Effects of Ti(C,N)Content on Mechanical Properties of Ti(C,N)-304 Stainless Steel Cermet

doi:10.7652/xjtuxb201810022

您当前的位置：

首页 >

文章列表页 >

Effects of Ti(C,N)Content on Mechanical Properties of Ti(C,N)-304 Stainless Steel Cermet

更新时间：2025-07-09

- Effects of Ti(C,N)Content on Mechanical Properties of Ti(C,N)-304 Stainless Steel Cermet
- Vol. 52, Issue 10, Pages: 159-166(2018)
- 作者机构：
  
  1. 西安交通大学金属材料强度国家重点实验室,西安,710049
  2. 西安交通大学铸造及耐磨材料研究所,西安,710049
- 作者简介：
- 基金信息：
- DOI：10.7652/xjtuxb201810022
  CLC： TF124
- Online First：10 October 2018，
  
  Published：2018
- 稿件说明：
移动端阅览
Effects of Ti(C,N)Content on Mechanical Properties of Ti(C,N)-304 Stainless Steel Cermet[J]. 2018, 52(10): 159-166.
DOI：

Effects of Ti(C,N)Content on Mechanical Properties of Ti(C,N)-304 Stainless Steel Cermet[J]. 2018, 52(10): 159-166. DOI： 10.7652/xjtuxb201810022.

摘要

采用传统粉末冶金的方法研究了Ti(C

N)硬质相含量对Ti(C

N)-304不锈钢金属陶瓷的微观组织和力学性能的影响。通过扫描电子显微镜和透射电子显微镜观测了不同硬质相含量的金属陶瓷的微观组织、断口形貌、裂纹传播规律以及晶界微裂纹的产生

并基于体视学原理分析了硬质相邻接度和粘结相平均自由程。使用阿基米德排水法、洛氏硬度计和三点弯曲法分别测量了金属陶瓷的致密度、硬度和抗弯强度

结果表明:随着硬质相含量的增加

金属陶瓷硬质相平均颗粒直径先减小后增大

在硬质相体积分数为75%时

达到最大致密度(98.4%)、硬度(HRA 89.2)和抗弯强度(1 291 MPa); 在裂纹传播过程中

以沿晶断裂为主

穿晶断裂为辅; 大颗粒更容易发生穿晶断裂

且由于大颗粒存在尖角

容易导致应力集中形成微裂纹

不利于材料力学性能的提高。

Abstract

The effects of Ti(C

N)content on microstructure and mechanical properties of Ti(C

N)-304 stainless steel cermet are analyzed. Scanning electron microscopy and transmission electron microscopy are adopted to observe the microstructures

fracture morphology

crack propagation and microcrack in the cermet with different hard phase content. The contiguity of the hard phase and the binder mean free path are discussed following the stereological principle. The relative density

hardness and transverse rupture strength of the cermet are measured with Archimedes principle

Rockwell hardness tester and three-point-bending method

respectively. With the increasing hard phase content

the average particle diameter of the hard phase firstly decreases and then increases. When the hard phase content is 75%

the cermet obtains the maximum relative density(98.4%)

maximum hardness(HRA 89.2)and maximum transverse rupture strength(1 291 MPa). In the process of crack propagation

intergranular fracture and transgranular fracture simultaneously appear

but the former is in majority. Large Ti(C

N)grains are more prone to appear transgranular fracture. The stress concentration due to sharp corners of large particles leads to microcrack

which is not conducive to improve the mechanical properties of the material.

关键词

Keywords

references

ONUOHA C C, JIN C, FARHAT Z N, et al. The effects of TiC grain size and steel binder content on the reciprocating wear behaviour of TiC-316L stainless steel cermets [J]. Wear, 2016, 350: 116-129.

HE L, GAO Y, LI Y, et al. Effect of milling time on the microstructure and mechanical properties of Ti(C,N)-304 stainless steel cermet [J]. Materials Research Express, 2018, 5(2): 1-10.

望军, 刘颖, 叶金文, 等. Ti(C,N)基金属陶瓷抗弯强度的研究 [J]. 硬质合金, 2008, 25(3): 140-142.

WANG Jun, LIU Ying, YE Jinwen, et al. Investigate the transverse rupture strength of Ti(C,N)based cermets [J]. Cemented Carbide, 2008, 25(3): 140-142.

