Numerical Study on Deposition Characteristics of Soot Particles in Impeller of a Multi-Blade Centrifugal Fan

doi:10.7652/xjtuxb202405013

您当前的位置：

首页 >

文章列表页 >

Numerical Study on Deposition Characteristics of Soot Particles in Impeller of a Multi-Blade Centrifugal Fan

更新时间：2025-07-28

- Numerical Study on Deposition Characteristics of Soot Particles in Impeller of a Multi-Blade Centrifugal Fan
- Vol. 58, Issue 5, Pages: 133-142(2024)
- 作者机构：
  
  1. 西安交通大学能源与动力工程学院,西安,710049
  2. 健康智慧厨房浙江省工程研究中心,浙江,宁波,315336
- 作者简介：
- 基金信息：
- DOI：10.7652/xjtuxb202405013
  CLC： TK83
- Published：2024
- 稿件说明：
移动端阅览
Numerical Study on Deposition Characteristics of Soot Particles in Impeller of a Multi-Blade Centrifugal Fan[J]. 2024, 58(5): 133-142.
DOI：

Numerical Study on Deposition Characteristics of Soot Particles in Impeller of a Multi-Blade Centrifugal Fan[J]. 2024, 58(5): 133-142. DOI： 10.7652/xjtuxb202405013.

摘要

为了揭示多翼离心风机内部油性粒子沉积分布规律

减少风机内粒子沉积

采用Fluent离散相模型描述粒子运动

同时结合临界速度模型和用户自定义函数(UDF)建模油性粒子在壁面上的沉积

模拟研究了多翼离心风机内油性粒子的运动轨迹和沉积特性

并探究了颗粒直径对沉积分布的影响。结果表明:油性粒子沉积主要分布在叶片压力面

且靠近出口尾缘段尤为严重; 由于进气条件不稳定

整机下内部流场更为紊乱

沉积情况也更为严重; 大直径粒子受惯性力主导更容易沉积在叶片表面。针对油性粒子沉积分布规律及成因

提出了切割叶片减小叶片出口安装角从而减少叶轮内油性粒子沉积的方法。对于切割后的叶片

叶轮出口处流动分离区域减小

叶片尾缘段涡量减小

通过数值模拟和实验研究发现

叶轮内油性粒子沉积率分别下降了30.75%和30.66%

两者吻合良好

证实了提出的减小叶轮油性粒子沉积方法的有效性。

Abstract

To reveal the distribution of soot particle deposition in a multi-blade centrifugal fan and mitigate such deposition

numerical simulations are conducted to investigate the trajectories and deposition characteristics of soot particles within a multi-blade centrifugal fan. The study utilizes the Fluent discrete phase model to describe particle motion

while employing the critical velocity model and the user-defined functions(UDF)to model the particle deposition on walls. In addition

the study examines the particle diameter on deposition distribution. Findings indicate that soot particles mainly deposit on the blade pressure surface

with notable accumulation near the trailing edge close to the outlet. When the complete machine is involved

the flow field within the fan becomes more turbulent due to unstable inflow conditions

thereby leading to escalating deposition levels. It is found that particles with larger diameters exhibit a higher tendency to deposit on blade surfaces owing to the dominant inertial forces. In light of deposition distributions and their causal factors

an optimization strategy is proposed to reduce the deposition on blade surfaces by cutting blades and consequently reducing the outlet installation angle. In terms of the modified blades

flow separation near the impeller outlet decreases

leading to decreased vorticity around the trailing edge of blades. Comparing the original and modified blades

numerical simulation results show a 30.75% decrease in deposition rate

while experimental outcomes demonstrate a 30.66% reduction. The close agreement underscores the effectiveness of the proposed method in mitigating the deposition of soot particles.

关键词

Keywords

references

LUN Yuxin, LIN Limin, HE Haijiang, et al. Effects of vortex structure on performance characteristics of a multiblade fan with inclined tongue [J]. Proceedings of the Institution of Mechanical Engineers: Part A Journal of Power and Energy, 2019, 233(8): 1007-1021.

WEI Yikun, ZHU Lingling, ZHANG Wei, et al. Numerical and experimental investigations on the flow and noise characteristics in a centrifugal fan with step tongue volutes [J]. Proceedings of the Institution of Mechanical Engineers: Part C Journal of Mechanical Engineering Science, 2020, 234(15): 2979-2993.

