Multi-Objective Optimal and Modified Design for Wide Helical Gear

doi:10.7652/xjtuxb201408016

您当前的位置：

首页 >

文章列表页 >

Multi-Objective Optimal and Modified Design for Wide Helical Gear

更新时间：2025-07-09

- Multi-Objective Optimal and Modified Design for Wide Helical Gear
- Vol. 48, Issue 8, Pages: 91-97(2014)
- 作者机构：
  
  西北工业大学机电学院,西安,710072
- 作者简介：
- 基金信息：
- DOI：10.7652/xjtuxb201408016
  CLC： TH132
- Online First：10 August 2014，
  
  Published：2014
- 稿件说明：
移动端阅览
Multi-Objective Optimal and Modified Design for Wide Helical Gear[J]. 2014, 48(8): 91-97.
DOI：

Multi-Objective Optimal and Modified Design for Wide Helical Gear[J]. 2014, 48(8): 91-97. DOI： 10.7652/xjtuxb201408016.

摘要

通过理论齿面叠加修形曲面方法来设计斜齿轮修形齿面

根据齿轮接触分析、承载接触分析计算得到承载变形、接触线上的离散载荷及啮合刚度

应用弹流润滑剂理论确定离散点的局部摩擦系数

并通过Blok闪温公式获得齿面闪温

建立斜齿轮啮合型弯-扭-轴-摆10自由度动力学模型; 以承载传动误差幅值、齿面闪温最小、齿面载荷均匀及振动加速度最小为目标

通过改进的粒子群优化算法确定了最佳修形齿面。结果表明:修形后齿轮副重合度增加

载荷均匀

齿面闪温分布明显改善; 随转速、载荷的增加

啮合冲击逐渐增大

且随转速增加

啮合冲击激励较刚度激励的振动更加明显

因此共振的敏感性降低

多载荷承载传动误差幅值反映了振动随载荷变化趋势; 修形后传动误差幅值、啮合冲击降低

因此有效降低了系统振动。

Abstract

Multi-objective optimal design method according to the minimum amplitude of loaded transmission error(LTE)

flash temperature

loads sharing and minimum vibration is proposed to improve performance of high speed and heavy-duty wide helical gears. The modified tooth surfaces are represented by a sum of two vector functions determining the theoretical tooth surface and the deviations surface. The deformation

meshing stiffness and discrete loads on contact line of gears are achieved by tooth contact analysis and loaded tooth contact analysis

and the discrete local friction coefficient is determined with elastohydrodynamic lubrication

so discrete temperature is sought out following the Blok flash temperature formula

and a 10-DOF helical gears vibration model considering excitations of time-varying meshing stiffness and corner meshing impact is established. An improved algorithm is adopted to optimize the curve parameters to obtain the best deviation surface. The results show that more uniform load distribution

lower flash temperature and improved contact ratio are realized; the corner meshing impact increases with increasing loads and rotating speeds

the system vibration gets more sensitive to the latter than the former

so the resonance sensibility is dulled

the LTE amplitude under multi-loads reflects the varying trend.

关键词

Keywords

references

LI Z, MAO K. The tooth profile modification in gear manufacture[J]. Applied Mechanics and Materials, 2008(10/11/12): 317-321.

袁哲, 孙志礼, 王丹, 等. 基于遗传算法的直齿圆柱齿轮修形优化减振[J]. 东北大学学报: 自然科学版, 2010, 31(6): 874-876.

YUAN Zhe, SUN Zhili, WANG Dan. GA-based optimum profile modification of spur gears for vibration damping[J]. Journal of Northeastern University: Natural Science, 2010, 31(6): 874-876.

王成, 方宗德, 贾海涛, 等. 人字齿轮修形优化设计[J]. 航空动力学报, 2009, 24(6): 1433-1436.

WANG Cheng, FANG Zongde, JIA Haitao. Modification optimization of double helical gears[J]. Journal of Aerospace Power, 2009, 24(6): 1433-1436.

方宗德, 沈允文. 斜齿轮的抗胶合优化修形[J]. 航空动力学报, 1993, 8(1): 80-82.

FANG Zongde, SHEN Yunwen. Optimal tooth profile modification of helical gears for improving resistance to scuffing[J]. Journal of Aerospace Power, 1993, 8(1): 80-82.

