Position of Support Force on Cylinder in Internal-Meshing Cycloid Rotary Compressor

冯诗愚 1; 朱冬生 2; 高秀峰 1; 李云 1; 刘卫华 3

您当前的位置：

首页 >

文章列表页 >

Position of Support Force on Cylinder in Internal-Meshing Cycloid Rotary Compressor

更新时间：2025-12-08

- Position of Support Force on Cylinder in Internal-Meshing Cycloid Rotary Compressor
- Vol. 41, Issue 11, Pages: 1257-1261(2007)
- 作者机构：
  
  西安交通大学能源与动力工程学院,西安,710049
- 作者简介：
- 基金信息：
- DOI：
  CLC： TH45
- Online First：10 November 2007，
  
  Published：2007
- 稿件说明：
移动端阅览
冯诗愚 1, 朱冬生 2, 高秀峰 1, et al. Position of Support Force on Cylinder in Internal-Meshing Cycloid Rotary Compressor[J]. 2007, 41(11): 1257-1261.
DOI：

冯诗愚 1, 朱冬生 2, 高秀峰 1, et al. Position of Support Force on Cylinder in Internal-Meshing Cycloid Rotary Compressor[J]. 2007, 41(11): 1257-1261. DOI：

摘要

为了限制内啮合摆线转子压缩机中外转子绕内转子公转的趋势

在外转子上施加一个支撑力

对支撑力的位置进行了详细分析.研究结果表明

内啮合摆线转子压缩机中支撑力的方向和位置完全是由几何关系决定的

而与气体力、接触力等无关

因此在对该压缩机进行受力分析时

必须首先确定支撑力位置

然后再计算支撑力和接触力.该研究可为内啮合摆线转子压缩机的动力学设计提供参数.

Abstract

The outer rotor has the trend of revolution along the inner rotor and this trend must be overcome by the cylinder via the action of a support force in an internal-meshing rotary cycloid compressor. The position of the support force was analyzed with certain simplification by applying tolerance or clearance of all meshing surfaces. The result shows that the direction and position of the support are only determined by the geometric relationship instead of the gas force and contact force. It is suggested that the position of the support force should be firstly obtained before the calculation of the support force and contact force.

关键词

Keywords

references

顾兆林,郁永章,高秀峰,等. 一种制冷系统用转子压缩-膨胀机:中国,ZL02145524.4[P].2003-12-24.

野阪倫保,高原康男,及部一夫.トロュィド型冷媒壓縮機:日本,7-310686[P].1995-05-20.

郁永章. 高强度、全平衡转子式压缩机: 中国,ZL 00226465.X[P]. 2003-11-05.

毛华永,李国祥,徐秀兰,等.摆线转子泵的工作原理及特点[J].山东内燃机,2002,73(3):33-35.

Mao Huayong, Li Guoxiang, Xu Xiulan, et al. Working principle and its characteristic of cycloid rotary pump [J]. Shandong Internal Combustion Engine, 2002, 73(3): 33-35.

Mimmi G C, Pennacchi P E. Involute gear pumps versus lobe pumps: a comparison[J].Transactions of ASME:Journal of Mechanical Design, 1997, 119(12): 458-465.

张旭东,郁永章.一种新型全平衡高强度转子式压缩机的受力分析[J].西安交通大学学报,2001, 35(12):1305-1309.

Zhang Xudong, Yu Yongzhang. Mechanical analysis of a new rotary compressor[J]. Journal of Xi'an Jiaotong University, 2001, 35(12): 1305-1309.

郁永章,张旭东.一种新型全平衡高强度转子式压缩机的几何关系[J].西安交通大学学报,2001,35(11): 1193-1197.

Yu Yongzhang, Zhang Xudong. Geometry relations of a new rotary compressor[J]. Journal of Xi'an Jiaotong University, 2001, 35(11): 1193-1197.

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Modification of Profile for Internal-Meshing Cycloid Rotary Compressor

Kinetic Property Influenced by Clearances in Internal-Meshing Cycloid Rotary Compressor

Numerical Simulation of the Energy Conversion Process in Thermoacoustic Engines with Different Stack Materials

Sensitivity Analysis of Foil Geometrical Parameters for the Third-Generation CO2 Gas Foil Bearings Based on Design of Experiments Method

Diffusion Characteristics and Influencing Factors in Case of Hydrogen Leakage from Fuel Cell Vehicles Running in Tunnels

Related Author

刘卫华 2

王赞社 1

胡伟 2

刘卫华 3

顾兆林 2

Related Institution

School of Energy and Power Engineering, Xi'an Jiaotong University

⁰