Analysis for Effects of Drying Temperature on Web Tension in Gravure Printing Machine

doi:10.7652/xjtuxb201812021

您当前的位置：

首页 >

文章列表页 >

Analysis for Effects of Drying Temperature on Web Tension in Gravure Printing Machine

更新时间：2025-05-08

- Analysis for Effects of Drying Temperature on Web Tension in Gravure Printing Machine
- Vol. 52, Issue 12, Pages: 145-151(2018)
- 作者机构：
  
  1. 西安交通大学机械工程学院,西安,710049
  2. 河南科技大学机电工程学院,河南,洛阳,471003
- 作者简介：
- 基金信息：
- DOI：10.7652/xjtuxb201812021
  CLC： TS835
- Online First：10 December 2018，
  
  Published：2018
- 稿件说明：
移动端阅览
Analysis for Effects of Drying Temperature on Web Tension in Gravure Printing Machine[J]. 2018, 52(12): 145-151.
DOI：

Analysis for Effects of Drying Temperature on Web Tension in Gravure Printing Machine[J]. 2018, 52(12): 145-151. DOI： 10.7652/xjtuxb201812021.

摘要

为了提高凹版印刷中料带张力的控制精度

需要对凹版印刷中的张力模型进行深入研究

建立更加精确的张力模型

重点研究电子轴凹版印刷烘干温度对印刷部分张力系统的影响。首先根据质量守恒定律建立了包含温度因素的印刷部分张力模型

该数学模型首次考虑了干燥系统造成的料带温度不均匀分布状态; 然后从系统输入和输出关系出发

采用MATLAB/Simulink软件对张力模型进行数值仿真

并在电子轴凹版印刷设备上进行实验研究

验证张力模型和数值仿真的正确性; 最后分析了烘干温度对张力系统特性的影响规律。研究表明:烘干温度对张力系统稳态性能没有影响

而对系统的瞬态特性影响显著

瞬态过渡过程时间随着烘干温度增高而增长; 在电子轴凹版印刷机工作条件下

烘干温度为60～80 ℃时

瞬态过渡过程时间相比于无干燥系统增长了41%～82%。该研究成果为电子轴凹版印刷张力系统和套准系统的理论研究提供了重要基础

有利于提高电子轴凹版印刷产品质量。

Abstract

To improve the control accuracy of web tension in gravure printing

it is necessary to construct a more accurate mathematical tension model

where the effects of the drying temperature on web tension in shaft-less drive gravure printing process are considered. The tension model of printing section including temperature is derived following the law of mass conservation

in which the non-uniform distribution of the web temperature caused by the drying system is considered. Then

simulations with MATLAB/Simulink and experiments are carried out

and the effects of the drying temperature on the characteristics of web tension are obtained. The results show that the drying temperature exerts significant influences on transient web tension in printing section rather than on steady responses. In the transient responses

the settling time increases with the rising drying temperature. As the drying temperature is 60-80 ℃

the settling time in transient responses is about 41%-82% more than that without drying system under normal working condition.

关键词

Keywords

references

LI Jian, MEI Xuesong, TAO Tao, et al. Design tension controller of unwinding system based on BP neural network [J]. Advanced Science Letters, 2011, 4(6/7): 2222-2226.

李健, 梅雪松, 陶涛, 等. 放卷张力系统H∞鲁棒控制器的设计 [J]. 西安交通大学学报, 2012, 46(1): 86-90.

LI Jian, MEI Xuesong, TAO Tao, et al. H∞robust control design for unwinding tension system [J]. Journal of Xi'an Jiaotong University, 2012, 46(1): 86-90.

刘善慧, 梅雪松, 杜喆, 等. 放卷张力系统解耦控制器的设计 [J]. 西安交通大学学报, 2012, 46(9): 55-59.

LIU Shanhui, MEI Xuesong, DU Zhe, et al. Decoupling controller design for unwinding tension system [J]. Journal of Xi'an Jiaotong University, 2012, 46(9): 55-59.

LIU Shanhui, MEI Xuesong, KONG Fanfeng, et al. A decoupling control algorithm for unwinding tension system based on active disturbance rejection control [J]. Mathematical Problems in Engineering, 2013(6): 1798-1803.

GASSMANN V, KNITTEL D, PAGILLA P R, et al. Fixed-order H∞tension control in the unwinding section of a web handling system using a pendulum dancer [J]. IEEE Transactions on Control Systems Technology, 2011, 20(1): 173-180.

YANG Mei, ZHANG Shaoru. The research of tension control system in web press based on the fuzzy adaptive PID controller [C]∥Proceedings of the 2014 9th IEEE Conference on Industrial Electronics and Applications. Piscataway, NJ, USA: IEEE, 2014: 1204-1208.

PARK J C, JEON S W, NAM K S, et al. Tension control of web of winder span using adaptive gain control method [J]. Japanese Journal of Applied Physics, 2014, 53(5S3): 05HC11.