康新婷, 刘素英, 蒋纪麟. Ti(C,N)基金属陶瓷的制备与应用 [J]. 硬质合金, 1999, 16(1): 51-55.

KANG Xinting, LIU Suying, JIANG Jilin. The fabricate and application of Ti(C,N)based cermets [J]. Cemented Carbide, 1999, 16(1): 51-55.

熊继, 张亚昆, 沈保罗, 等. 超细TiCN金属陶瓷的制备及性能 [J]. 粉末冶金技术, 2003, 21(2): 92-95.

XIONG Ji, ZHANG Yakun, SHEN Baoluo, et. al. Fabricate and mechanical properties of super-fine Ti(C,N)based cermets [J]. Powder Metallurgy Technology, 2003, 21(2): 92-95.

CHEN M, ZHUANG Q, LIN N, et al. Improvement in microstructure and mechanical properties of Ti(C,N)-Fe cermets with the carbon additions [J]. Journal of Alloys and Compounds, 2017, 701: 408-415.

GORDO E, GÓMEZ B, RUIZ-NAVAS E M, et al. Influence of milling parameters on the manufacturing of Fe-TiCN composite powders [J]. Journal of Materials Processing Technology, 2005, 162(10): 59-64.

JIN C, PLUCKNETT K P. Microstructure instability in TiC-316L stainless steel cermets [J]. International Journal of Refractory Metals and Hard Materials, 2016, 58: 74-83.

JIN C, ONUOHA C C, FARHAT Z N, et al. Reciprocating wear behaviour of TiC-stainless steel cermets [J]. Tribology International, 2017, 105: 250-263.

SHEN Y, HUANG Z, ZHANG L. Effect of milling time on the microstructure and mechanical properties of Mo2FeB2 based cermets [J]. Materials Research Express, 2017, 4(10): 106518.

ONUOHA C C, KIPOUROS G J, FARHAT Z N, et al. The reciprocating wear behaviour of TiC-304L stainless steel composites prepared by melt infiltration [J]. Wear, 2013, 303(1/2): 321-333.

HE L, GAO Y, LI Y, et al. Effect of milling time on powder's structure evolution of Ti(C,N)-304 stainless steel cermet [J]. Materials Research Express, 2018, 5(3): 1-11.

王凯旋, 曾卫东, 邵一涛, 等. 基于体视学原理的钛合金显微组织定量分析 [J]. 稀有金属材料与工程, 2009, 38(3): 398-403.

WANG Kaixuan, ZENG Weidong, SHAO Yitao, et al. Quantification of microstructural features in titanium alloys based on stereology [J]. Rare Metal Materials and Engineering, 2009, 38(3): 398-403.

全国工业陶瓷标准化技术委员会. 精细陶瓷弯曲强度试验方法: GB/T 6569—2006 [S]. 北京: 中国标准出版社, 2009: 9.

MAKHELE-LEKALA L, LUYCKX S, NABARRO F R N. Semi-empirical relationship between the hardness, grain size and mean free path of WC-Co [J]. International Journal of Refractory Metals and Hard Materials, 2001, 19(4): 245-249.

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Design and Energy Absorption Characteristics of Self-Locking Concave Negative Poisson’s Ratio Structure

Effects of a New Post-Weld Heat Treatment Process on the Properties of Friction Stir Welded Joints

Fused Extrusion Material Additive Manufacturing for Mg/PCL Composites

Preparation and Performance Study of Polyetheretherketone/Hydroxyapatite Composite Implants

Effects of Particle Size and Content of Alumina Filler on Mechanical Properties of Epoxy Resin Composite Materials

Related Author

YANG Jinshui

LIU Xuchang

XU Yaoyao

HAO Qingxuan

AN Yingying

WU Zhibing

SUN Dongyang

LI Yongxiang

Related Institution

Automotive Engineering Research Institute, Guangzhou Automobile Group Corporation, Guangzhou 511434, China

Qingdao Innovation Development Base, Harbin Engineering University, Qingdao, Shandong 266000, China

College of Aerospace and Civil Engineering, Harbin Engineering University, Harbin 150001, China

Hubei Key Laboratory of Advanced Technology of Automobile Components, Wuhan University of Technology

Hubei Collaborative Innovation Center for Automotive Components Technology, Wuhan University of Technology,, Chin

⁰