High Precision Motion Control Method for Hybrid Hydraulic Manipulator

LI Lin'an; CHENG Min; DING Ruqi; MA Jinhui

doi:10.7652/xjtuxb202306011

您当前的位置：

首页 >

文章列表页 >

High Precision Motion Control Method for Hybrid Hydraulic Manipulator

更新时间：2025-05-08

- High Precision Motion Control Method for Hybrid Hydraulic Manipulator
- Vol. 57, Issue 6, Pages: 95-104(2023)
- 作者机构：
  
  1. 重庆大学机械传动国家重点实验室,重庆,400044
  2. 华东交通大学载运工具与装备教育部重点实验室,南昌,330013
  3. 江苏八达重工机械股份有限公司,江苏,徐州,221400
- 作者简介：
- 基金信息：
- DOI：10.7652/xjtuxb202306011
  CLC： TP242
- Online First：10 June 2023，
  
  Published：2023
- 稿件说明：
移动端阅览
LI Lin'an, CHENG Min, DING Ruqi, et al. High Precision Motion Control Method for Hybrid Hydraulic Manipulator[J]. 2023, 57(6): 95-104.
DOI：

LI Lin'an, CHENG Min, DING Ruqi, et al. High Precision Motion Control Method for Hybrid Hydraulic Manipulator[J]. 2023, 57(6): 95-104. DOI： 10.7652/xjtuxb202306011.

摘要

针对串并混联液压臂中因结构耦合和系统非线性导致其末端位置控制精度差的问题

基于虚拟分解建模方法和液压系统控制理论

提出了一种混联液压臂的高精度运动控制方法。该方法通过对系统进行精确建模

消除了传统液压臂控制方法由于忽略结构耦合和系统非线性而引入的误差

从而提高了运动控制精度。首先

将混联液压臂复杂的串并联驱动结构分为摆动缸驱动的开链结构、活塞缸驱动的闭链结构和活塞缸驱动的并联结构3类

并根据3类结构的特征将机械臂进一步虚拟分割成简单的子系统; 然后

根据刚体动力学方程和流量连续方程分别建立了各子系统的动力学模型和液压执行器驱动模型

通过引入基于模型的前馈控制量和实时位置误差的反馈控制量设计了面向混联液压机械臂的高精度运动控制器。在七自由度混联液压机械臂试验平台上对该方法的有效性进行验证

结果表明:与传统PID控制器相比

采用该方法后液压臂末端在x和z方向的误差分别从59.63 mm和19.6 mm降低至11.17 mm和6.48 mm

仅为PID控制器的18.73%和33.06%

有效提高了混联液压机械臂的运动控制精度。

Abstract

To address the problem of low position control accuracy of the end-effector in a series-parallel hybrid hydraulic manipulator due to structural coupling and system nonlinearity

a high-precision motion control method for the hybrid hydraulic manipulator was proposed based on virtual decomposition modeling method and hydraulic system control theory. This method eliminated the errors introduced by traditional hydraulic manipulator control methods that ignore structural coupling and system nonlinearity by accurately modeling the system

thereby improving the motion control accuracy. Firstly

the complex series-parallel driving structure of the hybrid hydraulic manipulator was divided into three types: open-chain structure driven by swing cylinder

closed-chain structure driven by piston cylinder

and parallel structure driven by piston cylinder

and the manipulator was further virtually decomposed into simple subsystems based on the characteristics of these three types of structures. Then

dynamic models of each subsystem and drive models of the hydraulic actuator were established based on rigid body dynamics equations and flow continuity equations

and a high-precision motion controller for the hybrid hydraulic manipulator was designed by introducing model-based feedforward control and real-time position error feedback control. The effectiveness of this method was verified on a seven-degree-of-freedom hybrid hydraulic manipulator test platform. The results showed that compared with a traditional PID controller

the end-effector errors of the proposed method in x and z directions were reduced from 59.63 mm and 19.6 mm to 11.17 mm and 6.48 mm respectively

which were only 18.73% and 33.06% of a PID controller's error

effectively improving the motion control accuracy of the hybrid hydraulic manipulator.

