Design and Analysis of Compensation Modification for Multi-Pair Contact of High-Contact-Ratio Helical Gears

doi:10.7652/xjtuxb202011007

您当前的位置：

首页 >

文章列表页 >

Design and Analysis of Compensation Modification for Multi-Pair Contact of High-Contact-Ratio Helical Gears

更新时间：2025-07-09

- Design and Analysis of Compensation Modification for Multi-Pair Contact of High-Contact-Ratio Helical Gears
- Vol. 54, Issue 11, Pages: 56-64(2020)
- 作者机构：
  
  西北工业大学机电学院,西安,710072
- 作者简介：
- 基金信息：
- DOI：10.7652/xjtuxb202011007
  CLC： TH132
- Online First：10 November 2020，
  
  Published：2020
- 稿件说明：
移动端阅览
Design and Analysis of Compensation Modification for Multi-Pair Contact of High-Contact-Ratio Helical Gears[J]. 2020, 54(11): 56-64.
DOI：

Design and Analysis of Compensation Modification for Multi-Pair Contact of High-Contact-Ratio Helical Gears[J]. 2020, 54(11): 56-64. DOI： 10.7652/xjtuxb202011007.

摘要

为准确计算齿面修形量以降低承载传动误差波动幅值

考虑齿轮传动过程中不同啮合区之间轮齿承载变形的变化规律

提出了高重合度斜齿轮多齿对啮合的补偿修形设计方法。基于标准齿面在设计载荷下的承载传动误差波动幅值大小和方向

预设修形齿面的几何传动误差; 通过优化几何传动误差控制齿面修形量大小

实现轮齿不同啮合区的精确补偿修形; 建立齿向改进修形齿面模型

以齿条刀具附加转角和齿向修形参数为优化变量

采用快速非支配排序遗传算法(NSGA-II)基于承载传动误差幅值最小确定齿面最佳修形量。研究结果表明:啮合齿对变化引起不同啮合区之间轮齿承载变形的变化是承载传动误差幅值波动的主要原因; 齿面补偿修形后

承载传动误差幅值大幅下降

在设计负载下

承载传动误差幅值几乎降到零; 改进修形也能够有效补偿不同啮合区之间轮齿承载变形的差异

同时避免了边缘接触

降低了齿轮副的振动与噪声。

Abstract

To accurately calculate the amount of the tooth surface modification to reduce the amplitude of load transmission error(ALTE)

considering the load-bearing deformation of the teeth between different meshing areas in the process of gear meshing

a design method of compensation modification for multi-pair contact of high contact ratio helical gears is proposed. The transmission error of modified tooth surface is predesigned based on the magnitude and direction of ALTE of the standard tooth surface under the design load

and the precise compensation modification in different meshing areas of the tooth is realized by optimizing the TE to control the value of the tooth surface modification. The model of a further longitudinal modified tooth surface is established

and the additional angle of rack cutters and the parameters of the longitudinal correction are taken as the optimization variables. The optimal tooth surface modification values are determined by the fast elitist non-dominated sorting genetic algorithm(NSGA-II)based on the minimum ALTE. The results show that the change of load-bearing deformation caused by the change of meshing pairs is the main cause for the fluctuation of the ALTE. After the tooth surface compensation modification

the ALTE decreases greatly

and under the designed load

the ALTE drops to almost zero. The further longitudinal correction can also effectively compensate the difference of tooth deformation between different meshing areas of the teeth

avoiding the edge contact

and reducing the vibration and noise of gears.

关键词

Keywords

references

张俊, 陈涛, 汪建. 基于最小动态传动误差波动量的斜齿行星轮系齿轮修形研究 [J]. 振动与冲击, 2019, 38(19): 77-88.

ZHANG Jun, CHEN Tao, WANG Jian. Tooth modification of helical planetary gear train based on minimum dynamic transmission error fluctuation [J]. Journal of Vibration and Shock, 2019, 38(19): 77-88.

王晋鹏, 常山, 刘更, 等. 船舶齿轮传动装置箱体振动噪声分析与控制研究进展 [J]. 船舶力学, 2019, 23(8): 1007-1019.

WANG Jinpeng, CHAN Shan, LIU Geng, et al. Review on the analysis and reduction of marine gearbox vibration and noise [J]. Journal of Ship Mechanics, 2019, 23(8): 1007-1019.

KANG M R, KAHRAMAN A. Measurement of vibratory motions of gears supported by compliant shafts [J]. Mechanical Systems and Signal Processing, 2012, 29: 391-403.

