Stiffness Matching Design for Feed System of High-Speed Machine Tool Considering Modal Characteristics

doi:10.7652/xjtuxb201401015

您当前的位置：

首页 >

文章列表页 >

Stiffness Matching Design for Feed System of High-Speed Machine Tool Considering Modal Characteristics

更新时间：2025-07-09

- Stiffness Matching Design for Feed System of High-Speed Machine Tool Considering Modal Characteristics
- Vol. 48, Issue 1, Pages: 90-95(2014)
- 作者机构：
  
  西安交通大学机械制造系统工程国家重点实验室,西安,710049
- 作者简介：
- 基金信息：
- DOI：10.7652/xjtuxb201401015
  CLC： TH122
- Online First：10 January 2014，
  
  Published：2014
- 稿件说明：
移动端阅览
Stiffness Matching Design for Feed System of High-Speed Machine Tool Considering Modal Characteristics[J]. 2014, 48(1): 90-95.
DOI：

Stiffness Matching Design for Feed System of High-Speed Machine Tool Considering Modal Characteristics[J]. 2014, 48(1): 90-95. DOI： 10.7652/xjtuxb201401015.

摘要

为了得到进给系统的最优动态特性

建立了进给系统的动力学模型。采用有限元法对高速机床进给系统的部件与结合面进行刚度设计

通过分析进给系统的振动形式

找出了在各种因素下系统模态参数的变化规律

以工作台的结构设计为例

进行了合理的刚度匹配。进给系统在低频段沿进给方向振动

最显著的影响因素是工作台的质量、丝杠-螺母副接触刚度、轴承副接触刚度和丝杠自身的拉压刚度

当系统沿垂直于工作台的方向振动时

受导轨-滑块结合面刚度的影响较大。在不同导轨、滑块跨距组合参数下

对系统模态的特性变化规律进行了分析

当滑块跨距为400 mm、导轨跨距为300 mm时

系统模态为最优分布。研究表明

该刚度匹配设计方法可使工作台的质量减小10%

进给系统的1阶固有频率提高9%

从而验证了该方法的准确性。

Abstract

To obtain the optimum dynamic characteristics of feed system

a dynamic model of the system is set up with finite element method to carry out the matching design of components and joint interfaces for high-speed machine tool. Analyzing the vibrating mode of the feed system

the changing rule of system mode parameters due to various factors is revealed. The optimization of the inner table structure is taken as an example to illustrate the matching design. When the system vibrates in feeding direction

the important affecting factors are table mass

screw-nut joint stiffness

bearing stiffness and screw stiffness itself

but when the system vibrates in direction normal to the table

the guideway joint interface stiffness dominates. Investigating the changing modes in different corporations of guideway spans and slides

the optimum result is found: the slide span of 400 mm and guideway span of 300 mm. The table mass can be reduced by 10% and the first-order frequency of the system increased by 9%.

关键词

Keywords

references

VERL S. Correlation between feed velocity and preloading in ball screw drives[J].CIRP Annals-Manufacturing Technology, 2010, 59(1): 429-432.

NEUGEBAUER R, DENKENA B, WEGENER K. Mechatronic systems for machine tools[J]. Annals of the CIRP, 2007, 56(2): 657-686.

卢秉恒, 赵万华, 张俊.高速高加速度下的进给系统机电耦合[J].机械工程学报, 2013, 49(6): 2-10.

LU Bingheng, ZHAO Wanhua, ZHANG Jun. Electromechanical coupling in the feed system with high speed and high acceleration[J].Journal of Mechanical Engineering, 2013, 49(6): 2-10.

LIANG Mi, YIN Guofu, SUN Mingnan, et al. Effects of preloads on joints on dynamic stiffness of a whole machine tool structure[J].Journal of Mechanical Science and Technology, 2012, 26(2): 495-508.

HUNG Juipin, LAI Yuanlung, LIN Chingyuan, et al. Modeling the machining stability of a vertical milling machine under the influence of the preloaded linear guide[J].International Journal of Machine Tools Manufacture, 2011, 51(9): 731-739.

LIN Chingyuan, HUNG Juipin. Effect of preload of linear guides on dynamic characteristics of a vertical column-spindle system[J].International Journal of Machine Tools Manufacture, 2010, 50(1): 741-746.

FENG Guohua, PAN Yilu. Investigation of ball screw preload variation based on dynamic modeling of a preload adjustable feed-drive system and spectrum analysis of ball-nuts sensed vibration signals[J].International Journal of Machine Tools Manufacture, 2012, 52(1): 85-96.

GREENWOOD J A. Analysis of elliptical Hertzian contacts[J]. Tribology International, 1997, 30(3): 235-237.

冈本纯三.球轴承的设计计算[M].黄志强, 译.北京: 机械工业出版社, 2003: 1-14.

BREWE D E, HAMROCK B J. Simplified solution for elliptical-contact deformation between two elastic solids[J]. Journal of Lubrication Technology, 1977, 99(4): 485-487.

RIVIN E I. Stiffness and damping in mechanical design[M].New York, USA: Marcel Dekker Inc, 1999: 266-271.

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Bifurcation and Chaos Characteristics for Ball-Screw System Considering Nonlinear Elastic Force

Dynamic Characteristics of Mechanical System in Linear Motor Feed System

Analysis and Prediction for Thermal Error of Precision Coordinate Boring Machine

Mechanism and Optimal Control Strategy for Hysteresis in Rapid Dehumidification Response of Indirect Thermal Systems in Electric Vehicles

Sensitivity Analysis of Foil Geometrical Parameters for the Third-Generation CO2 Gas Foil Bearings Based on Design of Experiments Method

Related Author

吴沁 1

芮执元 1

杨建军 1

杨晓君

赵万华

刘辉

Related Institution

Key Laboratory of Digital Manufacturing Technology and Application, The Ministry of Education, Lanzhou University of Technology

School of Mechanical and Electronical Engineering, Lanzhou University of Technology

⁰