关键词

Keywords

references

李运华, 范茹军, 杨丽曼, 等. 智能化挖掘机的研究现状与发展趋势 [J]. 机械工程学报, 2020, 56(13): 165-178.LI Yunhua, FAN Rujun, YANG Liman, et al. Research status and development trend of intelligent excavators [J]. Journal of Mechanical Engineering, 2020, 56(13): 165-178.[2] 梁涛, 张晓刚, 权龙, 等. 泵阀双源协同驱动多执行器系统特性研究 [J]. 西安交通大学学报, 2022, 56(3): 1-11.LIANG Tao, ZHANG Xiaogang, QUAN Long, et al. Characteristics of pump and valve dual-source collaborative driving multi-actuator system [J]. Journal of Xi'an Jiaotong University, 2022, 56(3): 1-11.[3] LI I H, CHIANG H H, LEE L W. Development of a linear delta robot with three horizontal-axial pneumatic actuators for 3-DOF trajectory tracking [J]. Applied Sciences, 2020, 10(10): 3526.[4] REGINALD N, SEO J, CHA M. Integrative tracking control strategy for robotic excavation [J]. International Journal of Control Automation and Systems, 2021, 19(10): 3435-3450.[5] DO T C, TRAN D T, DINH T Q, et al. Tracking control for an electro-hydraulic rotary actuator using fractional order fuzzy PID controller [J]. Electronics, 2020, 9(6): 926.[6] SUN Cong, CAO Liang. Research on trajectory tracking control of 7-DOF picking manipulator [J]. Science Progress, 2021, 104(1): 00368504211003383.[7] 潘昌忠, 费湘尹, 周兰, 等. 柔性关节机械臂的自适应命令滤波输出反馈控制 [J]. 西安交通大学学报, 2022, 56(5): 199-208.PAN Changzhong, FEI Xiangyin, ZHOU Lan, et al. Adaptive command filtered output feedback control for flexible joint manipulator [J]. Journal of Xi'an Jiaotong University, 2022, 56(5): 199-208.[8] KIM S W, CHO B, SHIN S, et al. Force control of a hydraulic actuator with a neural network inverse model [J]. IEEE Robotics and Automation Letters, 2021, 6(2): 2814-2821.[9] HOANG Q D, ROSAS-CERVANTES V A, LEE S G, et al. Robust finite-time convergence control mechanism for high-precision tracking in a hybrid fluid power actuator [J]. IEEE Access, 2020, 8: 196775-196789.[10] KADU C B, KOTHULE P S, VIKHE P S, et al. Design, analysis and motion control of hydraulic excavator using discrete sliding mode control with inertial delay [C]//2021 7th International Conference on Advanced Computing and Communication Systems(ICACCS). Piscataway, NJ, USA: IEEE, 2021: 255-260.[11] HELIAN Bobo, CHEN Zheng, YAO Bin. Energy-saving and accurate motion control of a hydraulic actuator with uncertain negative loads [J]. Chinese Journal of Aeronautics, 2021, 34(5): 253-264.[12] MOHANTY A, YAO Bin. Indirect adaptive robust control of hydraulic manipulators with accurate parameter estimates [J]. IEEE Transactions on Control Systems Technology, 2011, 19(3): 567-575.[13] 张蕾, 刘宇航, 王晓华, 等. 融合速度信息的机械臂自适应轨迹跟踪控制方法 [J]. 西安交通大学学报, 2022, 56(7): 47-55.ZHANG Lei, LIU Yuhang, WANG Xiaohua, et al. Adaptive trajectory tracking control of manipulator based on velocity information fusion [J]. Journal of Xi'an Jiaotong University,2022, 56(7): 47-55.[14] BOYER F, KHALIL W. An efficient calculation of flexible manipulator inverse dynamics [J]. The International Journal of Robotics Research, 1998, 17(3): 282-293.[15] ZHU Wenhong. Virtual decomposition control: toward hyper degrees of freedom robots [M]. Berlin, Germany: Springer, 2010.[16] ZHU Wenhong, PIEDBOEUF J C. Adaptive output force tracking control of hydraulic cylinders with applications to robot manipulators [J]. Journal of Dynamic Systems, Measurement, and Control, 2005, 127(2): 206-217.[17] KOIVUMÄKI J, ZHU Wenhong, MATTILA J. Addressing Closed-chain dynamics for high-precision control of hydraulic cylinder actuated manipulators [C]//BATH/ASME 2018 Symposium on Fluid Power and Motion Control. New York, NY, USA: ASME, 2018: V001T01A018.[18] KOIVUMÄKI J, MATTILA J. High performance nonlinear motion/force controller design for redundant hydraulic construction crane automation [J]. Automation in Construction, 2015, 51: 59-77.[19] 陈光荣, 王军政, 赵江波, 等. 基于虚拟分解控制的液压足式机器人单腿稳定阻抗控制 [J]. 机器人, 2017, 39(5): 704-714.CHEN Guangrong, WANG Junzheng, ZHAO Jiangbo, et al. Stable impedance control of a single leg of hydraulic legged robot based on virtual decomposition control [J]. Robot,2017, 39(5): 704-714.[20] 刘阳. 2-6UCU型串并联机构的虚拟分解控制 [D]. 哈尔滨:哈尔滨工业大学, 2019.[21] CHENG Min, HAN Zenan, DING Ruqi, et al. Development of a redundant anthropomorphic hydraulically actuated manipulator with a roll-pitch-yaw spherical wrist [J]. Frontiers of Mechanical Engineering, 2021, 16(4): 698-710.[22] CHENG Min, LI Linan, DING Ruqi, et al. Real-time anti-saturation flow optimization algorithm of the redundant hydraulic manipulator [J]. Actuators, 2021, 10(1): 11.

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Model-Based Balancing Method for High-Speed Machine Tool Spindle Without Trial Weights

Dynamic Balancing with Online Electromagnetic Balancing Device

Research on Inherent Characteristics and Sensitivities of Planetary Gear Transmission

A Simple Dynamic Model for Assessing the Forces on Ankle Joint under Different Loads and Different Gaits

Adaptive-Neural-Network-Based Terminal Sliding Mode Control for Six-Axis Robotic Manipulators

Related Author

许睦旬 1

姜歌东 1

邹冬林 1

梅雪松 1

章云 1

马石磊 1

张什永 3

Related Institution

School of Mechanical Engineering, Xi'an Jiaotong University

School of Mechanical Engineering, Xinjiang University

Department of Physical Education, Xi'an Jiaotong University

School of Mechanical Engineering, Shandong University

Key Laboratory of High-Efficiency and Clean Mechanical Manufacture of Ministry of Education, Shandong University

⁰