Freeze-Drying Defect Control of Alumina-Based Ceramic Body Prepared with Gel Casting Technology

doi:10.7652/xjtuxb201401021

您当前的位置：

首页 >

文章列表页 >

Freeze-Drying Defect Control of Alumina-Based Ceramic Body Prepared with Gel Casting Technology

更新时间：2025-07-09

- Freeze-Drying Defect Control of Alumina-Based Ceramic Body Prepared with Gel Casting Technology
- Vol. 48, Issue 1, Pages: 123-126+132(2014)
- 作者机构：
  
  西安交通大学机械制造系统工程国家重点实验室,西安,710049
- 作者简介：
- 基金信息：
- DOI：10.7652/xjtuxb201401021
  CLC： O121.8;G558
- Online First：10 January 2014，
  
  Published：2014
- 稿件说明：
移动端阅览
Freeze-Drying Defect Control of Alumina-Based Ceramic Body Prepared with Gel Casting Technology[J]. 2014, 48(1): 123-126+132.
DOI：

Freeze-Drying Defect Control of Alumina-Based Ceramic Body Prepared with Gel Casting Technology[J]. 2014, 48(1): 123-126+132. DOI： 10.7652/xjtuxb201401021.

摘要

采用凝胶注模成型技术制造复杂精铸件陶瓷铸型的过程中

铸型坯体会产生内部裂纹等缺陷

严重影响铸型质量。为此

采用三维CT检测技术

通过实验跟踪内部裂纹产生的过程

发现在冷冻干燥失水率(质量比)为20%～60%时

坯体容易产生裂纹。基于冷冻干燥理论

对裂纹产生的机理进行了分析

结果表明:在坯体冷冻干燥过程中

若冻结层温度高于其共晶点温度(-3.6 ℃)

将使冻结层融化

致使其强度急剧下降

从而导致裂纹产生。为了降低坯体冻结层温度

将干燥供热板温度从15 ℃降低为-5 ℃

并在坯体内部设计直径为0.8 mm的通孔结构

结果表明:采用这2项措施后

当坯体失水率为20%～60%时

可保证冻结层温度低于-3.6 ℃

有效避免裂纹的产生。

Abstract

In producing precision ceramic casting mould of complex components by gel casting technology

the internal cracks generated in the freeze-drying process affect the mould quality seriously. In this study

computer tomography(CT)was employed to track the crack generation. The results show that internal cracks occur when water loss rate is within 20%-60%. According to the freeze-drying theory

the internal crack generation mechanism in gel casting ceramic body is analyzed. When the temperature of the subsurface gets higher than the eutectic temperature of the green body(-3.6 ℃)in the rapid ice sublimation stage(in which the water loss rate is about 20%-60%)

the frozen layer melts to result in a dramatic drop in strength and an increase in drying stress

leading to cracks generation. Lowering the drying temperature(from 15 ℃ to -5 ℃)and setting through holes of 0.8 mm in diameter in the green body can keep the subsurface temperature lower than the eutectic temperature in the rapid ice sublimation stage to prevent the crack generation effectively.

关键词

Keywords

references

JANNEY M A. Method for molding ceramic powders: US, 4894194[P]. 1990-01-16.

JANNEY M A, NUNN S D, WALLS C A, et al. The handbook of ceramic engineering[M]. New York, USA: Marcel Dekker, 1998: 13-15.

JANNEY M A, OMATETE O O. Method for molding ceramic powders using a water-based gelcasting: US, 5028362[P]. 1991-06-02.

KRAUSE C. ORNL's gelcasting: molding the future of ceramic forming?[EB/OL].[2013-04-21]. http:∥www.ornl.gov/info/ornlreview/rev28-4/text/gelcast.htm.

吴海华. 空心涡轮叶片型芯型壳一体化陶瓷铸型快速制造技术研究[D]. 西安: 西安交通大学, 2009.

张立明. 陶瓷悬浮液流变特性及胶态成型坯体缺陷的控制[D]. 北京: 清华大学, 2005.

奚红霞, 黄仲涛. 凝胶的干燥[J]. 膜科学与技术, 1997, 17(1): 1-7.XI Hongxia, HUANG Zhongtao. Drying of gels[J]. Membrane Science and Technology, 1997, 17(1): 1-7.

SCHERERM G W. Crack-tip stress in gels[J]. Non-Crystalline Solids, 1992, 144(3): 210-216.

华泽钊. 冷冻干燥新技术[M]. 北京: 科学出版社, 2006: 153, 167-168.

苏树强, 丁志华, 华泽钊. 冻干过程中升华界面温度测量方法的研究[J]. 工程热物理学报, 2004, 25(5): 852-854.

SU Shuqiang, DING Zhihua, HUA Zezhao. Study on the measurement of the product temperature at the moving sublimation interface during the freeze drying process[J]. Journal of Engineering Thermophysics, 2004, 25(5): 852-854.

徐成海. 真空干燥技术[M]. 北京: 化学工业出版社, 2011: 45-47.

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Particle Segregation Control in Fabricating Ceramic Mold for Hollow Turbine Blades During Gel-Casting

Gelcasting Filling for Small Structure of Hollow Turbine Blade Ceramic Mold

Integrated and Joint Design Optimization of Centrifugal Compressor Impeller and Casing Treatment at Multiple Working Points

I/O Performance Modeling and Prediction Method for Large-Scale Parallel Applications Using Machine Learning

Turbulent Kinetic Energy Dissipation Mechanism of Supercritical Carbon Dioxide Leakage Flow in a Scallop Bionic Seal Cavity

Related Author

姜博

鲁中良

苗恺

周江平

李涤尘

杨强 1

鲁中良 1

Related Institution

State Key Laboratory for Manufacturing Systems Engineering, Xi'an Jiaotong University

Collaborative Innovation Center of High-End Manufacturing Equipment, Xi'an Jiaotong University

⁰