ZHANG Yingkun, LI Kunhang, LI Yunlong, et al. Effects of the guiding tank on flow characteristics inside the double-suction squirrel-cage fan for range hood [J]. International Journal of Fluid Machinery and Systems, 2020, 13(1): 203-213.

马列, 刘阳, 刘小民. 采用吸力面仿鱼形叶片的多翼离心风机气动性能研究 [J]. 风机技术, 2022, 64(2): 9-16.

MA Lie, LIU Yang, LIU Xiaomin. Study on the aerodynamic performance of multi-blade centrifugal fan with the suction surface bionic fish blades [J]. Chinese Journal of Turbomachinery, 2022, 64(2): 9-16.

王加浩, 龚东巧, 刘小民, 等. 采用仿鲤科鱼C型启动构型叶片的多翼离心风机气动性能研究 [J]. 西安交通大学学报, 2022, 56(9): 57-68.

WANG Jiahao, GONG Dongqiao, LIU Xiaomin, et al. Aerodynamic performance of multi-blade centrifugal fan with bionic blades inspired by C-Type start of cyprinidae [J]. Journal of Xi'an Jiaotong University, 2022, 56(9): 57-68.

王梦豪, 吴立明, 刘小民, 等. 采用仿鸮翼叶片降低空调用离心风机气动噪声的研究 [J]. 西安交通大学学报, 2018, 52(6): 55-61.

WANG Menghao, WU Liming, LIU Xiaomin, et al. A study on noise reduction of centrifugal fan in air conditioner by using the bionic blade inspired by the owl wing [J]. Journal of Xi'an Jiaotong University, 2018, 52(6): 55-61.

孟永哲, 许子倩, 刘小民. 多翼离心风机模化设计中叶轮-蜗壳的匹配性研究 [J]. 风机技术, 2022, 64(3): 10-16.

MENG Yongzhe, XU Ziqian, LIU Xiaomin. Study on the matching of impeller and volute in the modeling design of multi-blade centrifugal fan [J]. Chinese Journal of Turbomachinery, 2022, 64(3): 10-16.

SREEDHARAN S S, TAFTI D K. Composition dependent model for the prediction of syngas ash deposition in turbine gas hotpath [J]. International Journal of Heat and Fluid Flow, 2011, 32(1): 201-211.

BRACH R M, DUNN P F. A mathematical model of the impact and adhesion of microsphers [J]. Aerosol Science and Technology, 1992, 16(1): 51-64.

JOHNSON K L, KENDALL K, ROBERTS A D. Surface energy and the contact of elastic solids [J]. Proceedings of the Royal Society of London: A Mathematical and Physical Sciences, 1971, 324(1558): 301-313.

EL-BATSH H, HASELBACHER H. Effect of turbulence modeling on particle dispersion and deposition on compressor and turbine blade surfaces [C]//ASME Turbo Expo 2000: Power for Land, Sea, and Air. New York, NY, USA: ASME, 2000: V001T03A084.

JENSEN J W, SQUIRE S W, BONS J P, et al.Simulated land-based turbine deposits generated in an accelerated deposition facility [J]. Journal of Turbomachinery, 2005, 127(3): 462-470.

AI Weiguo, MURRAY N, FLETCHER T H, et al. Effect of hole spacing on deposition of fine coal flyash near film cooling holes [J]. Journal of Turbomachinery, 2012, 134(4): 041021.

LAYCOCK R, FLETCHER T H.Independent effects of surface and gas temperature on coal fly ash deposition in gas turbines at temperatures up to 1 400 ℃ [J]. Journal of Engineering for Gas Turbines and Power, 2016, 138(2): 021402.

SMITH C, BARKER B, CLUM C, et al.Deposition in a turbine cascade with combusting flow [C]//ASME Turbo Expo 2010: Power for Land, Sea, and Air. New York, NY, USA: ASME, 2010: 743-751.

BONILLA C, CLUM C, LAWRENCE M, et al.The effect of film cooling on nozzle guide vane deposition [C]//ASME Turbo Expo 2013: Turbine Technical Conference and Exposition. New York, NY, USA: ASME, 2013: V03BT13A043.

CASADAY B, PRENTER R, BONILLA C, et al.Deposition with hot streaks in an uncooled turbine vane passage [J]. Journal of Turbomachinery, 2014, 136(4): 041017.

王飞龙, 何雅玲, 汤松臻, 等. 典型烟气余热换热器气侧积灰特性 [J]. 科学通报, 2017, 62(12): 1292-1301.

