Linear Motor Thrust Current Spectrum Characteristics Under Influence of Multi-Source Disturbance in Milling Process

doi:10.7652/xjtuxb202104002

您当前的位置：

首页 >

文章列表页 >

Linear Motor Thrust Current Spectrum Characteristics Under Influence of Multi-Source Disturbance in Milling Process

更新时间：2025-07-09

- Linear Motor Thrust Current Spectrum Characteristics Under Influence of Multi-Source Disturbance in Milling Process
- Vol. 55, Issue 4, Pages: 8-19(2021)
- 作者机构：
  
  1. 西安交通大学机械工程学院,西安,710049
  2. 西安交通大学机械制造系统工程国家重点实验室,西安,710049
- 作者简介：
- 基金信息：
- DOI：10.7652/xjtuxb202104002
  CLC： TG659
- Online First：10 April 2021，
  
  Published：2021
- 稿件说明：
移动端阅览
Linear Motor Thrust Current Spectrum Characteristics Under Influence of Multi-Source Disturbance in Milling Process[J]. 2021, 55(4): 8-19.
DOI：

Linear Motor Thrust Current Spectrum Characteristics Under Influence of Multi-Source Disturbance in Milling Process[J]. 2021, 55(4): 8-19. DOI： 10.7652/xjtuxb202104002.

摘要

针对机床实际铣削过程中进给系统受多源、多频扰动影响

特别是直驱进给系统由于“零传动”特性

运动精度受外界扰动影响更为显著的问题

研究了机床加工过程多源扰动机理、频谱特征及其影响下直线电机进给系统推力电流频谱特性

综合分析了铣削过程中刀具-主轴系统的多源扰动

建立了考虑刀具偏心跳动的铣削力模型、主轴离心力模型、主轴轴承振动模型

并分析多源扰动频谱特性。表征了多源扰动激励下直线电机进给系统输出位移波动特性

并在直线电机驱动的VMC0865机床上完成单轴进给切削实验。实验结果表明:在进给速度为1 500 mm/min、主轴转速为5 000 r/min、切宽为2 mm、切深为2 mm的情况下

X轴位移波动均方值从0.36 μm增加到0.81 μm

推力电流均方值从0.94 A增加到1.15 A; 推力电流增加了主轴转频及其倍频、分频、边频的谐波成分; 切削力会影响进给系统运动精度

从而影响零件加工质量和加工精度

验证了切削过程对直线电机进给系统推力电流频谱特征的影响; 对比了不同切削参数对进给系统推力电流频谱特征的影响

明确了主轴转速是对推力电流频谱特征最为显著的切削参数。该研究对于直驱进给系统控制算法改进与加工参数选择具有重要指导意义。

Abstract

The feed system is affected by multi-source and multi-frequency disturbances in the actual milling process of the machine tool

especially the direct-drive feed system due to the zero transmission

the motion accuracy is more significantly affected by external disturbances. The disturbance mechanism

frequency spectrum characteristics and linear motor feed system thrust current spectrum characteristics are investigated. Comprehensively considering the multi-source disturbance of tool-spindle system during the milling process

the milling force model

spindle centrifugal force model

spindle bearing vibration model are established and the corresponding multi-source disturbance spectrum characteristics are analyzed. The displacement fluctuation characteristics of linear motor feed system under multi-source disturbance excitation are characterized

and single-axis feed cutting experiment is completed on VMC0865 machine tool driven by a linear motor. The experimental results show that as the feed speed is 1 500 mm/min

spindle speed is 5 000 r/min

cutting width is 2 mm

and cutting depth is 2 mm

the mean square value of X-axis displacement fluctuation increases from 0.36 μm to 0.81 μm

and the mean square value of thrust current increases from 0.94 A to 1.15 A; the thrust current heightens the harmonic components of the spindle frequency and its multiplication

division and side frequencies; cutting force affects motion accuracy of the feed system

thereby lowers the quality and accuracy of the part processing. The influence of the process on the spectral characteristics of thrust current of linear motor feed system and the influence of different cutting parameters on the spectral characteristics of thrust current are comparatively analyzed. It is obvious that spindle speed is the most significant cutting parameter for spectral characteristics of thrust current.

关键词

Keywords

references

叶云岳. 直线电机在现代机床业中的应用与发展 [J]. 电机技术, 2010(3): 1-5.

YE Yunyue. Application & development of the linear motor in the modern machine tool industry [J]. Electrical Machinery Technology, 2010(3): 1-5.

