Study on the Grinding and Polishing Application of Abrasive Particle-Reinforced Magnetorheological Elastomer

GUO Lei; JI Yunxiao; MA Zhen; GUO Wanjin; LEE Chulhee; ZHANG Xinrong

doi:10.7652/xjtuxb202310014

您当前的位置：

首页 >

文章列表页 >

Study on the Grinding and Polishing Application of Abrasive Particle-Reinforced Magnetorheological Elastomer

更新时间：2025-05-08

- Study on the Grinding and Polishing Application of Abrasive Particle-Reinforced Magnetorheological Elastomer
- Vol. 57, Issue 10, Pages: 143-152(2023)
- 作者机构：
  
  1. 长安大学工程机械学院,西安,710064
  2. 中国科学院西安光学精密机械研究所,西安,710119
  3. 仁荷大学机械工程系,仁川,韩国,22212
- 作者简介：
- 基金信息：
- DOI：10.7652/xjtuxb202310014
  CLC： TG58
- Online First：10 October 2023，
  
  Published：2023
- 稿件说明：
移动端阅览
GUO Lei, JI Yunxiao, MA Zhen, et al. Study on the Grinding and Polishing Application of Abrasive Particle-Reinforced Magnetorheological Elastomer[J]. 2023, 57(10): 143-152.
DOI：

GUO Lei, JI Yunxiao, MA Zhen, et al. Study on the Grinding and Polishing Application of Abrasive Particle-Reinforced Magnetorheological Elastomer[J]. 2023, 57(10): 143-152. DOI： 10.7652/xjtuxb202310014.

摘要

针对常规刚性磨具对复杂面型、硬脆难加工材料工件进行磨抛加工时

难以兼顾加工效率、表面质量以及完整性的问题

提出了一种基于磨料颗粒增强磁流变弹性体材料(A-MRE)的磨抛加工方法。首先

基于磁性颗粒与磨料颗粒在硅橡胶基体中的链网组装与夹持行为

设计了A-MRE材料制备工艺流程; 然后

基于微观组织结构观测

建立了A-MRE材料代表体积单元(RVE)模型

结合理论分析与有限元仿真研究了磁场条件对基体软固结磨粒把持行为的影响; 最后

采用A-MRE磨具对SiC材料开展磨抛加工实验

分析了不同磁场条件下的表面加工质量与材料去除效率。研究结果表明:磁场方向与A-MRE基体磁性颗粒链方向夹角为0°时磨粒把持应力最大

且随磁场强度的增加而增大

对A-MRE基体施加1.5 μm压缩量时

磨粒最大把持应力可达396.63 kPa; 磁场强度为0.35 T时

采用A-MRE磨具加工的SiC材料表面粗糙度比无磁场条件下的降低了80.3%

材料去除效率提高了28.6%

磨具损耗量降低了56.1%

验证了A-MRE作为弹性磨具基体材料的可行性。

Abstract

As conventional rigid abrasive tools struggle to balance machining efficiency

surface quality and integrity when used to deal with hard and brittle materials with complex surface features

a novel abrasive machining method

which used abrasive particle-reinforced magnetorheological elastomer(A-MRE)

was proposed in this study. Firstly

a preparation process of A-MRE was designed

considering the chain network assembly behavior of magnetic particles and abrasive grains in the silicone rubber matrix. Then

a representative volume element(RVE)model was established through the observation of microscopic structure. The effect of a magnetic field on the holding behavior of softness consolidation abrasive grains was investigated through theoretical analysis and fem simulation. Finally

an experimental SiC material abrasive machining was carried out using A-MRE tools

and the surface quality and material removal rate were analyzed under different magnetic field conditions. The research results show that the maximum abrasive grain holding stress occurs when the magnetic field direction and the chain direction of the magnetic particles form a 0° angle

and the stress increases with higher magnetic field intensities. When applying a compressive strain of 1.5 μm to the A-MRE tool

the maximum holding stress reaches 396.63 kPa. Comparing the A-MRE tool's machining performance to the case without a magnetic field

it is observed that employing a magnetic field intensity of 0.35 T leads to an 80.3% reduction in SiC material's surface roughness

a 28.6% increase in material removal

and a 56.1% reduction in tool wear. These findings confirm the feasibility of A-MRE as the material of elastic abrasive tools.