尚振国, 王华. 宽斜齿轮修形有限元分析[J]. 农业机械学报, 2009, 40(2): 215-219.

SHANG Zhenguo, WANG Hua. Finite element analysis of modified wide helical gears[J]. Transactions of the Chinese Society for Agricultural Machinery, 2009, 40(2): 215-219.

方宗德, 沈允文. 斜齿轮三维修形的优化设计[J]. 机械工程学报, 1992, 28(6): 57-60.

FANG Zongde, SHEN Yunwen. Optimal design of 3-D modification of helical gear[J]. Chinese Journal of Mechanical Engineering, 1992, 28(6): 57-60.

LITVIN F L, GONZALEZ-PEREZ I, FUENTES A, et al. Design, generation and stress analysis of face gear drive with helical pinion[J]. Computer Methods in Applied Mechanics and Engineering, 2005, 194: 3870-3901.

LITVIN F L, FAN Q, VECCHIATO D, et al. Computerized generation and simulation of meshing of modified spur and helical gears manufactured by shaving[J]. Computer Methods in Applied Mechanics and Engineering, 2001, 190(39): 5037-5055.

方宗德. 修形斜齿轮承载接触分析[J]. 航空动力学报, 1997, 12(3): 251-254.

FANG Zongde. Tooth contact analysis of modification of helical gears[J]. Journal of Aerospace Power, 1997, 12(3): 251-254.

XU Hai. Development of a generalized mechanical efficiency prediction methodology for gear pairs[D]. Columbus, USA: The Ohio State University, 2005: 113-128.

方宗德. 斜齿轮齿面柔度矩阵与修形的有限元计算[J]. 航空动力学报, 1994, 9(3): 242-244.

FANG Zongde. Calculation on flexibility matrix and modification of helical gears by FEM[J]. Journal of Aerospace Power, 1994, 9(3): 242-244.

高创宽. 渐开线齿轮传动的混合弹流润滑研究[D]. 太原: 太原理工大学, 2005: 108-112.

杨沛然, 温诗铸. 线接触弹流问题一种新的解算方法及更准确的油膜厚度公式[R]. 北京: 清华大学, 1988.

李润方, 王建军. 齿轮系统动力学[M]. 北京: 科学出版社, 1997: 154-188.

武宝林, 杨素君, 姚俊红. 齿轮传动中啮合冲击的理论分析[J]. 机械科学与技术, 2003, 22(1): 55-57.

WU Baolin, YANG Sujun, YAO Junhong. Theoretical analysis on meshing impact of involute gears[J]. Mechanical Science and Technology for Aerospace Engineering, 2003, 22(1): 55-57.

蒋进科, 方宗德, 苏进展. 基于承载传动误差幅值最小的斜齿轮齿面修形优化设计[J]. 航空动力学报, 2013, 28(7): 1637-1643.

JIANG Jinke, FANG Zongde, SU Jinzhan. Optimal design of modified helical gear tooth surfaces based on the minimum amplitude of loaded transmission error[J]. Journal of Aerospace Power, 2013, 28(7): 1637-1642.

龚纯, 王正林. 精通Matlab最优化计算[M]. 北京: 电子工业出版社, 2009: 296-299.

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Study on Numerical Method of Thermal-Fluid-Structure Coupling for Turbine Blades and Its Application

Application of Alternating Frequency/Time Domain Method to Vibration Analysis on Damping Blade Systems Based on Microslip Dry Friction Model

Driving Comfort Simulation Based on Human Biomechanics Model Under Vibration

Influence of Shape Error of Rotor Measurement Section on Vibration Testing

Quantitative Prediction of Sound Radiation by Casing Vibration of Centrifugal Fan

Related Author

FENG Zhenping

GAO Shanghong

WANG Xiangyu

王尚锦 1

上官博 1

徐自力 2

刘雅琳 1

陆长德 1

Related Institution

School of Energy and Power Engineering, Xi'an Jiaotong University

School of Mechanical Engineering, Xi'an Jiaotong University

Institute of Industrial Design, Northwestern Polytechnical University

State Key Laboratory for Manufacturing Systems Engineering, Xi'an Jiaotong University

School of of Energy and Power Engineering, Xi'an Jiaotong University

⁰