中国机械工程学会. 中国机械工程技术路线图 [M]. 北京: 中国科学技术出版社, 2011: 10-15.

ALTINTAS Y, VERL A, BRECHER C, et al. Machine tool feed drives [J]. CIRP Annals, 2011, 60(2): 779-796.

PAN Zhenbao, DONG Fei, ZHAO Jiwen, et al. Combined resonant controller and two-degree-of-freedom PID controller for PMSLM current harmonics suppression [J]. IEEE Transactions on Industrial Electronics, 2018, 65(9): 7558-7568.

CHEN Yuanrui, WU Jie, CHEUNG N C. Lyapunov's stability theory-based model reference adaptive control for permanent magnet linear motor drives [C]∥First International Conference on Power Electronics Systems and Application. Piscataway, NJ, USA: IEEE, 2004: 260-265.

CAO Rongmin, HOU Zhongsheng, ZHAO Yunjie, et al. Model free adaptive iterative learning control for tool feed system in noncircular turning [J]. IEEE Access, 2019, 7: 113712-113725.

ALTER D M, TSAO T C. Control of linear motors for machine tool feed drives: design and implementation of H∞optimal feedback control [J]. Journal of Dynamic Systems, Measurement, and Control, 1996, 118(4): 649-656.

CHOI C, TSAO T C. Control of linear motor machine tool feed drives for end milling: robust MIMO approach [J]. Mechatronics, 2005, 15(10): 1207-1224.

XU Li, YAO Bin. Adaptive robust precision motion control of linear motors with negligible electrical dynamics: theory and experiments [J]. ASME Transactions on Mechatronics, 2001, 6(4): 444-452.

JAMALUDIN Z, VAN BRUSSEL H, PIPELEERS G, et al. Accurate motion control of xy high-speed linear drives using friction model feedforward and cutting forces estimation [J]. CIRP Annals, 2008, 57(1): 403-406.

ALTINTAS Y, OKWUDIRE C E. Dynamic stiffness enhancement of direct-driven machine tools using sliding mode control with disturbance recovery [J]. CIRP Annals, 2009, 58(1): 335-338.

OHNISHI K. New development of servo technology in mechatronics [J]. IEEJ Transactions on Industry Applications, 1987, 107(1): 83-86.

YANG Jun, CHEN Wenhua, LI Shihua, et al. Disturbance/uncertainty estimation and attenuation techniques in PMSM drives: a survey [J]. IEEE Transac-tions on Industrial Electronics, 2017, 64(4): 3273-3285.

TAKEI M, KURIHARA D. Hybrid control for machine tool table applying sensorless cutting force monitoring [J]. International Journal of Automation Technology, 2011, 5(4): 587-593.

ALTINTAS Y. Manufacturing automation: metal cutting mechanics, machine tool vibrations, and CNC design [M]. Cambridge, UK: Cambridge University Press, 2012: B84.

杨蕊. 滚动轴承振动特性分析与微弱故障诊断方法研究 [D]. 大连: 大连理工大学, 2019: 20-30.

赵联春. 球轴承振动的研究 [D]. 杭州: 浙江大学, 2003: 56-79.

SCHMITZ T L, SMITH K S. Turning dynamics [M]∥ Machining Dynamics. Boston, MA: Springer US, 2009: 275-280.

谢国芳. 一般三次方程的简明新求根公式和根的判别法则 [J]. 数学学习与研究(教研版), 2012(21): 125-128.

XIE Guofang. The concise new root-finding formula and root-discriminating rule of general cubic equation [J]. Mathematics Learning and Research, 2012(21): 125-128.

杨晓君. 永磁同步直线电机进给系统运动平稳性分析与优化 [D]. 西安: 西安交通大学, 2017: 45-60.

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Study on Self-Sensing Technique of Linear Refrigerator Compressor's Piston Displacement

Design of Magnet Arrays for a Permanent Magnetic Linear Motor

Effect of Linear Motor Parameters on Output of Piston Displacement Self-Sensor

Stick-Slip Experimental Method Based on Closed Loop Positioning System

Dynamic Characteristics of Mechanical System in Linear Motor Feed System

Related Author

郭福田 2

牛元君 2

畅云峰 1

张金权 1

谢友柏

姜强

罗俊航

毛军红

Related Institution

School of Energy and Power Engineering, Xi'an Jiaotong University

School of Mechanical Engineering, Xi'an Jiaotong University

西安交通大学润滑理论与轴承研究所

State Key Laboratory for Manufacturing Systems Engineering, Xi'an Jiaotong University

Beijing Institute of Petrochemical Technology

⁰