ABJADI N R, SOLTANI J, ASKARI J, et al. Nonlinear sliding-mode control of a multi-motor web-winding system without tension sensor [J]. IET Control Theory Applications, 2009, 3(4): 419-427.

周春雷, 陈建魁, 尹周平. 薄膜非连续开卷张力控制建模、仿真与实验 [J]. 电气自动化, 2013, 35(3): 9-11.

ZHOU Chunlei, CHEN Jiankui, YIN Zhouping. Modeling, simulation and experiment of tension control in film non-continuous unwinding system [J]. Electrical Automation, 2013, 35(3): 9-11.

张永芳, 畅亚利, 高阳阳, 等. 模糊自抗扰控制在凹印机放卷张力中的应用 [J]. 西安理工大学学报, 2015, 31(2): 144-149.

ZHANG Yongfang, CHANG Yali, GAO Yangyang, et al. Fuzzy ADRC applied in gravure press tension control system [J]. Journal of Xi'an University of Technology, 2015, 31(2): 144-149.

SHAO Mingyue, WU Jimei, WANG Yan, et al, Research on modeling method of winding tension system for gravure printing machine [C]∥Proceedings of the 2016 Symposium on Piezoelectricity, Acoustic Waves, and Device Applications. Piscataway, NJ, USA: IEEE, 2016: 110-114.

MARTZ Y, BA A, KNITTEL D. Robust industrial control with optimized decoupling in roll-to-roll systems: new approaches using finite element modeling of the Web [C]∥IEEE International Conference on Emerging Technologies Factory Automation. Piscataway, NJ, USA: IEEE, 2015: 7301642.

MARTZ Y, KNITTEL D. Robust control in industrial roll-to-roll systems: new approaches using finite element modeling of the web [C]∥IEEE International Conference on Industrial Technology. Piscataway, NJ, USA: IEEE, 2015: 464-469.

TRAN T T, CHOI K H. A backstepping-based control algorithm for multi-span roll-to-roll web system [J]. International Journal of Advanced Manufacturing Technology, 2014, 70(1/2/3/4): 45-61.

CHEN Zhihua, HE Juanjuan, ZHENG Ying, et al. An optimized feedforward decoupling PD register control method of roll-to-roll web printing systems [J]. IEEE Transactions on Automation Science Engineering, 2016, 13(1): 274-283.

CHEN Zhihua, ZHENG Ying, ZHOU Minjing, et al. Model-based feedforward register control of roll-to-roll web printing systems [J]. Control Engineering Practice, 2016, 51: 58-68.

LIU Shanhui, MEI Xuesong, LI Jian, et al. Machine directional register system modeling for shaft-less drive gravure printing machines [J]. Mathematical Problems in Engineering, 2013, 2013(2): 206-226.

刘善慧, 梅雪松, 李健, 等. 多色套准系统前馈自抗扰控制器设计 [J]. 机械工程学报, 2015, 51(5): 143-150.

LIU Shanghui, MEI Xuesong, LI Jian, et al. Design feedforward active disturbance rejection control controller for multi-color register system [J]. Journal of Mechanical Engineering, 2015, 51(5): 143-150.

刘成, 吕延军, 张永芳, 等. 无轴传动凹版印刷机的相邻偏差耦合同步控制 [J]. 振动. 测试与诊断, 2017, 37(6): 1242-1249.

LIU Cheng, LÜ Yanjun, ZHAN Yongfang, et al. Adjacent error-coupling strategy for synchronization control of shaftless driven gravure printing machine [J]. Journal of Vibration, Measurement diagnosis, 2017, 37(6): 1242-1249.

TORRES E O C, PAGILLA P R. Temperature distribution in moving webs heated by radiation panels: model development and experimental validation [J]. Journal of Dynamic Systems Measurement Control, 2017, 139(5): 1-8.

TORRES E O C, PAGILLA P R. A governing equation for moving web temperature heated by radiative panels [C]∥Proceedings of the American Control Conference. Piscataway, NJ, USA: IEEE, 2016: 858-863.

HE Kui, WANG Kedian, ZHANG Dongsheng, et al. Modeling and analysis of web tension between two adjacent printing rollers in shaft-less drive gravure printing systems [C]∥Proceedings of 2017 IEEE 2nd Advanced Information Technology, Electronic and Automation Control Conference. Piscataway, NJ, USA: IEEE, 2017: 1761-1766.

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Numerical Simulation of Heat-Moisture Barrier Performance of a Horizontal Air Curtain in Cold Storage

Knowledge Graph Representation Learning Driven by Semantic Discrimination and Subgraph Integration

Sensitivity Analysis of Foil Geometrical Parameters for the Third-Generation CO2 Gas Foil Bearings Based on Design of Experiments Method

Energy Efficiency Optimization of the Cryogenic Air Separation Process for Electronic-Grade Ultra Pure Nitrogen

Study on the Thermodynamic Properties in the Anomalous Region of Supercritical Water

Related Author

No data

Related Institution

No data

⁰