Exergy Analysis of Exhaust Steam Reclaim Device with Injector

您当前的位置：

首页 >

文章列表页 >

Exergy Analysis of Exhaust Steam Reclaim Device with Injector

更新时间：2025-07-09

- Exergy Analysis of Exhaust Steam Reclaim Device with Injector
- Vol. 44, Issue 5, Pages: 1-4+90(2010)
- 作者机构：
  
  西安交通大学动力工程多相流国家重点实验室,西安,710049
- 作者简介：
- 基金信息：
- DOI：
  CLC： TK11
- Online First：10 May 2010，
  
  Published：2010
- 稿件说明：
移动端阅览
Exergy Analysis of Exhaust Steam Reclaim Device with Injector[J]. 2010, 44(5): 1-4+90.
DOI：

Exergy Analysis of Exhaust Steam Reclaim Device with Injector[J]. 2010, 44(5): 1-4+90. DOI：

摘要

建立了喷射式低温乏汽回收利用装置的火用分析模型.对比研究了无旋流、水旋流、蒸汽旋流、水汽旋流4种结构形式下装置火用效率的变化规律

分析了喉嘴距、混合腔收缩角、喉嘴面积比等结构参数对装置火用效率的影响

研究了水旋流形式下装置火用效率随汽水参数变化的规律.发现最佳的结构形式为水旋流结构

最佳的结构参数为:喉嘴距L=145 mm、收缩角θ=18°、面积比M=5.44

得出装置火用效率随进水温度和进汽压力的增加而增加

随进水压力的增加而降低.研究结果可为装置结构的优化和运行参数的选择提供依据.

Abstract

An exergy analysis model of an exhaust steam reclaim device with injector was established. The variation of exergy efficiency was compared under four different structures(without-swirling

water-swirling

steam-swirling and steam-water-swirling)on the basis of the experiment. The influences of the different structure parameters(spout-throat distance

contract angle and area ratio)of the injector and different steam-water parameters on the exergy efficiency of the device were analyzed. The results show that the adoption of the water-swirling structure can obtain the optimum exergy efficiency. Moreover

the exergy efficiency reaches the highest value at the spout-throat distance of 145 mm

the contract angle of 18°

and the area ratio of 5.44. In addition

the exergy efficiency of the injector increases with the increase in the inlet water temperature and the inlet steam pressure and decreases with the increase in the inlet water pressure.

关键词

Keywords

references

YAN Junjie, SHAO Shufeng, LIU Jiping, et al. Experiment and analysis on performance of steam-driven jet injector for district-heating system[J]. Applied Thermal Engineering, 2005, 25:1153-1167.

DEBERNE N, LEONE J F, DUQUE A, et al. A model for calculation of steam injector performance[J]. International Journal of Multiphase Flow, 1999, 25: 841-855.

NARABAYASHI T, MIZUMACHI W, MORI M. Study on two-phase flow dynamics in steam injectors [J]. Nuclear Engineering and Design, 1997, 175:147-156.

祝银海, 厉彦忠, 鱼剑琳, 等. 一种新的喷射器模型及其实验验证[J]. 西安交通大学学报,2008,42(9):1096-1101.

ZHU Yinhai, LI Yanzhong, YU Jianlin, et al. Novel ejector model with experimental validation[J]. Journal of Xi'an Jiaotong University, 2008, 42(9):1096-1101.

SUN Dawen. Variable geometry ejectors and their applications in ejector refrigeration systems[J]. Energy, 1996,10(21):919-929.

李小龙,张朋飞,严俊杰,等. 旋流喷射乏汽回收装置性能的实验研究[J]. 工程热物理学报,2009,30(7):799-802.

LI Xiaolong, ZHANG Pengfei, YAN Junjie, et al. Experimental study on the performance of exhaust steam reclaim device by jetting vortically[J]. Journal of Engineering Thermophysics, 2009,30(7):799-802.

张朋飞,李小龙,严俊杰,等. 低温乏汽回收利用装置性能的实验研究[J]. 工程热物理学报, 2009,30(7):1152-1154.

ZHANG Pengfei, LI Xiaolong, YAN Junjie, et al. Experimental research on the performance of the low temperature exhaust steam reclamation device[J]. Journal of Engineering Thermophysics, 2009,30(7):1152-1154.

YAN Junjie, CHONG Daotong, WU Xinzhuang. Effect of swirling vanes on performance of steam-water jet injector[EB/OL].[2009-11-07].http:∥www.sciencedirect.com/science.

严俊杰,杨建军,张朋飞,等. 低温乏汽回收利用装置的结构参数研究[J]. 西安交通大学学报,2010,44(1):1-4.

YAN Junjie, YANG Jianjun, ZHANG Pengfei, et al. Influence of structure parameters on performance of low temperature exhaust steam recovery device[J]. Journal of Xi'an Jiaotong University, 2010,44(1):1-4.

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Influence of Structure Parameters on Performance of Low-Temperature Exhaust Steam Recovery Device

A Structure-Semantics-Residual Collaborative Image Compression Framework：Towards Privacy Protection and High-Fidelity Reconstruction

Review of the Application of EBSILON Software in Combined Heat and Power System Optimization

Sensitivity Analysis of Foil Geometrical Parameters for the Third-Generation CO2 Gas Foil Bearings Based on Design of Experiments Method

Diffusion Characteristics and Influencing Factors in Case of Hydrogen Leakage from Fuel Cell Vehicles Running in Tunnels

Related Author

李波

Related Institution

No data

⁰