WANG Feilong, HE Yaling, TANG Songzhen, et al. Numerical study of fouling characteristics on two kinds of typical heat exchangers used in the waste heat recovery systems [J]. Chinese Science Bulletin, 2017, 62(12): 1292-1301.

贾会霞, 席光, 闻苏平. 轴流压缩机转子叶栅内粒子沉积及对其性能影响的数值研究 [J]. 工程热物理学报, 2004, 25(5): 779-782.

JIA Huixia, XI Guang, WEN Suping. Numerical simulation of particle deposition and performance deterioration in axial compressor rotors [J]. Journal of Engineering Thermophysics, 2004, 25(5): 779-782.

周君辉, 张靖周. 涡轮叶栅内粒子沉积特性的数值研究 [J]. 航空学报, 2013, 34(11): 2492-2499.

ZHOU Junhui, ZHANG Jingzhou. Numerical investigation on particle deposition characteristic inside turbine cascade [J]. Acta Aeronautica et Astronautica Sinica, 2013, 34(11): 2492-2499.

杨晓军, 胡英琦, 徐致远, 等. 存在剥离条件下颗粒物沉积过程的数值研究和实验验证 [J]. 推进技术, 2019, 40(7): 1523-1535.

YANG Xiaojun, HU Yingqi, XU Zhiyuan, et al. Experimental validation and numerical simulation of particles depositional processes with detachment [J]. Journal of Propulsion Technology, 2019, 40(7): 1523-1535.

YANG Xing, HAO Zihan, FENG Zhenping. Variations of cooling performance on turbine vanes due to incipient particle deposition [J]. Proceedings of the Institution of Mechanical Engineers: Part A Journal of Power and Energy, 2021, 235(8): 1832-1846.

郝子晗, 杨星, 丰镇平. 高压涡轮动叶机匣颗粒物沉积效应的非定常数值研究 [J]. 工程热物理学报, 2023, 44(5): 1244-1252.

HAO Zihan, YANG Xing, FENG Zhenping. Unsteady simulations of deposition effects on the casing of a rotor passage in a high-pressure turbine [J]. Journal of Engineering Thermophysics, 2023, 44(5): 1244-1252.

CASADAY B P, AMERI A A, BONS J P. Numerical investigation of ash deposition on nozzle guide vane endwalls [J]. Journal of Engineering for Gas Turbines and Power, 2013, 135(3): 032001.

BONILLA C, WEBB J, CLUM C, et al.The effect of particle size and film cooling on nozzle guide vane deposition [J]. Journal of Engineering for Gas Turbines and Power, 2012, 134(10): 101901.

ROZATI A, TAFTI D K, SREEDHARAN S S. Effects of syngas ash particle size on deposition and erosion of a film cooled leading edge [J]. Journal of Turbomachinery, 2011, 133(1): 011010.

LUNDGREEN R, SACCO C, PRENTER R, et al. Temperature effects on nozzle guide vane deposition in a new turbine cascade rig [C]//ASME Turbo Expo 2016: Turbomachinery Technical Conference and Exposition. New York, NY, USA: ASME, 2016: V05AT13A021.

杨晓军, 祝佳雄. 涡轮叶栅通道内颗粒物沉积过程的数值模拟 [J]. 航空学报, 2017, 38(5): 31-42.

YANG Xiaojun, ZHU Jiaxiong. Numerical simulation of particle deposition process inside turbine cascade [J]. Acta Aeronautica et Astronautica Sinica, 2017, 38(5): 31-42.

徐致远. 涡轮端壁处颗粒物沉积的数值研究 [D]. 天津: 中国民航大学, 2018.

WHITAKER S M, LUNDGREEN R K, BONS J P.Effects of metal surface temperature on deposition-induced flow blockage in a vane leading edge cooling geometry [C]//ASME Turbo Expo 2017: Turbomachinery Technical Conference and Exposition. New York, NY, USA: ASME, 2017: V02DT48A020.

MENSCH A, THOLE K.Simulations of multiphase particle deposition on a gas turbine endwall with impingement and film cooling [J]. Journal of Turbomachinery, 2015, 137(11): 111002.

吕浪. 燃气透平静叶微颗粒碰撞和沉积特性的数值分析 [D]. 广州: 华南理工大学, 2018.

周君辉, 张靖周. 气膜孔附近粒子沉积特性的数值研究 [J]. 航空动力学报, 2014, 29(9): 2166-2173.

