45(5): 90-93.

尺寸效应对纳米银杆拉伸力学特性的影响. 2006,40(1): 101-105.

轧机机架参数敏感性分析及顺序优化的研究. 2008,42(1): 1-4.

相关衰落多输入多输出系统的参数化信道估计. 2007,41(12): 1431-1435.

面向缩聚模型的结构损伤识别研究. 2011,45(9): 101-107.

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

EBSILON软件在热电联产系统优化中的应用综述

融合物理信息与深度算子网络的变压器绕组热-流场快速计算方法

超临界二氧化碳向心透平轮背间隙内风阻损失及流动特性研究

混合电解槽阵列协同的风光耦合制氢系统双层多目标优化

不同板叠材料热声热机能量转换过程数值模拟研究