Erosion-Wear Resistance of Series α-Al<sub>2</sub>O<sub>3</sub> Structure Ceramics

您当前的位置：

首页 >

文章列表页 >

Erosion-Wear Resistance of Series α-Al₂O₃ Structure Ceramics

更新时间：2025-07-09

- Erosion-Wear Resistance of Series α-Al₂O₃ Structure Ceramics
- Vol. 44, Issue 5, Pages: 71-74(2010)
- 作者机构：
  
  西安交通大学材料科学与工程学院,西安,710049
- 作者简介：
- 基金信息：
- DOI：
  CLC： TG174.1
- Online First：10 May 2010，
  
  Published：2010
- 稿件说明：
移动端阅览
Erosion-Wear Resistance of Series α-Al₂O₃ Structure Ceramics[J]. 2010, 44(5): 71-74.
DOI：

Erosion-Wear Resistance of Series α-Al₂O₃ Structure Ceramics[J]. 2010, 44(5): 71-74. DOI：

摘要

以冲蚀磨损工况下的泵用材料Cr15Mo3高铬铸铁为对比材料

采用转盘式液-固双相流试验机研究了系列α-Al

结构陶瓷(90瓷、95瓷、99瓷)的耐冲蚀磨损性能及微观失效机制.结果表明:在不同磨粒硬度试验条件下

Cr15Mo3的冲蚀磨损率均比α-Al

结构陶瓷的高4～6倍

且随着磨粒硬度的增加

Cr15Mo3的冲蚀磨损率增加幅度更大; α-Al

结构陶瓷的冲蚀磨损体积随磨料含量的增加略有增加

但在相同磨粒硬度试验条件下相差不大

因此该工况下可使用90瓷或95瓷

从而提高应用材料的性价比; Cr15Mo3的微观失效有明显的方向性和腐蚀痕迹

主要以微切削、犁沟和冲蚀坑等形式为主

而α-Al

结构陶瓷的失效主要是晶界玻璃相失去

有少量冲蚀坑和晶粒剥落痕迹

迅速增加径向和横向断裂表面能是其主要耗能方式.

Abstract

Erosion resistance of series α-Al

ceramics is investigated by water slurry with different abrasive particles hardness on a liquid-solid dual phase erosion test machine. High chromium cast iron Cr15Mo3 for industrial pumps is taken as a reference material in the erosion-wear test. The erosion-wear failure mechanism of the test materials in slurry erosion is discussed. The result shows that the slurry erosion volume of Cr15Mo3 is 4 to 6 times larger than that of series α-Al

ceramics with the different abrasive particles hardness

and increases with the increasing abrasive particles hardness. The slurry erosion volume of series α-Al

ceramics s

lightly increases with the increasing volume fraction of α-Al

therefore the ceramics with 90% or 95% volume fraction of α-Al

may replace the one with 99% volume fraction of α-Al

in most cases to lower the material cost. It is observed by SEM that there exist obvious corrosive and erosive pits on the worn surface of Cr15Mo3 iron

while a little such pits and particle stripping-off pits on the worn surface of the α-Al

ceramics. The failure of the α-Al

ceramics is mainly due to losing the binding phase in crystal boundary. The major mode of energy consumption of α-Al

ceramics is rapidly increasing radial and transverse fracture surface energy.

关键词

Keywords

references

周庆德,饶启昌,方亮,等. 4PH 杂质泵过流部件(护套)的磨损失效分析[C]∥ 周庆德,饶启昌,苏俊义. 铬系抗磨铸铁. 西安: 西安交通大学出版社,1987: 226-229.

ZHENG Yugui, YAO Zhiming, WEI Xiangyun, et al. The synergistic effect between erosion and corrosion in acidic slurry media [J]. Wear, 1995,186/187(6): 555-561.

WEBER J. Flow induced corrosion: 25 years of industrial research [J]. British Corrosion Journal, 1992,27(3): 193-199.

SHALABY H M, ATTARI S, RIAD W T. Erosion-corrosion behavior of some cast alloys in seawater [J]. Corrosion, 1992, 48(3): 206-217.

李卫. 热强碱性铝矿浆冲刷腐蚀及抗磨蚀铸铁材料的研究[D]. 西安:西安交通大学机械工程学院, 2001.

ALLEN C, BALL A. A review of the performance of engineering materials under prevalent tribological and wear situations in South Africa industries [J]. Tribology International, 1996, 29(5): 105-116.

WANG Dongfang, MAO Zhiyu. A study for erosion of Si3N4 ceramics by impact of solid particles [J].Wear, 1996, 196/199(2): 283-286.

ZHANG Yi, CHENG Yubing, LATHABA I S. Erosion of alumina ceramics by air- and water-suspended garnet particles [J]. Wear, 2000, 240(1/2): 40-51.

SCHWETZ K A, SIGL L S, GREIM J, et al. Wear of boron carbide ceramics by abrasive waterjets [J]. Wear, 1995, 181/183: 148-155.

BAO Chonggao, PAN Wei, MIAO Hezhou, et al. Study on the properties of structure ceramic on erosion-wear [J]. Key Engineering Materials, 2005, 280/283: 1323-1326.

张安峰. 新型试验机的研制与铬系白口铸铁相间腐蚀的基础研究[D]. 西安:西安交通大学机械工程学院, 2000.

HANCHI J, EISS N S. Tribological behavior of polyetheretherketone, a thermotropic liquid crystalline polymer and in situ composites based on their blends under dry sliding conditions at elevated temperatures [J]. Wear, 1996, 200(1/2): 105-121.

LU Zhaoping, ERIEXLRICH K. On sliding friction and wear of PEEK and its composites [J]. Wear, 1995, 181/183(2): 624-631.

HANCHI J H, EISS N S. Preliminary study of the elevated temperature tribological behavior of PEEK based in situ composites under unlubricated sliding conditions [J]. Tribology Transactions, 1995, 38(2): 305-310.

HANCHI J H, EISS N S. The Tribological behavior of blends of polyetheretherketone(PEEK)and polyetherimide(PEI)at elevated temperatures [J].Tribology International, 1994, 37(3): 495-504.

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Interaction Between Erosive-Wear and Corrosion of Alloy Materials for Hydroturbine in Hydroelectric Station

Influence of Structural Parameters on the Summer Operational Characteristics of a Three-Tower-in-One Indirect Air-Cooling System

A Fast Calculation Method for Thermal Flow Fields in Transformer Windings Based on PI-DeepONet

I/O Performance Modeling and Prediction Method for Large-Scale Parallel Applications Using Machine Learning

Energy Efficiency Optimization of the Cryogenic Air Separation Process for Electronic-Grade Ultra Pure Nitrogen

Related Author

鲍崇高

高义民

邢建东

Related Institution

No data

⁰

Erosion-Wear Resistance of Series α-Al2O3 Structure Ceramics

DOI：

摘要

Abstract

关键词

Keywords

references

Erosion-Wear Resistance of Series α-Al₂O₃ Structure Ceramics