Effects of Jet Nozzle Aspect Ratio and Reynolds Number on Flow and Heat Transfer Characteristics of Vortex Cooling

doi:10.7652/xjtuxb201512020

您当前的位置：

首页 >

文章列表页 >

Effects of Jet Nozzle Aspect Ratio and Reynolds Number on Flow and Heat Transfer Characteristics of Vortex Cooling

更新时间：2025-07-09

- Effects of Jet Nozzle Aspect Ratio and Reynolds Number on Flow and Heat Transfer Characteristics of Vortex Cooling
- Vol. 49, Issue 12, Pages: 124-129+143(2015)
- 作者机构：
  
  西安交通大学叶轮机械研究所,西安,710049
- 作者简介：
- 基金信息：
- DOI：10.7652/xjtuxb201512020
  CLC： TK474.7
- Online First：10 December 2015，
  
  Published：2015
- 稿件说明：
移动端阅览
Effects of Jet Nozzle Aspect Ratio and Reynolds Number on Flow and Heat Transfer Characteristics of Vortex Cooling[J]. 2015, 49(12): 124-129+143.
DOI：

Effects of Jet Nozzle Aspect Ratio and Reynolds Number on Flow and Heat Transfer Characteristics of Vortex Cooling[J]. 2015, 49(12): 124-129+143. DOI： 10.7652/xjtuxb201512020.

摘要

针对叶片前缘冷却流动与传热问题

建立了合理的旋流腔冷却结构。通过求解三维稳态RANS方程和标准k-ω湍流模型

数值分析了喷嘴长宽比和雷诺数对旋流冷却流动和传热的影响。基于数值计算结果对无量纲传热系数Nu、喷嘴长宽比C

和雷诺数Re进行方程拟合

得到旋流冷却的传热关联式。结果表明:冷气从喷嘴进口切向射入旋流腔并形成高速旋流

显著增强换热; 随着喷嘴长宽比从0.2增大到9

旋流外区面积、冷气速度和冷气湍流动能先减小后增大

冷气压力系数先增大后减小; 在大喷嘴长宽比时

Nu沿旋流腔周向和轴向的分布较为均匀; 随着雷诺数的增大

冷气在旋流腔中的流动结构不变

而冷气速度、湍流动能、压力系数和壁面Nu均显著增大; 平均Nu随着雷诺数的增大而显著增大

随着喷嘴长宽比的增大先减小然后增大; 传热关联式与数值计算结果的误差在10%以内

可以准确预测旋流冷却的换热系数。

Abstract

A proper vortex chamber structure is established in terms of blade leading edge cooling. The influence of jet nozzle aspect ratio and Reynolds number on flow field and heat transfer characteristics of vortex cooling is numerically analyzed by means of 3-D steady RANS equations coupled with standard k-ω turbulence model. Based on numerical data

the heat transfer correlations are summarized with respect to the Nusselt number

jet nozzle aspect ratio and Reynolds number. Results show that high speed rotational flow is formed by the impingement air

thus the heat transfer intensity is significantly enhanced. When jet nozzle aspect ratio increases from 0.2 to 9

the outer rotation region

air speed and turbulence kinetic energy decrease at first and then increase

while the static pressure ratio increases at first and then decreases. A larger jet nozzle aspect ratio results in more uniform Nusselt number distribution in the circumferential and axial direction. An increase in Reynolds number leads to pronounced increases in air speed

turbulence kinetic energy

static pressure ratio and wall Nusselt number. However

the flow characteristics are not sensitive to Reynolds number. The globally averaged Nusselt number increases as Reynolds number increases

but decreases at first and then increases as jet nozzle aspect ratio increases. The heat transfer correlation can be used to accurately predict the vortex cooling heat transfer coefficient with a deviation less than 10%.

关键词

Keywords

references

LIGRANI P M, OLIVEIRA M M, BLASKOVICH T. Comparison of heat transfer augmentation techniques [J]. AIAA Journal, 2003, 41(3): 337-362.

KREITH F, MARGOLIS D. Heat transfer and friction in turbulent vortex flow [J]. Applied Scientific Research: Section A, 1959, 8(1): 457-473.

HAY N, WEST P D. Heat transfer in free swirling flow in a pipe [J]. Journal of Heat Transfer, 1975, 97(3): 411-416.

LIGRANI P M, HEDLUND C R, THAMBU R, et al. Flow phenomena in swirl chambers [J]. Experiments in Fluids, 1998, 24(3): 254-264.

GLEZER B, MOON H K, O'CONNELL T. A novel technique for the internal blade cooling [C]∥Proceedings of the 1996 ASME Turbo Expo. New York, USA: ASME, 1996: V004T09A015.

HEDLUND C R, LIGRANI P M, GLEZER B, et al. Heat transfer in a swirl chamber at different temperature ratios and Reynolds numbers [J]. International Journal of Heat and Mass Transfer, 1999, 42(22): 4081-4091.

LING J P C W, IRELAND P T, HARVEY N W. Measurement of heat transfer coefficient distributions and flow field in a model of a turbine blade cooling passage with tangential injection [C]∥Proceedings of the 2006 ASME Turbo Expo. New York, USA: ASME, 2006: 325-340.

LIU Zhao, LI Jun, FENG Zhenping. Numerical study on the effect of jet slot height on flow and heat transfer of swirl cooling in leading edge model for gas turbine blade [C]∥Proceedings of the 2011 ASME Turbo Expo. New York, USA: ASME, 2011: 1495-1504.

JIANG Yuting, ZHENG Qun, YUE Guoqiang, et al. Numerical investigation of swirl cooling heat transfer enhancement on blade leading edge by adding water mist [C]∥Proceedings of the 2014 ASME Turbo Expo. New York, USA: ASME, 2014: V05AT12A019.

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Research on Unsteady Flow and Multi-Parameter Heat Transfer Coupling Mechanism for Liquid Metal Pulsating Crossflow Over Tube Bundles

Molecular Dynamics Simulation Study on Nanoscale Flow Interference Between Two Circular Cylinders

Pressure and Heat Transfer Measurements for Blade Surface in Short-Duration Wind Tunnel

Numerical Study on Characteristics of Flow and Heat Transfer of Steam Vortex Cooling for Blade Leading Edges

Numerical Simulation for Flow and Heat Transfer Characteristics in Steam-Cooled Square Ribbed Channel

Related Author

LIU Yingwen

CHEN Hui

JIANG Hantao

陶文铨

孙杰

何雅玲

李印实

许都纯

Related Institution

School of Energy and Power Engineering, Xi’an Jiaotong University, Xi’an 710049, China

State Key Laboratong of Multiphase Flow in Power Engineering, Xi'an Jiaotong University

School of Power and Energy, Northwestern Polytechnical University

Lanzhou Haimo Technologies Co. Ltd.

State Key Laboratory of Multiphase Flow in Power Engineering, Xi'an Jiaotong University

⁰