KANG M R, KAHRAMAN A. An experimental and theoretical study of the dynamic behavior of double-helical gear sets [J]. Journal of Sound and Vibration, 2015, 350: 11-29.

周建星, 孙文磊, 万晓静. 齿轮减速器振动噪声预估公式定制方法研究 [J]. 振动与冲击, 2014, 33(7): 174-180.

ZHOU Jianxing, SUN Weilei, WAN Xiaojing. Fornual-fitting method for predicting gear reducer noise radiation [J]. Journal of Vibration and Shock, 2014, 33(7): 174-180.

LITVIN F L, GONZALEZ P I, FUENTES A, et al. Topology of modified surfaces of involute helical gears with line contact developed for improvement of bearing contact, reduction of transmission errors, and stress analysis [J]. Mathematical and Computer Modelling, 2005, 42(9): 1063-1078.

LITVIN F L. Modified involute helical gears computerized design, simulation of meshing and stress analysis [J]. Computer Methods in Applied Mechanics and Engineering, 2003, 192: 3619-3655.

方宗德, 沈允文. 斜齿轮三维修形的优化设计 [J]. 机械工程学报, 1992, 28(6): 57-61.

FANG Zongde, SHEN Yunwen. Optimal design of 3D modification of helical gears [J]. Journal of Mechanical Engineering, 1992, 28(6): 57-61.

汪建, 张俊. 轮齿修形对斜齿轮传递误差影响的比较性分析 [J]. 振动与冲击, 2018, 37(2): 254-260.

WANG Jian, ZHANG Jun. Effect of gear modification on transmission error of a helical gear pair [J]. Journal of Vibration and Shock, 2018, 37(2): 254-260.

陈洪月, 朱煜, 毛君, 等. 齿廓修形对渐开线直齿轮设计传递误差的影响 [J]. 华中科技大学学报(自然科学版), 2018, 46(3): 91-97.

CHEN Hongyue, ZHU Yu, MAO Jun, et al. Influence of tooth profile modification on design transmission error of involute spur gear [J]. Journal of Huazhong University of Science and Technology(Natural Science Edition), 2018, 46(3): 91-97.

贾超, 方宗德, 张西金, 等. 斜齿轮齿面的修形优化设计及分析 [J]. 华中科技大学学报(自然科学版), 2018, 46(5): 66-71.

JIA Chao, FANG Zongde, ZHANG Xijin, et al. Optimal design and analysis of tooth modification for helical gears [J]. Journal of Huazhong University of Science and Technology(Natural Science Edition), 2018, 46(5): 66-71.

王宪法, 李华敏. 窄斜齿轮对角修形的最佳修形量计算及修形区域的选择 [J]. 哈尔滨工业大学学报, 1993(5): 67-71.

WANG Xianfa, LI Huamin. The calculation of optimal diagonal modification values and selection of modification area of the narrow helical gears [J]. Journal of Harbin Institute of Technology, 1993(5): 67-71.

蒋进科, 方宗德, 王峰. 降低斜齿轮噪声的对角修形优化设计 [J]. 振动与冲击, 2014, 33(7): 63-67.

JIANG Jinke, FANG Zongde, WANG Feng. Optimal design with diagonal modification for reducing helical gear noise [J]. Journal of Vibration and Shock, 2014, 33(7): 63-67.

袁冰, 常山, 吴立言, 等. 对角修形对斜齿轮系统准静态及动态特性的影响研究 [J]. 西北工业大学学报, 2017, 35(2): 232-239.

YUAN Bing, CHANG Shan, WU Liyan, et al. Effect of cross modification on the quasi-static and dynamic characteristics of helical gear system [J]. Journal of Northwester Polytechnical University, 2017, 35(2): 232-239.

LEE C K. Manufacturing process for a cylindrical crown gear drive with a controllable fourth order polynomial function of transmission errors [J]. Journal of Mater Process Technology, 2009, 209(1): 3-13.

蒋进科, 方宗德, 苏进展. 高阶传动误差斜齿轮修形设计与加工 [J], 哈尔滨工业大学学报, 2014, 46(9): 43-49.

JIANG Jinke, FANG Zongde, SU Jinzhan. Design and grinding for modified helical gears with a higher-order transmission error [J]. Journal of Harbin Institute of Technology, 2014, 46(9): 43-49.

JIANG Jinke, FANG Zongde. Design and analysis of modified cylindrical gears with a higher-order transmission error [J]. Mechanism and Machine Theory, 2015, 88: 141-152.

