Tracking Error Control Strategy for Servo Feed System Connected with Series Axis

doi:10.7652/xjtuxb202105005

您当前的位置：

首页 >

文章列表页 >

Tracking Error Control Strategy for Servo Feed System Connected with Series Axis

更新时间：2025-07-09

- Tracking Error Control Strategy for Servo Feed System Connected with Series Axis
- Vol. 55, Issue 5, Pages: 34-44(2021)
- 作者机构：
  
  西安交通大学机械制造系统工程国家重点实验室,西安,710054
- 作者简介：
- 基金信息：
- DOI：10.7652/xjtuxb202105005
  CLC： TH16;TG659
- Online First：10 May 2021，
  
  Published：2021
- 稿件说明：
移动端阅览
Tracking Error Control Strategy for Servo Feed System Connected with Series Axis[J]. 2021, 55(5): 34-44.
DOI：

Tracking Error Control Strategy for Servo Feed System Connected with Series Axis[J]. 2021, 55(5): 34-44. DOI： 10.7652/xjtuxb202105005.

摘要

针对多轴数控机床中串联轴引入低阶模态

造成跟随误差难以控制的问题

提出一种模态滤波器与陷波滤波器的综合控制策略。首先通过建立具有串联轴滚珠丝杠伺服进给系统的动力学模型

分析串联轴引入的机械模态。其次

设计陷波滤波控制器与模态滤波控制器组合方案

对滚珠丝杠进给系统的高阶模态及串联轴引入的低阶模态进行抑制。最后

分析各个组合方案对伺服带宽及跟随误差的影响。结果表明:对于具有串联轴的滚珠丝杠伺服进给系统

由串联轴引起的低阶模态是限制位置环带宽提高的关键模态; 仅采用工程上常用的陷波滤波器对丝杠一阶、二阶扭转振动等高阶模态进行抑制

无法提高具有串联轴滚珠丝杠伺服进给系统的位置环带宽

也无法有效控制跟随误差; 对于具有串联轴的滚珠丝杠伺服进给系统

其跟随误差控制策略应为速度前馈控制器与低阶模态模态滤波器和高阶模态陷波滤波器的结合。

Abstract

Series axis of multi-axis CNC machine tool introduces low-order modes to result in a difficultly controlled tracking error. A comprehensive control strategy of modal filter and notch filter is proposed. Establishing a dynamic model of the ball-screw servo feed system with a series of shafts

the mechanical modes introduced by the series of shafts are analyzed. A combination scheme of notch filter controller with modal filter controller is designed to suppress the high-order modes of the ball-screw feed system and the low-order modes introduced by the series axis. The influence of each combination scheme on servo bandwidth and tracking error is discussed. It is concluded that for a ball-screw servo feed system with a series axis

the low-order modes caused by the series axis are the key modes that limit the increase in the bandwidth of the position loop; the notch filter commonly used in engineering suppresses high-order modes

such as the first-order and second-order torsional vibration of the screw

which cannot increase the bandwidth of the position loop of the ball-screw servo feed system with serial axis

and cannot effectively control the tracking error. For the ball-screw servo feed system with serial axis

the tracking error control strategy ought to choose as speed feedforward controller+low-order modal filter+high-order modal notch filter.

关键词

Keywords

references

赵万华, 张俊, 刘辉, 等. 数控机床精度评价新方法 [J]. 中国工程科学, 2013, 15(1): 93-98.

ZHAO Wanhua, ZHANG Jun, LIU Hui, et al. New evaluation method on the precision of NC machine tools [J]. Engineering Science, 2013, 15(1): 93-98.

TSAO T C, TOMIZUKA M. Zero phase error tracking algorithm for digital control [J].Journal of Dynamic Systems Measurement and Control, 1987, 10(4): 349.

RAHAMAN M, SEETHALER R, YELLOWLEY I. A new approach to contour error control in high speed machining [J]. International Journal of Machine Tools and Manufacture, 2015, 88: 42-50.

TOMIZUKA M. Zero phase error tracking algorithm for digital control [J]. IEE Conference Control Applications, 1987, 109(1): 65-68.

LI X, ZHANG J, ZHAO W, et al. A zero phase error tracking based path precompensation method for high-speed machining [J]. Proceedings of the Institution of Mechanical Engineers: Part C Journal of Mechanical Engineering Science, 2015, 230(2): 230-239.

陈兴林, 刘川, 周乃新, 等. 基于ZPETC-FF和DOB的精密运动平台控制 [J]. 哈尔滨工业大学学报, 2014, 46(1): 1-6.

CHEN Xinglin, LIU Chuan, ZHOU Naixin, et al. Controller design based on ZPETC-FF and DOB for precision motion platform [J]. Journal of Harbin Institute of Technology, 2014, 46(1): 1-6.

王丽梅, 李鑫. 直接驱动XY平台的零相位自适应鲁棒控制 [J]. 沈阳工业大学学报, 2014, 36(2): 121-126.

WANG Limei, LI Xin. Zero phase adaptive robust control of direct drive XY table [J]. Journal of Shenyang University of Technology, 2014, 36(2): 121-126.

TOMIZUKA M. Adaptive zero phase error tracking algorithm for digital control [J]. Journal of Dynamic Systems, Measurements, and Control, 1987, 109(1): 349-354.

TUNG E D, TOMIZUKA M, URUSHISAKI Y. High-speed end milling using a feedforward control architecture [J]. Journal of Manufacturing Science and Engineering, 1996, 118(2): 178-187.

TORFS D, SCHUTTER J D, SWEVERS J. Extended bandwidth zero phase error tracking control of nonminimal phase systems [J]. Journal of Dynamic Systems Measurement and Control, 1992, 114(3): 347-351.

