Performance Influence Factors on Ti<sub>3</sub>SiC<sub>2</sub> Synthesized by Infiltration-Sintering Technology

您当前的位置：

首页 >

文章列表页 >

Performance Influence Factors on Ti₃SiC₂ Synthesized by Infiltration-Sintering Technology

更新时间：2025-07-09

- Performance Influence Factors on Ti₃SiC₂ Synthesized by Infiltration-Sintering Technology
- Vol. 44, Issue 5, Pages: 56-59(2010)
- 作者机构：
  
  西安理工大学材料科学与工程学院,西安,710049
- 作者简介：
- 基金信息：
- DOI：
  CLC： [TB331]
- Online First：10 May 2010，
  
  Published：2010
- 稿件说明：
移动端阅览
Performance Influence Factors on Ti₃SiC₂ Synthesized by Infiltration-Sintering Technology[J]. 2010, 44(5): 56-59.
DOI：

Performance Influence Factors on Ti₃SiC₂ Synthesized by Infiltration-Sintering Technology[J]. 2010, 44(5): 56-59. DOI：

摘要

采用熔渗反应烧结技术制备了Ti

SiC

材料

并对影响制备材料性能的因素进行了分析.研究结果表明:在熔渗温度为1 500 ℃、熔渗高度为6 mm时

最佳熔渗保温时间应为30 min; 随着制备试样中Ti

SiC

相的逐渐增多

材料的抗弯性能明显提高; 随着试验压力的增加

SiC

材料的摩擦因数和磨损率均呈现先增加后减小的趋势

在试验压力为30 N时摩擦因数最大

压力为40 N时磨损率最大; 摩擦表面连续氧化膜的生成有助于减轻Ti

SiC

材料的磨损.

Abstract

SiC

material was prepared with infiltration-sintering technology

and the performance influence factors of Ti

SiC

were analyzed. The results show that: at infiltration temperature of 1 500 ℃ and infiltration height of 6 mm

the best infiltration holding time is 30 min; Flexural strength of the sample increases with the increasing Ti

SiC

phase; friction factor and wear rate of the sample first increase and then decrease with the increasing pressure

and the friction factor and wear rate get the maximum when the pressure is 30 N and 40 N

respectively; and the continuous oxide film is of benefit to reducing wear and tear of Ti

SiC

material.

关键词

Keywords

references

BARSOUM M W.反应烧结Ti3SiC2材料干摩擦磨损性能的研究[D].西安: 西安理工大学材料科学与工程学院,2008.

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Dry Friction and Wear Properties of Ti3SiC2 Ceramic under Different Pressure

Tribological Properties of the Lubricant Released by Temperature-Sensitive Hydrogel

Effects of Ti3SiC2 Content on the Microstructure and Properties of Heat Treated(Ti5Si3+TiC)/TC4 Composites

Turbulent Kinetic Energy Dissipation Mechanism of Supercritical Carbon Dioxide Leakage Flow in a Scallop Bionic Seal Cavity

Effects of Steam Addition on the Swirl Combustion and Emission Characteristics of Cracked Ammonia

Related Author

张珊珊

谢辉

李月

郭俊德

董国忠

董光能

王芝萍 1

Related Institution

School of Mechanical Engineering, Xi'an Jiaotong University

State Key Laboratory for Mechanical Behavior of Materials, Xi’an Jiaotong University

Institute of Foundry Technology and Wear Resistant Materials, Xi’an Jiaotong University

⁰

Performance Influence Factors on Ti3SiC2 Synthesized by Infiltration-Sintering Technology

DOI：

摘要

Abstract

关键词

Keywords

references

Performance Influence Factors on Ti₃SiC₂ Synthesized by Infiltration-Sintering Technology