关键词

Keywords

references

袁巨龙, 王金虎, 吕冰海, 等. 力流变抛光技术 [J]. 机械工程学报, 2022, 58(15): 21-30.

YUAN Julong, WANG Jinhu, LÜ Binghai, et al. Force rheological polishing technology [J]. Journal of Mechanical Engineering, 2022, 58(15): 21-30.

刘锋伟, 吴永前, 陈强, 等. 大口径光学非球面镜先进制造技术概述 [J]. 光电工程, 2020, 47(10): 63-85.

LIU Fengwei, WU Yongqian, CHEN Qiang, et al. Overview of advanced manufacturing technology of large-aperture aspheric mirror [J]. Opto-Electronic Engineering, 2020, 47(10): 63-85.

SHARMA A, KALSIA M, UPPAL A S, et al. Machining of hard and brittle materials: a comprehensive review [J]. Materials Today: Proceedings, 2022, 50, Part 5: 1048-1052.

李华, 任坤, 殷振, 等. 超声振动辅助磨料流抛光技术研究综述 [J]. 机械工程学报, 2021, 57(9): 233-253.

LI Hua, REN Kun, YIN Zhen, et al. Review of ultrasonic vibration-assisted abrasive flow polishing technology [J]. Journal of Mechanical Engineering, 2021, 57(9): 233-253.

GHOSH G, SIDPARA A, BANDYOPADHYAY P P. Review of several precision finishing processes for optics manufacturing [J]. Journal of Micromanufacturing, 2018, 1(2): 170-188.

李敏, 胡玲. CBN多孔砂轮制备方法与修整技术的研究进展 [J]. 金属材料与冶金工程, 2016, 44(3): 8-14.

LI Min, HU Ling. Progress of fabrication and dressing methods for CBN porous grinding wheel [J]. Metal Materials and Metallurgy Engineering, 2016, 44(3): 8-14.

徐西鹏, 黄辉, 胡中伟, 等. 磨粒工具的研究现状及发展趋势 [J]. 机械工程学报, 2022, 58(15): 2-20.

XU Xipeng, HUANG Hui, HU Zhongwei, et al. Development of abrasive tools: state-of-the-art and prospectives [J]. Journal of Mechanical Engineering, 2022,58(15): 2-20.

ZHANG Shaojian, ZHOU Yuanping, ZHANG Haijun, et al. Advances in ultra-precision machining of micro-structured functional surfaces and their typical applications [J]. International Journal of Machine Tools and Manufacture, 2019, 142: 16-41.

邓家云, 潘继生, 张棋翔, 等. 单晶SiC基片的化学机械抛光技术研究进展 [J]. 金刚石与磨料磨具工程, 2020, 40(1): 79-91.

DENG Jiayun, PAN Jisheng, ZHANG Qixiang, et al. Research progress in chemical mechanical polishing of single crystal SiC substrates [J]. Diamond Abrasives Engineering, 2020, 40(1): 79-91.

BASTOLA A K, HOSSAIN M. A review on magneto-mechanical characterizations of magnetorheological elastomers [J]. Composites: Part B Engineering, 2020, 200: 108348.

QIAO Yanliang, ZHANG Jiangtao, ZHANG Mei, et al. A magnetic field-and frequency-dependent dynamic shear modulus model for isotropic silicone rubber-based magnetorheological elastomers [J]. Composites Science and Technology, 2021, 204: 108637.

李旭. 磁流变弹性体的力-磁耦合本构模型 [D]. 绵阳: 中国工程物理研究院, 2017.