ZHOU Junhui, ZHANG Jingzhou. Numerical investigation on particle deposition characteristics in vicinity of film cooling holes [J]. Journal of Aerospace Power, 2014, 29(9): 2166-2173.

赵传鹏, 刘松, 谭晓茗, 等. 气膜冷却射流对叶片微细颗粒沉积影响 [J]. 航空动力学报, 2022, 37(3): 545-554.

ZHAO Chuanpeng, LIU Song, TAN Xiaoming, et al. Effect of film cooling jet on deposition of micro particles on blades [J]. Journal of Aerospace Power, 2022, 37(3): 545-554.

AI Weiguo, FLETCHER T H. Computational analysis of conjugate heat transfer and particulate deposition on a high pressure turbine vane [J]. Journal of Turbomachinery, 2012, 134(4): 041020.

雷健, 秦国良, 吴彦东, 等. 多翼离心风机出口涡旋成因分析与抑制方法 [J]. 流体机械, 2022, 50(12): 65-71.

LEI Jian, QIN Guoliang, WU Yandong, et al. Cause analysis and suppression method of outlet vortex of multi-blade centrifugal fan [J]. Fluid Machinery, 2022, 50(12): 65-71.

熊仲营, 邓稼琦, 王梦豪, 等. 蜗舌改型设计对多翼离心风机气动性能的影响 [J]. 风机技术, 2018, 60(6): 31-37.

XIONG Zhongying, DENG Jiaqi, WANG Menghao, et al. Study on effects of modified volute tongue on the performance of a multi-blade centrifugal fan [J]. Chinese Journal of Turbomachinery, 2018, 60(6): 31-37.

叶舟, 王企鲲, 郑胜. 离心通风机蜗舌及出口流场的数值模拟分析 [J]. 风机技术, 2008(5): 15-19.

YE Zhou, WANG Qikun, ZHENG Sheng. Analysis on volute tongue and outlet flow field of centrifugal fan by numerical simulation [J]. Chinese Journal of Turbomachinery, 2008(5): 15-19.

张辉辉. 厨房颗粒物分布运动规律及数值分析 [D]. 哈尔滨: 哈尔滨工业大学, 2016.[40] 裴钰. 燃气轮机涡轮叶片表面污染物沉积模型研究 [D]. 天津: 中国民航大学, 2016.

于思琦, 吴大转, 杨帅. 叶片出口角对多翼离心风机性能影响的数值研究 [J]. 流体机械, 2019, 47(11): 1-7.

YU Siqi, WU Dazhuan, YANG Shuai. Numerical study on the influence of blade outlet angle on the performance of multi-blade centrifugal fan [J]. Fluid Machinery, 2019, 47(11): 1-7.

刘路. 多翼离心风机叶轮的结构优化研究 [D]. 杭州: 浙江工业大学, 2009.

ZHANG Jiankun, LIU Haihu. Multi-objective optimization of aerodynamic and erosion resistance performances of a high-pressure turbine [J]. Energy, 2023, 277: 127731.

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Numerical and Experimental Study on the Effects of Curved Volute on the Aerodynamic Noise of Multi-Blade Centrifugal Fans

Numerical Analysis of Spray Cooling Characteristics in Superheated Steam Pipelines

Study on Effects of Double-Arc Non-Uniform Blades on the Flow Control and Aerodynamic Performance of Multi-Blade Centrifugal Fan

Noise Reduction Mechanism of Single-Arc Bionic Blade with Wave Shape Leading Edge Coupled with Serrated Trailing Edge

Effects of Bionic Volute Tongue Bioinspired by Leading Edge of Owl Wing on Aerodynamic Performance and Noise of Multi-Blade Centrifugal Fan

Related Author

LIU Xiaomin

HE Xinkui

JIANG Jiwu

TIAN Chenye

PENG Xiaokang

MA Yanpeng

JIANG Can

CUI Longhao

Related Institution

西安交通大学能源与动力工程学院，710049，西安School of Energy and Power Engineering, Xi'an Jiaotong University, Xi'an 710049, China

美的集团厨房和热水事业部，528311，广东佛山Midea Group Kitchen and Hot Water Division, Foshan, Guangdong 528311, China

School of Future Technology, Xi'an Jiaotong University

School of Energy and Power Engineering, Xi'an Jiaotong University

Media HVAC and Building Technologies Division Research and Development Center

⁰