Theoretical and Experimental Research on Lubrication Properties of Large Heavy Sliding Bearing

doi:10.7652/xjtuxb201405003

您当前的位置：

首页 >

文章列表页 >

Theoretical and Experimental Research on Lubrication Properties of Large Heavy Sliding Bearing

更新时间：2025-07-09

- Theoretical and Experimental Research on Lubrication Properties of Large Heavy Sliding Bearing
- Vol. 48, Issue 5, Pages: 15-20(2014)
- 作者机构：
  
  西安交通大学现代设计及转子轴承系统教育部重点实验室,西安,710049
- 作者简介：
- 基金信息：
- DOI：10.7652/xjtuxb201405003
  CLC： TK262
- Online First：10 May 2014，
  
  Published：2014
- 稿件说明：
移动端阅览
Theoretical and Experimental Research on Lubrication Properties of Large Heavy Sliding Bearing[J]. 2014, 48(5): 15-20.
DOI：

Theoretical and Experimental Research on Lubrication Properties of Large Heavy Sliding Bearing[J]. 2014, 48(5): 15-20. DOI： 10.7652/xjtuxb201405003.

摘要

以单机容量1 750 MW级核电半速发电机试验用椭圆轴承为对象

在现场全尺寸动平衡机上进行了轴承性能试验

由此给出了椭圆轴承温度、压力和膜厚等润滑性能实测数据; 采用基于经典润滑理论的基本方程

运用流体润滑软件和ANSYS软件

在计入瓦体变形的基础上联合进行了轴承静态性能求解。结果表明:大型重载轴承瓦面热弹变形与油膜厚度为同一数量级

轴承设计中必须予以考虑; 额定转速为1 500 r/min时

轴承测点最高瓦温为82.8 ℃

测点最大油膜压力为6.65 MPa

瓦温和油膜压力仿真值与测试值偏差均小于5%; 在额定转速附近

最小油膜厚度测试值约为254 μm

仿真值与涡流法测试值的偏差为15.21%; 转速在1 000～1 600 r/min范围内

最小油膜厚度的仿真值与涡流法测试值的最大偏差为21.36%。理论和试验验证了考虑瓦体变形的润滑计算方法在大型重载轴承应用上是可行的。

Abstract

The elliptical bearings for the nuclear power generator are tested on the full-size balancing machine with single generator capacity of 1 750 MW. The tile temperature

oil film pressure

oil film thickness and other lubricating properties of the elliptical bearings are measured. The bearing calculation software and ANSYS are combined to evaluate the static performances considering the tile surface deformation. The results show that the tile surface thermo-elastic deformation gets the same magnitude of film thickness

thus the tile deformation ought be attended in the design of large heavy sliding bearings. At the rated speed of 1 500 r/min

the highest tile temperature reaches 82.8 ℃ and the maximum oil film pressure reaches 6.65 MPa at the measuring points. The deviations of temperature and pressure between the prediction and experiments get less than 5%. The minimum film thickness is measured as 254 μm at the rated speed and the deviations reaches 15.21%

the maximum error reaches 21.36% at the speed of 1 000-1 600 r/min.

关键词

Keywords

references

徐海波, 朱均. 离心力和热弹变形对大型水轮机推力轴承性能的影响[J]. 西安交通大学学报, 1993, 27(1): 63-71.

XU Haibo, ZHU Jun. Effects of centrifugal force and pad thermal-elastic deformation on large thrust bearing of hydro-electric generating set[J]. Journal of Xi'an Jiaotong University, 1993, 27(1): 63-71.

钟海权. 三峡水轮发电机6 000 t级推力轴承热弹流理论研究[J]. 东方电机, 1995(1): 9-14.

ZHONG Haiquan. TEHL analysis of thrust bearing with 6000t force of turbine generator used in the Three Gorges[J]. Dongfang Electrical Machine, 1995(1): 9-14.

李忠, 袁小阳, 朱均. 碟形弹簧支承圆形瓦推力轴承热动力润滑性能分析[J]. 摩擦学学报, 1999, 19(2): 135-139.

LI Zhong, YUAN Xiaoyang, ZHU Jun. A study of the thermohydrodynamic lubrication performance of thrust bearing with plate-spring supported circular pads[J]. Tribology, 1999, 19(2): 135-139.

朱均. 滑动轴承油膜非线性动力学分析[J]. 太原重型机械学院学报, 2004, 25(S1): 4-7.

ZHU Jun. Nonlinear dynamic analysis of oil film about sliding bearing[J]. Journal of Taiyuan Heavy Machinery Institute, 2004, 25(S1): 4-7.