孙书蕾. 磁流变体有限变形数值模拟及本构建模研究 [D]. 西安: 西北工业大学, 2015.

LIAN Chenglong, LEE K H, LEE C H. Friction and wear characteristics of magneto-rheological elastomers based on silicone/polyurethane hybrid [J]. Journal of Tribology, 2015, 137(3): 031607.

XU Zhiqiang, WANG Jun, WANG Qiuliang, et al. Investigation of the polishing mechanism of magnetorheological elastic polishing composites [J]. The International Journal of Advanced Manufacturing Technology, 2022, 118(1): 377-389.

BEDI T S, KANT R. Comparative performance of magnetorheological external finishing tools using different magnetic structures [J]. Materials Today: Proceedings, 2021, 41(Part 4): 908-914.

DENG Jiayun, LU Jiabin, ZENG Shuai, et al. Preparation and processing properties of magnetically controlled abrasive solidification orientation-solid-phase Fenton reaction lapping-polishing plate for single-crystal 4H-SiC [J]. Surfaces and Interfaces, 2022, 29: 101646.

YARALI E, ALI FARAJZADEH M, NOROOZI R, et al. Magnetorheological elastomer composites: modeling and dynamic finite element analysis [J]. Composite Structures, 2020, 254: 112881.

TSAI S W, WU E M. A general theory of strength for anisotropic materials. Journal of Composite Materials [J]. 1971, 5(1): 58-80.

陈家照, 黄闽翔, 王学仁, 等. 几种典型的橡胶材料本构模型及其适用性 [J]. 材料导报, 2015, 29: 118-120, 124.

CHEN Jiazhao, HUANG Minxiang, WANG Xueren, et al. Typical constitutive models of rubber materials and their ranges of application [J]. Materials Review, 2015, 29: 118-120, 124.

柳彬, 游世辉, 赵树勋, 等. 基于Digimat中RVE模型的磁流变弹性体的磁致压缩力学性能的数值模拟 [J]. 功能材料, 2018, 49(2): 2086-2092.

LIU Bin, YOU Shihui, ZHAO Shuxun, et al. Simulation of magnetic field induced compressive mechanical properties of magnetorheological elastomers based on RVE model in Digimat [J]. Journal of Functional Materials, 2018, 49(2): 2086-2092.

ASADI KHANOUKI M, SEDAGHATI R, HEMMATIAN M. Experimental characterization and microscale modeling of isotropic and anisotropic magnetorheological elastomers [J]. Composites Part B: Engineering, 2019, 176: 107311.

YAO Jianfei, YANG Wei, GAO Yu, et al. Magnetorheological elastomers with particle chain orientation: modelling and experiments [J]. Smart Materials and Structures, 2019, 28(9): 095008.

徐志强, 王秋良, 张高峰, 等. 可控柔性表面抛光研究综述 [J]. 表面技术, 2017, 46(10): 99-107.

XU Zhiqiang, WANG Qiuliang, ZHANG Gaofeng, et al. Controllable flexible surface polishing [J]. Surface Technology, 2017, 46(10): 99-107.

ZHU Wule, BEAUCAMP A. Compliant grinding and polishing: a review [J]. International Journal of Machine Tools and Manufacture, 2020, 158: 103634.

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Windage Loss and Flow Characteristics in Impeller Back Gaps of sCO2 Radial Inflow Turbines

Diffusion Characteristics and Influencing Factors in Case of Hydrogen Leakage from Fuel Cell Vehicles Running in Tunnels

Influence of Structural Parameters on the Summer Operational Characteristics of a Three-Tower-in-One Indirect Air-Cooling System

Turbulent Kinetic Energy Dissipation Mechanism of Supercritical Carbon Dioxide Leakage Flow in a Scallop Bionic Seal Cavity

Study on the Thermodynamic Properties in the Anomalous Region of Supercritical Water

Related Author

No data

Related Institution

No data

⁰