ZHANG Yi, FANG Zongde. Analysis of transmission errors under load of helical gears with modified tooth surfaces [J]. Journal of Mechanical Design, 1997, 119(1): 120-126.

方宗德. 齿轮轮齿承载接触分析(LTCA)的模型和方法 [J]. 机械传动, 1998, 22(2): 1-3.

FANG Zongde. Model and method of loaded tooth contact analysis(LTCA)[J]. Journal of Mechanical, 1998, 22(2): 1-3.

DEB K, MEMBER A, PRATAP A, et al. A fast and elitist multiobjective genetic algorithm: NSGA-II [J]. Transaction on Evolutionary Computation, 2002, 6(2): 182-197.

贾超,姚立纲,张俊,等.修形渐开线斜齿轮啮入冲击计算.2020,54(9):58-65.[doi:10.7652/xjtuxb202009006]

李旺,赵宁,蔺彦虎,等.同轴面齿轮分扭传动的动态均载特性.2020,54(9):109-116.[doi:10.7652/xjtuxb202009012]

王胜男,阿达依·谢尔亚孜旦,章翔峰,等.考虑轴柔性的二级齿轮减速器振动噪声研究.2020,54(9):117-127.[doi:10.7652/xjtuxb202009013]

蒋进科,刘钊,刘红梅.齿面磨损最小直齿锥齿轮Ease-off修形设计与分析.2020,54(6):99-106.[doi:10.7652/xjtuxb 202006013]

王成龙,周建星,孙文磊,等.行星齿轮传动柔性齿圈齿根动应力计算及光纤光栅检测方法.2020,54(6):122-132.[doi:10.7652/xjtuxb202006016]

王靖岳,李建刚,王浩天.采用改进多点最优最小熵反褶积的齿轮箱复合故障特征提取.2020,54(5):70-77.[doi:10.7652/xjtuxb202005010]

姚斌,卢杰,蔡志钦,等.螺杆转子成形磨削用砂轮廓形的包络-像素设计方法.2020,54(2):16-23.[doi:10.7652/xjtuxb 202002003]

陈保家,黄伟,李立军,等.最大重叠离散小波包变换边际谱特征在齿轮故障诊断中的应用.2020,54(2):35-42.[doi:10.7652/xjtuxb202002005]

刘振,孔德同,赵明,等.裂纹损伤行星轮系的编码器信号响应特性.2020,54(2):43-50.[doi:10.7652/xjtuxb202002006]

吴静然,丁恩杰,崔冉,等.采用多尺度注意力机制的旋转机械故障诊断方法.2020,54(2):51-58.[doi:10.7652/xjtuxb 202002007]

张西宁,周融通,郭清林,等.局部倒频谱编辑方法及其在齿轮箱微弱轴承故障特征提取中的应用.2019,53(12):1-9.[doi:10.7652/xjtuxb201912001]

张宁,张英杰,李阳帆.考虑齿轮形变的谐波减速器齿廓优化方法.2019,53(12):31-37.[doi:10.7652/xjtuxb201912005]

姜歌东,王爽,梅雪松,等.谐波齿轮传动双圆弧齿形双向共轭设计方法.2019,53(8):8-14.[doi:10.7652/xjtuxb2019 08002]

胡升阳,方宗德.行星传动均载及动载系数定义改进与分析.2019,53(8):40-46.[doi:10.7652/xjtuxb201908006]

何小高,张庆,贾林山,等.变速重载设备齿轮箱轴承故障的改进阶次包络分析方法.2019,53(8):98-106.[doi:10.7652/xjtuxb201908013]

彭山东,丁撼,唐进元.改进的6σ设计的螺旋锥齿轮加工参数反调修正方法.2019,53(6):35-43.[doi:10.7652/xjtuxb 201906006]

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Knowledge Graph Representation Learning Driven by Semantic Discrimination and Subgraph Integration

A Structure-Semantics-Residual Collaborative Image Compression Framework：Towards Privacy Protection and High-Fidelity Reconstruction

A Fast Calculation Method for Thermal Flow Fields in Transformer Windings Based on PI-DeepONet

Effects of Expansion Angle Crater Film Hole on the Film Cooling Characteristics of a Double-Wall Structure

Influence of Structural Parameters on the Summer Operational Characteristics of a Three-Tower-in-One Indirect Air-Cooling System

Related Author

No data

Related Institution

No data

⁰