常秋英, 孟永钢, 温诗铸, 等. 径向可倾瓦轴承的热弹流润滑分析[J]. 机械工程学报, 2002, 38(9): 77-82.

CHANG Qiuying, MENG Yonggang, WEN Shizhu, et al. TEHL analysis of tilting-pad journal bearings with Newton-Raphson method[J]. Chinese Journal of Mechanical Engineering, 2002, 38(9): 77-82.

徐华. 轴瓦弹性变形对大型径向可倾瓦轴承性能的影响的研究[D]. 西安: 西安交通大学, 1984.

REDDY D S K, SWARNAMANI S, PRABHU B S. Thermoelastohydrodynamic analysis of tilting pad journal bearing: theory and experiments[J]. Tribology Transactions, 2000, 43(1): 82-90.

BOUYER J, FILLON M. On the significance of the thermal and deformation effects on a plain journal bearing subjected to severe operating conditions[J]. Journal of Tribology, 2004, 126(4): 819-822.

刘莹, 郭溪泉. 高速重载径向滑动轴承热弹性计算方法的研究[J]. 钢铁, 1999, 1(1): 1-11.

LIU Ying, GUO Xiquan. Thermal-elastohydrodynamic method for high speed heavy load journal bearing[J]. Iron and Steel, 1999, 1(1): 1-11.

方静辉, 汪久根, 陈志祥. 卧式水电机组用径向滑动轴承热弹流特性分析[J]. 润滑与密封, 2012, 37(1): 56-61.

FANG Jinghui, WANG Jiugen, CHEN Zhixiang. Thermal elastohydrodynamic lubrication performance of journal bearing for bulb type hydraulic power unit[J]. Lubrication Engineering, 2012, 37(1): 56-61.

张勇, 莫森泉, 王佳. 径向滑动轴承弹流润滑耦合求解[J]. 轴承, 2010(4): 11-15.

ZHANG Yong, MO Senquan, WANG Jia. Coupling algorithm for EHL of journal bearings[J]. Bearing, 2010(4): 11-15.

MARUYAMA A, SAITOH T. Oil film behavior under minute vibrating conditions in EHL point contacts[J]. Tribology International, 2010, 43(8): 1279-1286.

YAGI A, VERGNE P, NAKAHARA T. In situ pressure measurements in dimpled elastohydrodynamic sliding contacts by Raman microspectroscopy[J]. Tribology International, 2009, 42(5): 724-730.

CHAPKOVA A D, BAIRB S, CANNC P, et al. Film thickness in point contacts under generalized Newtonian EHL conditions: numerical and experimental analysis[J]. Tribology International, 2007, 40(10/11/12): 1474-1478.

CIULLI E, STADLER K, DRAEXL T. The influence of the slide-to-roll ratio on the friction coefficient and film thickness of EHD point contacts under steady state and transient conditions[J]. Tribology International, 2009, 42(4): 526-534.

CARLI M, SHARIF K J. Thermal point contact EHL analysis of rolling/sliding contacts with experimental comparison showing anomalous film shapes[J]. Tribology International, 2009, 42(4): 517-525.

赵卫军. 1000MW机组开槽椭圆轴承的实验研究[D]. 西安: 西安交通大学, 2012.

JI Feng, GUO Yong, YUAN Xiaoyang, et al. Turbulent model analysis and experimental research for lubrication performance of large power units journal bearing[C]∥Proceedings of IEEE Conference on Industrial Electronics and Applications. Piscataway, NJ, USA: IEEE, 2009: 206-210.

刘松亚. 考虑载荷影响的大尺寸椭圆轴承性能仿真及试验[D]. 西安: 西安交通大学, 2012.

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Analysis on Lubrication Performance of Fluid Pivot Tilting Pad Journal Bearings

Development of Combined Self-Decoupling Piezoelectric Thin Film Three-Dimensional Force Sensor

Bi-Level Multi-Obj ective Optimization of a Wind-Solar Coupled Hydrogen Production System Based on the Synergy of Hybrid Electrolyzer Arrays

Integrated and Joint Design Optimization of Centrifugal Compressor Impeller and Casing Treatment at Multiple Working Points

Sensitivity Analysis of Foil Geometrical Parameters for the Third-Generation CO2 Gas Foil Bearings Based on Design of Experiments Method

Related Author

王晓红

常山

裴世源

ZHAO Peng

WANG Guicong

LI Yingjun

YANG Zhikang

Related Institution

No.703 Research Institute of China State Shipbuilding Corporation Limited

(School of Mechanical Engineering, Jinan University,,)

⁰