BRAEMBUSSCHE P V D, SWEVERS J, BRUSSEL H V, et al. Accurate tracking control of linear synchronous motor machine tool axes [J]. Mechatronics, 1996, 6(5): 507-521.

SMITH D A. Wide bandwidth control of high-speed milling machine feed drives [D]. Gainesville, VA, USA: University of Florida, 1999: 55-66.

CHEN Yuche, TLUSTY J. Effect of low-friction guideways and lead-screw flexibility on dynamics of high-speed machines [J]. CIRP Annals: Manufacturing Technology, 1995, 44(1): 353-356.

KAMALZADEH A, ERKORKMAZ K. Compensation of axial vibrations in ball screw drives [J]. CIRP Annals: Manufacturing Technology, 2007, 56(1): 373-378.

ERKORKMAZ K, KAMALZADEH A. High bandwidth control of ball screw drives [J]. CIRP Annals: Manufacturing Technology, 2006, 55(1): 393-398.

YI C, YANG M, LANG Z, et al. Fast servo control and vibration suppression based on optical ZPETC and ZPNF [C]∥Proceedings of the 8th 2016 IEEE International Power Electronics and Motion Control Conference. Piscataway,NJ,USA: IEEE, 2016: 3654-3657.

ZHOU Y, PENG F, LI B. Adaptive notch filter control for the torsion vibration in lead-screw feed drive system based on neural network [C]∥Proceedings of the First International Conference on Intelligent Robotics and Applications. Berlin, Germany: Springer Verlag, 2008: 803-812.

KAMALZADEH A, ERKORKMAZ K. Accurate tracking controller design for high-speed drives [J]. International Journal of Machine Tools and Manufacture, 2007, 47(9): 1393-1400.

吕盾, 李润泽, 刘辉, 等. 数控机床高速高加速进给下的跟随误差控制策略 [J]. 西安交通大学学报, 2018, 52(12): 25-31.

LÜ Dun, LI Runze, LIU Hui, et al. A control strategy of tracking errors for numerical control machine tools at high speed and acceleration feeding [J]. Journal of Xi'an Jiaotong University, 2018, 52(12): 25-31.

吕盾, 张天宇, 郑贝贝, 等. 长传动链摆头主轴高加速度启停控制策略研究 [J]. 机械工程学报, 2019, 55(23): 210-215.

LÜ Dun, ZHANG Tianyu, ZHENG Beibei, et al. Control strategy of long-chain tilting head spindle for high-acceleration starts and stops [J]. Journal of Mechanical Engineering, 2019, 55(23): 210-215.

LIU Hui, ZHANG Jun, ZHAO Wanhua. An intelligent non-collocated control strategy for ball-screw feed drives with dynamic variations [J]. Engineering, 2017(5): 641-647.

ZHENG S, PRITSCHOW G, ZAHN P, et al. A novel cascade control principle for feed drives of machine tools [J]. CIRP Annals: Manufacturing Technology, 2018, 67(1): 389-392.

宋哲,杨军,梅雪松,等.永磁同步电机抗惯量扰动自适应速度控制.2020,54(12):14-21.[doi:10.7652/xjtuxb202012 002]

邓旭斌,姜歌东,孙铮,等.永磁同步电机的高带宽鲁棒容错电流预测控制.2020,54(10):84-93.[doi:10.7652/xjtuxb 202010010]

赵纯,于存贵,徐强,等.采用跃度模型和干扰估计的并联式加注机器人分散鲁棒控制.2019,53(3):164-174.[doi:10.7652/xjtuxb201903023]

成旭华,姚建勇,乐贵高.电液伺服系统多模型鲁棒自适应控制.2018,52(11):156-162.[doi:10.7652/xjtuxb201811023]

徐张宝,朱忠领,马大为,等.考虑状态约束的液压系统自适应控制.2017,51(1):97-108.[doi:10.7652/xjtuxb201701 015]

徐张宝,马大为,姚建勇,等.采用干扰估计的液压系统自适应鲁棒控制.2016,50(8):123-129.[doi:10.7652/xjtuxb2016 08020]

郝双晖,王磊,宋宝玉,等.交流伺服系统永磁同步电机电流及位置二级状态观测器设计.2015,49(5):100-115.[doi:10.7652/xjtuxb201505016]

俞珏,庄健,于德弘.采用李雅普诺夫函数的电液伺服系统反馈线性化控制.2014,48(7):71-76.[doi:10.7652/xjtuxb 201407013]

卢少武,唐小琦,周凤星,等.永磁同步直线伺服系统的纹波推力补偿.2014,48(2):106-110.[doi:10.7652/xjtuxb201402 018]

杨军,施虎,梅雪松,等.双驱伺服进给系统热误差的试验测量与预测模型构建.2013,47(11):53-59.[doi:10.7652/xjtuxb201311010]

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Contact Characters of Rolling Linear Guide Way Pair Under Heavy Load

Friction Compensation Strategy for Numerical Control Machine Tool by Reversing Character Analyzing

A Control Strategy of Tracking Errors for Numerical Control Machine Tools at High Speed and Acceleration Feeding

A Trajectory Error Prediction Method Considering Geometric Errors and Tracking Errors for Five-Axis Machine Tools

Research on the Electrohydrodynamic Effects of Ionic Liquid-Modified Fuels

Related Author

杜义贤

余媛

田红亮

任建功

冯斌

马振群

牟恩旭

刘辉

Related Institution

College of Mechanical and Power Engineering, China Three Gorges University

School of Mechanical Engineering, Xi'an Jiaotong University

⁰